Initial profile switch work

app/CMakeLists.txt

@@ -87,6 +87,7 @@ target_sources_ifdef(CONFIG_USB_DEVICE_STACK app PRIVATE src/usb.c)
 target_sources_ifdef(CONFIG_ZMK_USB app PRIVATE src/usb_hid.c)
 target_sources_ifdef(CONFIG_ZMK_RGB_UNDERGLOW app PRIVATE src/rgb_underglow.c)
 target_sources_ifdef(CONFIG_ZMK_BACKLIGHT app PRIVATE src/backlight.c)
+target_sources_ifdef(CONFIG_ZMK_PROFILESWITCH app PRIVATE src/profile_switch.c)
 target_sources(app PRIVATE src/workqueue.c)
 target_sources(app PRIVATE src/main.c)
 

app/Kconfig

@@ -180,6 +180,10 @@ config BT_PERIPHERAL_PREF_LATENCY
 config BT_PERIPHERAL_PREF_TIMEOUT
     default 400
 
+config ZMK_PROFILESWITCH
+    bool "Enable two state profile switch"
+    default n
+
 #ZMK_BLE
 endif
 

app/dts/bindings/zmk,profile-switch.yaml

@@ -0,0 +1,14 @@
+# Copyright (c) 2020 The ZMK Contributors
+# SPDX-License-Identifier: MIT
+
+description: |
+  Generic driver for controlling the bluetooth profile on the
+  switch-gpio pin status
+  (Only in supported hardware)
+
+compatible: "zmk,profile-switch"
+
+properties:
+  switch-gpios:
+    type: phandle-array
+    required: true

app/src/profile_switch.c

@@ -0,0 +1,65 @@
+#include <zephyr/device.h>
+#include <zephyr/init.h>
+#include <zephyr/kernel.h>
+#include <zephyr/logging/log.h>
+#include <zephyr/drivers/gpio.h>
+
+#include <zmk/ble.h>
+#include <zmk/workqueue.h>
+
+LOG_MODULE_DECLARE(zmk, CONFIG_ZMK_LOG_LEVEL);
+
+BUILD_ASSERT(DT_HAS_CHOSEN(zmk_profileswitch),
+             "CONFIG_ZMK_PROFILESWITCH is enabled but no zmk,profileswitch chosen node found");
+
+struct gpio_callback a_gpio_cb;
+const struct gpio_dt_spec switchgpio = GPIO_DT_SPEC_GET(DT_CHOSEN(zmk_profileswitch), switch_gpios);
+
+static void zmk_profile_switch_read() {
+    uint8_t val = gpio_pin_get_dt(&switchgpio);
+    LOG_DBG("Setting BLE profile to %d", val);
+    zmk_ble_prof_select(val);
+    if (gpio_pin_interrupt_configure_dt(&switchgpio, GPIO_INT_EDGE_BOTH)) {
+        LOG_WRN("Unable to set A pin GPIO interrupt");
+    }
+}
+
+static void zmk_profile_switch_work_cb(struct k_work *work) { zmk_profile_switch_read(); }
+
+K_WORK_DEFINE(profileswitch_work, zmk_profile_switch_work_cb);
+
+static void zmk_profile_switch_callback(const struct device *dev, struct gpio_callback *cb,
+                                        uint32_t pins) {
+
+    if (gpio_pin_interrupt_configure_dt(&switchgpio, GPIO_INT_DISABLE)) {
+        LOG_WRN("Unable to set A pin GPIO interrupt");
+    }
+    LOG_DBG("interrupt triggered");
+    k_work_submit_to_queue(zmk_workqueue_lowprio_work_q(), &profileswitch_work);
+}
+
+static int zmk_profile_switch_init(const struct device *_arg) {
+
+    if (!device_is_ready(switchgpio.port)) {
+        LOG_ERR("A GPIO device is not ready");
+        return -EINVAL;
+    }
+    if (gpio_pin_configure_dt(&switchgpio, GPIO_INPUT)) {
+        LOG_DBG("Failed to configure A pin");
+        return -EIO;
+    }
+    gpio_init_callback(&a_gpio_cb, zmk_profile_switch_callback, BIT(switchgpio.pin));
+
+    if (gpio_add_callback(switchgpio.port, &a_gpio_cb) < 0) {
+        LOG_DBG("Failed to set A callback!");
+        return -EIO;
+    }
+    if (gpio_pin_interrupt_configure_dt(&switchgpio, GPIO_INT_EDGE_BOTH)) {
+        LOG_WRN("Unable to set A pin GPIO interrupt");
+    }
+    LOG_DBG("Setting profile now");
+    zmk_profile_switch_read();
+    return 0;
+}
+
+SYS_INIT(zmk_profile_switch_init, APPLICATION, CONFIG_APPLICATION_INIT_PRIORITY);