install.md

Installation and Usage

• Prerequisites
  • Software required
  • Hardware required
  • Persistent memory pre-provisioning
• Installation and setup
  • Install PMEM-CSI driver
    • Install using the operator
    • Install from source
  • Automatic node setup
  • Volume parameters
  • Kata Containers support
  • Ephemeral inline volumes
  • Raw block volumes
  • Enable scheduler extensions
  • Metrics support
• PMEM-CSI Deployment CRD
• Filing issues and contributing

Overview

This section summarizes the steps that may be needed during the entire lifecycle of PMEM in a cluster, starting with the initial preparations and ending with decommissioning the hardware. The other sections explain each step in more detail.

When setting up a cluster, the administrator must install the PMEM hardware on nodes and configure some or all of those instances of PMEM for usage by PMEM-CSI (prerequisites]. Nodes where PMEM-CSI is supposed to run must have a certain label in Kubernetes.

The administrator must install PMEM-CSI, using the PMEM-CSI operator (recommended) or with scripts and YAML files in the source code. The default install settings should work for most clusters. Some clusters don't use /var/lib/kubelet as the data directory for kubelet and then the corresponding PMEM-CSI setting must be changed accordingly because otherwise kubelet does not find PMEM-CSI. The operator has an option for that in its API (kubeletDir in the DeploymentSpec), the YAML files can be edited or modified with kustomize.

A PMEM-CSI installation can only use direct device mode or LVM device mode. It is possible to install PMEM-CSI twice on the same cluster with different modes, with these restrictions:

• The driver names must be different.
• The installations must run on different nodes by using different node labels, or the "usage" parameter of the LVM mode driver installation one a node must be so that it leaves spaces available for the direct mode driver installation on that same node.

The administrator must decide which storage classes shall be available to users of the cluster. A storage class references a driver installation by name, which indirectly determines the device mode. A storage class also chooses which filesystem is used (xfs or ext4) and enables Kata Containers support.

Optionally, the administrator can enable the scheduler extensions (recommended) and monitoring of resource usage via the metrics support.

It is recommended to enable the scheduler extensions in combination with volumeBindingMode: WaitForFirstConsumer as in the pmem-storageclass-late-binding.yaml example. This ensures that pods get scheduled onto nodes that have sufficient RAM, CPU and PMEM. Without the scheduler extensions, it is random whether the scheduler picks a node that has PMEM available and immediate binding (the default volume binding mode) might work better. However, then pods might not be able to run when the node where volumes were created are overloaded.

Optionally, the log output format can be changed from the default "text" format (= the traditional glog format) to "json" (= output via zap) for easier processing.

When using the operator, existing PMEM-CSI installations can be upgraded seamlessly by installing a newer version of the operator. Downgrading by installing an older version is also supported, but may need manual work which will be documented in the release notes.

When using YAML files, the only reliable way of up- or downgrading is to remove the installation and install anew.

Users can then create PMEM volumes via persistent volume claims that reference the storage classes or via ephemeral inline volumes.

A node should only be removed from a cluster after ensuring that there is no pod running on it which uses PMEM and that there is no persistent volume (PV) on it. This can be checked via kubectl get -o yaml pv and looking for a nodeAffinity entry that references the node or via metrics data for the node. When removing a node or even the entire PMEM-CSI driver installation too soon, attempts to remove pods or volumes via the Kubernetes API will fail. Administrators can recover from that by force-deleting PVs for which the underlying hardware has already been removed.

By default, PMEM-CSI wipes volumes after usage (eraseAfter), so shredding PMEM hardware after decomissioning it is optional.

Prerequisites

Software required

The recommended mimimum Linux kernel version for running the PMEM-CSI driver is 4.15. See Persistent Memory Programming for more details about supported kernel versions.

Hardware required

Persistent memory device(s) are required for operation. However, some development and testing can be done using QEMU-emulated persistent memory devices. See the "QEMU and Kubernetes" section for the commands that create such a virtual test cluster.

Persistent memory pre-provisioning

The PMEM-CSI driver needs pre-provisioned regions on the NVDIMM device(s). The PMEM-CSI driver itself intentionally leaves that to the administrator who then can decide how much and how PMEM is to be used for PMEM-CSI.

Beware that the PMEM-CSI driver will run without errors on a node where PMEM was not prepared for it. It will then report zero local storage for that node, something that currently is only visible in the log files.

