It is very easy for the user to use Vitis/Vivado RTL Kernel Wizard to create and develop RTL based kernel which could be seamlessly integrated with other HLS C or Vitis Vision library based kernel with Vitis. This tutorial will show the detailed steps to create rtc_gen kernel. We use Alveo U200 as the target platform for the tutorial.
The rtc_gen kernel is required to read font library from global memory into on-chip SRAM, then output the clock image via AXI stream port. Considerting the font library reading is a one-time job, and no global memory bandwidth requirement exists during normal work, so we use 32-bit (data bus) AXI4 master interface for the font reading port to save resources. In the downstream processing pipeline, we will use XF_NPP8 format (processing 8 pixels in each clock cycle), so we select the AXI stream width as 64-bit, which could transfer eight pixels in each AXI stream transaction. For control register, we will use an AXI slave interface compatible with XRT, so we could use the standard OpenCL API to program and control the kernel.
Thus we generalize the top level design specification for rtc_gen kernel as below:
Bus interfaces
- AXI-Lite slave interface for control
- AXI-Lite master interface for font data loading, data width 32-bit, address width 64-bit
- AXI stream master interface for clock digit image output, data width 64-bit
Control Register
No. | Arguments | Width | Description |
---|---|---|---|
0 | work_mode | 1 | [0]: determine the kernel working mode 0 - load font from global memory to on-chip SRAM via AXI read master 1 - output RTC digit figure via AXI steam master |
1 | cs_count | 32 | [21:0]: Centi-second counter. For example, if the system clock is 200MHz, cs_count should be set to 2,000,000 |
2 | time_format | 1 | [0]: determine whether centisecond is included in the output digit images 0 - disable centiseconds output 1 - enable centiseconds output |
3 | time_set_val | 32 | Set time value for internal free-running clock: [31:24] - hours [23:16] - minutes [15:8] - seconds [7:0] - centi-seconds |
4 | time_set_en | 1 | [0]: write 1 to this bit will load the time_set_value to internal free-running clock. |
5 | time_val | 32 | Read-only regsiter for internal real-time-clock time value: [31:24] - hours [23:16] - minutes [15:8] - seconds [7:0] - centi-seconds |
6 | read_addr | 64 | AXI master pointer, this is the FPGA device buffer address for font library |
Now we use RTL Kernel Wizard to create the frame for rtc_gen kernel. We will launch the Wizard from Vivado. Please refer to Vitis Application Acceleration Development Flow Documentation for detailed user guide of RTL kernel and RTL Kernel Wizard.
Please change to ./rtc_gen directory of the git repo, create a directory named vivado_project, then enter this directory.
cd ./rtc_gen
mkdir vivado_project
cd ./vivado_project
vivado &
We create a new RTL project named rtc_gen_kernel in the just created vivado_project directory. During the part selection page, select *Alveo U200 Data Center Accelerator Card.
When the project is created, in the Flow Navigator, click the IP catalog command, type RTL Kernel in the IP catalog search box, then double-click RTL Kernel Wizard to launch the wizard.
In the General Settings tab of the RTL Kernel Wizard, set the kernel name to rtc_gen, set the kernel vendor to xilinx.com, change the has reset option to value 1, refer to below snapshot.
In the Scalars tab, configure the kernel arguments as our design specification. Refer to the Control Register table and below snapshot. Please note read_addr register is not considered scalar argument as AXI master pointer, so we don't need to configure it in this tab. We are using uint as argument type here, though all these bit might not be used.
In the Global Memory tab, configure the AXI master interfaces parameters according to our design specification. Name the AXI master interface to fontread_axi_m, change the width to 4 bytes (32-bit), and set the relating argument name to read_addr. Refer to below snapshot.
In the Streaming interfaces tab, set the number of AXI4-Sttream interfaces to 1, name it to dataout_axis_m, set the mode the Master, and set the width to 8 bytes (64-bit). Refer to below snapshot.
Finally review the summary page of the wizard, and click OK button to generate the RTL kernel top level framework.
For the next "Generate Output Products" pop-up window, just click Skip button close the window. Now you can see the rtc_gen.xci file in the Design Sources group of Sources view. Right click the rtc_gen.xci file, select Open IP Example Design.
In the Open IP Example Design pop-up window directly click OK button, then another project named rtc_gen_ex will be created in ./vivado_project directory and open automatically in another Vivado session. We will use project rtc_gen_ex as the major working project to finish the rtc_gen kernel development.
