menu_calibration.cfg

# Adds a calibration menu item, inspiration from /u/VonThing

[menu __calibration]
type: list
name: Calibration
items:
    __calibration_test_bltouch
    __calibration_reset_bltouch
    __calibration_home_all_axes
    __calibration_bed_screws_adjust
    __calibration_bed_mesh_calibrate
    __calibration_screws_calculate
    __calibration_probe_calibrate
    __calibration_probe_accuracy
    __general_firmware_restart

[menu __calibration_accept]
type: command
name: Accept
gcode: ACCEPT

[menu __calibration_abort]
type: command
name: Abort
gcode: ABORT
action: back

[menu __calibration_test_bltouch]
type: command 
name: Test BLTouch
gcode: BLTOUCH_DEBUG COMMAND=self_test

[menu __calibration_reset_bltouch]
type: command 
name: Test BLTouch
gcode: BLTOUCH_DEBUG COMMAND=reset

[menu __calibration_screws_calculate]
type: command
name: Screw tilt calculate
gcode:
    G28
    SCREWS_TILT_CALCULATE

[menu __calibration_bed_screws_adjust]
type: list
name: Adjust screws
enter_gcode: 
    G28
    BED_SCREWS_ADJUST
show_back: False
items:
    __calibration_accept
    __calibration_bed_screws_adjust_adjusted
    __calibration_save_config
    __calibration_abort

[menu __calibration_probe_accuracy]
type: command
name: Test accuracy
gcode:
    G28
    G0 X164 Y134 Z10 F6000
    PROBE_ACCURACY 

[menu __calibration_save_config]
type: command
name: Save config
gcode: SAVE_CONFIG

[menu __general_firmware_restart]
type: command
name: Restart firmware
gcode: FIRMWARE_RESTART

[menu __calibration_home_all_axes]
type: command
name: Home XYZ
gcode: G28

[menu __calibration_bed_screws_adjust_adjusted]
type: command
name: Adjusted
gcode: ADJUSTED

[menu __calibration_probe_calibrate]
type: list
show_back: False
name: Adjust Z offset
enter_gcode:
    G28
    G0 Z10 F6000
    PROBE_CALIBRATE
items:
    __calibration__toolhead_zpos
    __calibration_probe_calibrate_testz_minus, __calibration_probe_calibrate_testz_plus 
    __calibration_probe_calibrate_testz_minus_minus, __calibration_probe_calibrate_testz_plus_plus
    __calibration_probe_calibrate_testz_minus_1, __calibration_probe_calibrate_testz_plus_1
    __calibration_probe_calibrate_testz_minus_point_1, __calibration_probe_calibrate_testz_plus_point_1
    __calibration_accept
    __calibration_save_config
    __calibration_abort

[menu __calibration__toolhead_zpos]
type: item
width: 16
name: "Z = {0:.3f}"
cursor: \x20
parameter: toolhead.zpos

[menu __calibration_probe_calibrate_testz_minus]
cursor: \x20
type: command
width: 7
name: "   -"
gcode: TESTZ Z=-

[menu __calibration_probe_calibrate_testz_plus]
cursor: \x20
type: command
name: "   +"
width: 7
gcode: TESTZ Z=+

[menu __calibration_probe_calibrate_testz_minus_minus]
cursor: \x20
type: command
name: "   --"
width: 7
gcode: TESTZ Z=--

[menu __calibration_probe_calibrate_testz_plus_plus]
cursor: \x20
type: command
name: "   ++"
width: 7
gcode: TESTZ Z=++

[menu __calibration_probe_calibrate_testz_minus_1]
cursor: \x20
type: command
name: "  -1.0"
width: 7
gcode: TESTZ Z=-1

[menu __calibration_probe_calibrate_testz_plus_1]
cursor: \x20
type: command
name: "  +1.0"
width: 7
gcode: TESTZ Z=+1

[menu __calibration_probe_calibrate_testz_minus_point_1]
cursor: \x20
type: command
name: "  -0.1"
width: 7
gcode: TESTZ Z=-0.1

[menu __calibration_probe_calibrate_testz_plus_point_1]
cursor: \x20
type: command
name: "  +0.1"
width: 7
gcode: TESTZ Z=+0.1

[menu __calibration_bed_mesh_calibrate]
type: command
name: Generate bed mesh
width: 18
gcode: 
    G29
    SAVE_CONFIG
    FIRMWARE_RESTART

# items:
#     __calibration_card_bed_mesh

# [menu __calibration_card_bed_mesh]
# type: card
# name: Calibration card
# content:
#     "{0}"
#     ""
#     "   Will reboot"
#     "  when complete"
# items:
#     __calibration_bed_mesh_calibrate_text_1
    
# [menu __calibration_bed_mesh_calibrate_text_1]
# type: item
# name: "  [In progress]"
# cursor: \x20