-
Notifications
You must be signed in to change notification settings - Fork 11
/
README
48 lines (47 loc) · 3.31 KB
/
README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Version 2.10
Usage: emmcdl <option> <value>
Options:
-l List available mass storage devices
-info List HW information about device attached to COM (eg -p COM8 -info)
-MaxPayloadSizeToTargetInBytes The max bytes in firehose mode (DDR or large IMEM use 16384, default=8192)
-SkipWrite Do not write actual data to disk (use this for UFS provisioning)
-SkipStorageInit Do not initialize storage device (use this for UFS provisioning)
-MemoryName <ufs/emmc> Memory type default to emmc if none is specified
-SetActivePartition <num> Set the specified partition active for booting
-disk_sector_size <int> Dump from start sector to end sector to file
-d <start> <end> Dump from start sector to end sector to file
-d <PartName> Dump entire partition based on partition name
-d logbuf@<start> <size> Dump size of logbuf to the console
-e <start> <num> Erase disk from start sector for number of sectors
-e <PartName> Erase the entire partition specified
-s <sectors> Number of sectors in disk image
-p <port or disk> Port or disk to program to (eg COM8, for PhysicalDrive1 use 1)
-o <filename> Output filename
[<-x <*.xml> [-xd <imgdir>]>...] Program XML file to output type -o (output) -p (port or disk)
-f <flash programmer> Flash programmer to load to IMEM eg MPRG8960.hex
-i <singleimage> Single image to load at offset 0 eg 8960_msimage.mbn
-t Run performance tests
-b <prtname> <binfile> Write <binfile> to GPT <prtname>
-g GPP1 GPP2 GPP3 GPP4 Create GPP partitions with sizes in MB
-gq Do not prompt when creating GPP (quiet)
-r Reset device
-ffu <*.ffu> Download FFU image to device in emergency download need -o and -p
-splitffu <*.ffu> -o <xmlfile> Split FFU into binary chunks and create rawprogram0.xml to output location
-protocol <s|f> Can be <s>(STREAMING), default is <f>(FIREHOSE)
-gpt Dump the GPT from the connected device
-raw Send and receive RAW data to serial port 0x75 0x25 0x10
-wimei <imei> Write IMEI <imei>
-v Enable verbose output
Examples:
emmcdl -p ttyUSB0 -info
emmcdl -p ttyUSB0 -gpt
emmcdl -p ttyUSB0 -SkipWrite -SkipStorageInit -MemoryName ufs -f prog_emmc_firehose_8994_lite.mbn -x memory_configure.xml
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -x rawprogram0.xml -SetActivePartition 0
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -x rawprogram0.xml -xd imagedir -SetActivePartition 0
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -ffu wp8.ffu
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -d 0 1000 -o dump_1_1000.bin
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -d SVRawDump -o svrawdump.bin
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -b SBL1 c:\temp\sbl1.mbn
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -e 0 100
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -e MODEM_FSG
emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -raw 0x75 0x25 0x10