diff --git a/README.md b/README.md
index f20d120..719b00c 100644
--- a/README.md
+++ b/README.md
@@ -1,32 +1,85 @@
 
 # Fuzzy Guacamole Controller
 
-Fuzzy Guacamole Controller is a custom Raspberry Pi OS designed to make printing as user friendly and trouble free as possible.
+Fuzzy Guacamole Controller is a custom Raspberry Pi OS designed to make 3D printing as user friendly and trouble free as possible. It provides a web interface for uploading and executing print jobs on any 3d printer that runs Marlin firmware.
 
+## Supported technologies
+Fuzzy Guacamole Controller has only been tested on the Raspberry Pi 4 but it should work on all the currently released pis. It has been tested on 3d printers running Marlin 1 and Marlin 2 firmware.
 
 ## Installation
 
-Install Fuzzy Guacamole by installing the latest image to an sd card.
+Install Fuzzy Guacamole Controller using either the install script or custom image.
 
-#### Step 1
+### Install from install script
+**Step 1**\
+Open your pi's terminal.
+
+**Step 2**\
+Download the latest `install.sh` file using the following command:
+```bash
+wget https://raw.githubusercontent.com/3DCrowd/fuzzy-guacamole/main/install.sh
+```
+
+**Step 3**\
+Mark the install script as executable.
+```bash
+sudo chmod +x install.sh
+```
+
+**Step 4**\
+Run the install script
+```bash
+sudo ./install.sh
+```
+
+**Step 5**\
+Restart your pi
+```bash
+sudo reboot
+```
+
+**Step 6**\
+Finally, connect the pi to the printer with a suitable usb cable and select the port on the Fuzzy Guacamole Dashboard to see the connected printers controls.
+
+
+### Install from custom image.
+**Step 1**\
 Download the latest version of [Balena Etcher](https://www.balena.io/etcher/).
 
-#### Step 2
+**Step 2**\
 Download the latest Fuzzy Guacamole `.img` file from the [releases tab](https://github.com/3DCrowd/fuzzy-guacamole/releases/).
 
-#### Step 3
-Use Balena Etcher to burn the lastest image to the sd card.
+**Step 3**\
+Use Balena Etcher to burn the latest image to the sd card.
 
-#### Step 4
+**Step 4**\
 If you are planning on connecting to the printer over wifi create a `wpa_supplicant.conf` as outlined [here](https://www.raspberrypi.org/documentation/computers/configuration.html#configuring-networking-2) and place it in the boot partion of the sd card.
+
 (Note: This step is not required if using a wired ethernet connection).
 
-#### Step 5
-Plug the sd card into the pi and connect it to power. After a few minutes you should be able to access it by navigating to [fuzzyguacamole.local](http://fuzzyguacamole.local) when connected to the same wifi network.
+**Step 5**\
+Plug the sd card into the pi and connect it to power. After a few minutes you should be able to access it by navigating to [http://fuzzyguacamole.local](http://fuzzyguacamole.local) when connected to the same wifi network.
+
+**Step 6**\
+Finally, connect the pi to the printer with a suitable usb cable and select the port on the Fuzzy Guacamole Dashboard to see the connected printers controls.
+
+## Usage
+
+**Step 1**\
+Connect your 3D printer to your pi using a suitable usb cable.
+
+**Step 2**\
+Navigate to [http://fuzzyguacamole.local](http://fuzzyguacamole.local) while connected to the same wifi network that your pi is connected to.
+
+**Step 2**\
+Select the port of your printer from the dropdown and select *Try Again With This Port* to access the dashboard. 
 
-#### Step 6
-Finally, connect the pi to the printer with a suitable usb cable and reload the Fuzzy Guacamole Dashboard to see the connected printers controls.
+**Step 3**\
+Drag and drop your `.gcode` files into the upload gcode panel and hit print to send the file to the printer.
+## Screenshots
 
+![Could Not Connect Message](https://github.com/3DCrowd/fuzzy-guacamole/raw/main/readme_img/could_not_connect.png)
+![Fuzzy Guacamole Dashboard](https://github.com/3DCrowd/fuzzy-guacamole/raw/main/readme_img/dashboard.png)
 ## Roadmap
 
 - Support for local slicing
@@ -35,9 +88,7 @@ Finally, connect the pi to the printer with a suitable usb cable and reload the
 
 - User friendly connection to wifi
 
-  
 ## License
 
 [GNU General Public License v3.0](https://choosealicense.com/licenses/gpl-3.0/)
 
-