From a2b00da61ee0d4865e051d026934c3852162aaa1 Mon Sep 17 00:00:00 2001 From: shen <664376944@qq.com> Date: Sat, 9 Nov 2024 22:59:02 +0800 Subject: [PATCH] hwdef: Modify the contents of the README section and the hwdef parameters --- .../AP_HAL_ChibiOS/hwdef/AEROFOX-H7/README.md | 65 +++++++++---------- .../hwdef/AEROFOX-H7/defaults.parm | 6 -- .../AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat | 30 ++++----- 3 files changed, 41 insertions(+), 60 deletions(-) delete mode 100644 libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/README.md b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/README.md index b4a01160346756..a06abe5dc44c1c 100644 --- a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/README.md +++ b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/README.md @@ -30,50 +30,44 @@ The AEROFOX-H7 is a flight controller produced by AEROFOX(http://aerofox.cn) 4x ADC input FPC connector - The conneimgctor includes an SPI, an I2C, an PWM IMU heating control pin. Firmware - already includes drivers for ADIS16470, ICM45686, IMU heating, RM3100. It is - automatically identify after installation。 + The connector includes an SPI, an I2C, an PWM IMU heating control pin. ## Pinout ## UART Mapping -- SERIAL0 -> USB -- SERIAL1 -> UART7 -- SERIAL2 -> UART4 -- SERIAL3 -> UART5 -- SERIAL4 -> USART2 -- SERIAL5 -> USART1 GPS -- SERIAL6 -> UART8 TELEM -- SERIAL7 -> USART3 RCIN +All UARTs, except UART1, are DMA enabled. UART corresponding to each SERIAL port, and its default protocol, are shown below: +- SERIAL0 -> USB (MAVLink2) +- SERIAL1 -> UART7 (ESC Telemetry) +- SERIAL2 -> UART4 (User configured) +- SERIAL3 -> UART5 (User configured) +- SERIAL4 -> USART2 (User configured) +- SERIAL5 -> USART1 (GPS) +- SERIAL6 -> UART8 (MAVLink2) +- SERIAL7 -> USART3 (RCIN) ## RC Input -No special interface for RCIN is designed because any SERIAL interface can be used as -an RC input. +SERIAL 7 is configured for RC input by default and is compatible with all ArduPilot supported protocols except PPM. For protocols requiring half-duplex serial to transmit telemetry (such as FPort) you should set SERAIL7_OPTIONS = 4 (Half-Duplex) ## PWM Output -The AEROFOXH7 support up to 16PWM outputs. All pins support Dshot. Outputs 1-8 -supports STM32 native encoder mode and can input 4 groups of AB encoder signals simultaneously. - -- PWM1 TIM2_CH1 encoder mode -- PWM2 TIM2_CH2 encoder mode -- PWM3 TIM1_CH1 encoder mode -- PWM4 TIM1_CH2 encoder mode -- PWM5 TIM4_CH1 encoder mode -- PWM6 TIM4_CH2 encoder mode -- PWM7 TIM3_CH1 encoder mode -- PWM8 TIM3_CH2 encoder mode -- PWM9 TIM15_CH1 -- PWM10 TIM15_CH2 -- PWM11 TIM14_CH1 -- PWM12 TIM13_CH1 -- PWM13 TIM8_CH4 -- PWM14 TIM8_CH3 -- PWM15 TIM12_CH2 -- PWM16 TIM12_CH1 +The AEROFOXH7 support up to 16PWM outputs. All pins support DShot. Outputs 1-8 support bi-directional DShot. + +The 16 PWM outputs are in 9 groups: + +- PWM 1,2 in group1 +- PWM 3,4 in group2 +- PWM 5,6 in group3 +- PWM 7,8 in group4 +- PWM 9,10 in group5 +- PWM 11 in group6 +- PWM 12 in group7 +- PWM 13,14 in group8 +- PWM 15,16 in group9 + +Channels within the same group need to use the same output rate. If any channel in a group uses DShot, then all channels in that group need to use DShot. ## Battery Monitoring @@ -81,6 +75,7 @@ The board has a builting voltage and current sensor. The voltage sensor