-
Notifications
You must be signed in to change notification settings - Fork 13
/
ASIC-README
169 lines (119 loc) · 5.92 KB
/
ASIC-README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
SUPPORTED DEVICES
Currently supported devices include the Avalon, the Butterfly Labs SC range
of devices and the ASICMINER block erupters.
The BFL devices should come up as one of the following:
BAJ: BFL ASIC Jalapeño
BAL: BFL ASIC Little Single
BAS: BFL ASIC Single
BAM: BFL ASIC Minirig
BFL devices need the --enable-bflsc option when compiling cgminer yourself.
Avalon will come up as AVA.
Avalon devices need the --enable-avalon option when compiling cgminer.
ASICMINER block erupters will come up as AMU.
ASICMINER devices need the --enable-icarus option when compiling cgminer.
GETTING STARTED WITH BUTTERFLY LABS ASICS
Unlike other software, cgminer uses direct USB communication instead of the
ancient serial USB communication to be much faster, more reliable and use a
lot less CPU. For this reason, setting up for mining with cgminer on these
devices requires different drivers.
WINDOWS:
On windows, the direct USB support requires the installation of a WinUSB
driver (NOT the ftdi_sio driver), and attach it to the Butterfly labs device.
The easiest way to do this is to use the zadig utility which will install the
drivers for you and then once you plug in your device you can choose the
"list all devices" from the "option" menu and you should be able to see the
device as something like: "BitFORCE SHA256 SC". Choose the install or replace
driver option and select WinUSB. You can either google for zadig or download
it from the cgminer directory in the DOWNLOADS link above.
When you first switch a device over to WinUSB with zadig and it shows that
correctly on the left of the zadig window, but it still gives permission
errors, you may need to unplug the USB miner and then plug it back in
LINUX:
On linux, the direct USB support requires no drivers at all. However due to
permissions issues, you may not be able to mine directly on the devices as a
regular user without giving the user access to the device or by mining as
root (administrator). In order to give your regular user access, you can make
him a member of the plugdev group with the following commands:
sudo usermod -G plugdev -a `whoami`
If your distribution does not have the plugdev group you can create it with:
sudo groupadd plugdev
In order for the BFL devices to instantly be owned by the plugdev group and
accessible by anyone from the plugdev group you can copy the file
"01-cgminer.rules" from the cgminer archive into the /etc/udev/rules.d
directory with the following command:
sudo cp 01-cgminer.rules /etc/udev/rules.d/
After this you can either manually restart udev and re-login, or more easily
just reboot.
AVALON DEVICES
Currently all known Avalon devices come with their own operating system and
a preinstalled version of cgminer as part of the flash firmware, based on the
most current cgminer version so no configuration should be necessary. It is
possible to plug a USB cable from a PC into the Avalon device and mine using
cgminer as per any other device. It will autodetect and hotplug using default
options. You can customise the avalon behaviour by using the avalon-options
command, and adjust its fan control-temperature relationship with avalon-temp.
By default the avalon will also cut off when its temperature reaches 60
degrees.
Avalon commands:
--avalon-auto Adjust avalon overclock frequency dynamically for best hashrate
--avalon-cutoff <arg> Set avalon overheat cut off temperature (default: 60)
--avalon-options <arg> Set avalon options baud:miners:asic:timeout:freq
--avalon-temp <arg> Set avalon target temperature (default: 50)
Avalon auto will enable dynamic overclocking gradually increasing and
decreasing the frequency till the highest hashrate that keeps hardware errors
around 1% is achieved. This WILL run your avalon beyond its normal specification
so the usual warnings apply. When avalon-auto is enabled, the avalon-options
for frequency and timeout are used as the starting point only.
eg:
--avalon-temp 55
This will adjust fanspeed to keep the temperature at or slightly below 55.
If you wish the fans to run at maximum speed, setting the target temperature
very low such as 0 will achieve this. This option can be added to the "More
options" entry in the web interface if you do not have a direct way of setting
it.
eg:
--avalon-cutoff 65
This will cut off the avalon should it get up to 65 degrees and will then
re-enable it when it gets to the target temperature as specified by avalon-temp.
eg:
--avalon-options 115200:24:10:45:282
The values are baud : miners : asic count : timeout : frequency.
Baud:
The device is pretty much hard coded to emulate 115200 baud so you shouldn't
change this.
Miners:
Most Avalons are 3 module devices, which come to 24 miners. 4 module devices
would use 32 here.
Asic count:
Virtually all have 10, so don't change this.
Timeout:
This is how long the device will work on a work item before accepting new work
to replace it. It should be changed according to the frequency (last setting).
It is possible to set this a little lower if you are trying to tune for short
block mining (eg p2pool) but much lower and the device will start creating
duplicate shares.
Sample settings for valid different frequencies (last 2 values):
34:375 *
36:350 *
39:325 *
43:300
45:282 (default)
47:270
50:256
Frequency:
This is the clock speed of the devices. Only specific values work, 256, 270,
282 (default), 300, 325, 350 and 375.
Note that setting a value with an asterisk next to it will be using your
avalon outside its spec and you do so at your own risk.
If you use the full curses based interface with Avalons you will get this
information:
AVA 0: 22/ 46C 2400R
The values are:
ambient temp / highest device temp lowest detected ASIC cooling fan RPM.
Use the API for more detailed information than this.
---
This code is provided entirely free of charge by the programmer in his spare
time so donations would be greatly appreciated. Please consider donating to the
address below.
Con Kolivas <[email protected]>
15qSxP1SQcUX3o4nhkfdbgyoWEFMomJ4rZ