In the rtc_gen_ex project, you can see a few automatically generated Verilog/SystemVerilog source code files:
rtc_gen_control_s_axi.v
rtc_gen_example_adder.v
rtc_gen_example_axi_read_master.sv
rtc_gen_example_axi_write_master.sv
rtc_gen_example_counter.sv
rtc_gen_example_number_generator.sv
rtc_gen_example.sv
rtc_gen_example_vadd_axis.sv
rtc_gen_example_vadd.sv
rtc_gen_tb.sv
rtc_gen.v
In the Sources view, Hierarchy tab, we can see the HDL file hierarchy. Now we have finished the kernel framework creation.
We will use following generated RTL files in our rtc_gen kernel:
-
rtc_gen_control_s_axi.v
It is the AXI Lite slave interface to upper level system and XRT. It includes all the kernel argument as well as the kernel control signals (ap_start, ap_done, ap_idle, ap_ready). We will modify this module a little to realize the read-only register time_val.
-
rtc_gen_example_axi_read_master.sv
It is a simple AXI Lite read master which could be called by our kernel directly. It uses four control signals to trigger the master to finish data reading tasks:
- ctrl_start: single cycle pulse to start the master state machine
- ctrl_done: single cycle pulse indicating the finish the AXI reading task
- ctrl_addr_offset: base address for AXI reading operation. Kernel argument read_addr can be used to drive this signal
- ctrl_xfer_size_in_bytes: number of byes to be read from AXI bus.
The example master also use an AXI stream port for reading data transfer, which could be connected to FIFO like data pipeline easily.
-
rtc_gen_example_counter.sv
The sub-module of the example AXI read master.
-
rtc_gen.v It is the example top level kernel wrapper instantiating all the submodule. We will modify this module to construct our rtc_gen kernel.
-
rt_gen_tb.sv It is an example testbench using Xilinx AXI Verification IP. We can modify this testbench to test our rtc_gen kernel.
In addition to these five files, we could also refer to rtc_gen_example_vadd.sv for the connection of AXI read master. For AXI stream port, it is simple and we don't need the example for reference. For rtc_gen kernel, a Verilog file rtc_gen_core.v is created to finish the core function of the kernel. The function diagram of rtc_gen_core is shown in following diagram.
To make the core source code directory clean, we put all the necessary generated, newly composed or modified RTL files in ~/rtc_gen/src directory. Please review the directory for these source code files. Please note SPSR.v is a parameterized SRAM template which could be synthesized to FPGA BlockRAM.
./rtc_gen/src/rtc_gen_control_s_axi.v
./rtc_gen/src/rtc_gen_core.v
./rtc_gen/src/rtc_gen_example_axi_read_master.sv
./rtc_gen/src/rtc_gen_example_counter.sv
./rtc_gen/src/rtc_gen_tb.sv
./rtc_gen/src/rtc_gen.v
./rtc_gen/src/SPSR.v
Now we remove all the existing Verilog/SystemVerilog source codes (except for thos in IP group) from the rtc_gen_ex project in Vivado, then add the files in ./rtc_gen/src to the project (rtc_gen_tb.sv for Simulation-Only Sources, other files for Design Sources). Thus you can see the design hierarchy as below snapshot, and we finish the coding for kernel rtc_gen.
Now you can simulation the design and go through normal RTL design flow with standard Vivado design methodology. A text format font library file font_sim_data.txt in ./rtc_gen directory is provided, which could be read in by testbench rtc_gen_tb.sv for simulation. Please copy it to ./rtc_gen/vivado_project/rtc_gen_ex/rtc_gen_ex.sim/sim_1/behav/xsim/ for simulation runs.
After you confirm the design is OK, select Generate RTL Kernel from Flow Menu, then select Sources-only kernel in the pop-up window, click OK button to finish the rtc_gen RTL kernel creation.
The generated kernel file is ./rtc_gen/vivado_project/rtc_gen_ex/rtc_gen.xo, which can be used in downstream Vitis intergartion flow. From the Vivado Tcl Console view, you can see the Vivado actually use following command line to finish the kernel packaging:
package_xo -xo_path ./rtc_gen/vivado_project/rtc_gen_ex/exports/rtc_gen.xo \
-kernel_name rtc_gen \
-ip_directory ./rtc_gen/vivado_project/rtc_gen_ex/rtc_gen \
-kernel_xml ./rtc_gen/vivado_project/rtc_gen_ex/imports/kernel.xml
./rtc_gen/vivado_project/rtc_gen_ex/rtc_gen is the folder for rtc_gen IP, and ./rtc_gen/vivado_project/rtc_gen_ex/imports/kernel.xml is the kernel description file. So we could copy out these items to standlone directory and just use the command line above to package the kernel. This is also where the ./hw/rtc_gen_ip directory and ./hw/rtc_gen_kernel.xml file come from.
Return to Top-Level of Tutorial
Copyright © 2020–2023 Advanced Micro Devices, Inc