can hand to 12S LiPo batteries. ### The power A is onboard voltage sensor +It is enabled by default and has the following parameters set by default: - BATT_MONITOR 4 - BATT_VOLT_PIN 19 - BATT_CURR_PIN 9 @@ -92,13 +87,11 @@ to 12S LiPo batteries. - BATT_VOLT_PIN 10 - BATT_CURR_PIN 11 - BATT_VOLT_MULT 34 -- BATT_AMP_PERVLT 60 +- BATT_AMP_PERVLT should be set as required by the specific monitor used ## Compass -A 5883L compass is installed inside the H7 flight control. When high current devices such -as ESC and BEC are installed under the flight control board, the on-board compass -needs to be disabled. +A 5883L compass is installed inside the H7 flight control. When high current devices such as ESC and BEC are installed under the flight control board, the on-board compass is usually disabled and an external compass used mounted to minimize motor current effects. ## Loading Firmware The board comes pre-installed with an ArduPilot compatible bootloader, allowing the diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm deleted file mode 100644 index 330f9e35c6187c..00000000000000 --- a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm +++ /dev/null @@ -1,6 +0,0 @@ -ARSPD_TYPE 8 -BATT_VOLT_PIN 19 -BATT_VOLT_MULT 21 -BATT_MONITOR 3 -CAN_P1_DRIVER 1 -Q_ENABLE 1 diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat index 37a32582a10f52..d315c521b5332a 100644 --- a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat +++ b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat @@ -12,13 +12,8 @@ FLASH_SIZE_KB 2048 # bootloader is installed at zero offset FLASH_RESERVE_START_KB 128 -# UART1 is debug -PA9 USART1_TX USART1 NODMA -PA10 USART1_RX USART1 NODMA -define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_ESCTelemetry - PA11 OTG_FS_DM OTG1 -PA12 OTG_FS_DP OTG1# crystal frequency +PA12 OTG_FS_DP OTG1 # supports upto 8MBits/s CANFD_SUPPORTED 8 @@ -41,32 +36,28 @@ define DEFAULT_SERIAL1_BAUD 115200 # serial2 PC10 UART4_TX UART4 PC11 UART4_RX UART4 -define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_None -define DEFAULT_SERIAL2_BAUD 115200 # serial3 PC12 UART5_TX UART5 PD2 UART5_RX UART5 -define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_None -define DEFAULT_SERIAL3_BAUD 115200 # serial4 PD5 USART2_TX USART2 PD6 USART2_RX USART2 -define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_None -define DEFAULT_SERIAL4_BAUD 115200 + +# serial5 +PA9 USART1_TX USART1 NODMA +PA10 USART1_RX USART1 NODMA +define DEFAULT_SERIAL5_PROTOCOL SerialProtocol_GPS # serial6 PE1 UART8_TX UART8 PE0 UART8_RX UART8 define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_MAVLink2 -define DEFAULT_SERIAL6_BAUD 115200 # serial7 PD8 USART3_TX USART3 PD9 USART3_RX USART3 -define DEFAULT_SERIAL7_PROTOCOL SerialProtocol_RCIN -define DEFAULT_SERIAL7_BAUD 115200 # default the 2nd interface to SLCAN define HAL_OTG2_PROTOCOL SerialProtocol_SLCAN @@ -208,8 +199,6 @@ define HAL_I2C_INTERNAL_MASK 1 PA13 JTMS-SWDIO SWD PA14 JTCK-SWCLK SWD -#include sdcard.inc - define HAL_CHIBIOS_ARCH_FMUV3 1 define BOARD_TYPE_DEFAULT 3 @@ -235,4 +224,9 @@ DMA_NOSHARE SPI2* UART2* UART4* UART5* ENABLE_DFU_BOOT 1 - +define HAL_BATT_MONITOR 4 +define HAL_BATT_VOLT_PIN 19 +define HAL_BATT_CURR_PIN 9 +define HAL_BATT_VOLT_SCALE 21 +define HAL_BATT_CURR_SCALE 90.9 +define HAL_CAN_P1_DRIVER 1 \ No newline at end of file