When running the Kubernetes cluster and PMEM-CSI on bare metal, the ipmctl utility can be used to create regions. App Direct Mode has two configuration options - interleaved or non-interleaved. One region per each NVDIMM is created in non-interleaved configuration. In such a configuration, a PMEM-CSI volume cannot be larger than one NVDIMM.

Example of creating regions without interleaving, using all NVDIMMs:

$ ipmctl create -goal PersistentMemoryType=AppDirectNotInterleaved

Alternatively, multiple NVDIMMs can be combined to form an interleaved set. This causes the data to be striped over multiple NVDIMM devices for improved read/write performance and allowing one region (also, PMEM-CSI volume) to be larger than single NVDIMM.

Example of creating regions in interleaved mode, using all NVDIMMs:

$ ipmctl create -goal PersistentMemoryType=AppDirect

When running inside virtual machines, each virtual machine typically already gets access to one region and ipmctl is not needed inside the virtual machine. Instead, that region must be made available for use with PMEM-CSI because when the virtual machine comes up for the first time, the entire region is already allocated for use as a single block device:

$ ndctl list -RN
{
  "regions":[
    {
      "dev":"region0",
      "size":34357641216,
      "available_size":0,
      "max_available_extent":0,
      "type":"pmem",
      "persistence_domain":"unknown",
      "namespaces":[
        {
          "dev":"namespace0.0",
          "mode":"raw",
          "size":34357641216,
          "sector_size":512,
          "blockdev":"pmem0"
        }
      ]
    }
  ]
}
$ ls -l /dev/pmem*
brw-rw---- 1 root disk 259, 0 Jun  4 16:41 /dev/pmem0

Labels must be initialized in such a region, which must be performed once after the first boot:

$ ndctl disable-region region0
disabled 1 region
$ ndctl init-labels nmem0
initialized 1 nmem
$ ndctl enable-region region0
enabled 1 region
$ ndctl list -RN
[
  {
    "dev":"region0",
    "size":34357641216,
    "available_size":34357641216,
    "max_available_extent":34357641216,
    "type":"pmem",
    "iset_id":10248187106440278,
    "persistence_domain":"unknown"
  }
]
$ ls -l /dev/pmem*
ls: cannot access '/dev/pmem*': No such file or directory

On some virtual machines, for example VMware® vSphere, the persistent memory does not support setting labels and the ndctl init-labels nmem0 command above would fail. What can be done in that case is to convert the existing namespace from "raw" to "fsdax" mode and then run PMEM-CSI in LVM mode. Direct mode is not possible because it depends on creating additional namespaces which in turn depends on support for labels. The command for conversion is:

$ ndctl create-namespace --force --reconfig=namespace0.0 --mode=fsdax --name=pmem-csi
{
  "dev":"namespace0.0",
  "mode":"fsdax",
  "map":"dev",
  "size":67643637760,
  "uuid":"9fa6976c-ab57-491b-a00c-e52d092a4fa8",
  "sector_size":512,
  "align":2097152,
  "blockdev":"pmem0",
  "name":"pmem-csi"
}

Note the pmem-csi name for the namespace: this is how PMEM-CSI in LVM mode knows that it is allowed to use this namespace. When the VM provides only "legacy PMEM", ndctl silently drops that name. In that case, the volume group as to be created manually:

$ vgcreate --force bus0region0fsdax /dev/pmem0

See automatic node setup below for instructions on how to automate this conversion.

Installation and setup

This section assumes that a Kubernetes cluster is already available with at least one node that has persistent memory device(s). For development or testing, it is also possible to use a cluster that runs on QEMU virtual machines, see the "QEMU and Kubernetes".

• Make sure that the alpha feature gates CSINodeInfo and CSIDriverRegistry are enabled

The method to configure alpha feature gates may vary, depending on the Kubernetes deployment. It may not be necessary anymore when the feature has reached beta state, which depends on the Kubernetes version.

• Label the cluster nodes that provide persistent memory device(s)

PMEM-CSI manages PMEM on those nodes that have a certain label. For historic reasons, the default in the YAML files and the operator settings is to use a label storage with the value pmem.

Such a label can be set for each node manually with:

$ kubectl label node <your node> storage=pmem

Alternatively, the Node Feature Discovery (NFD) add-on can be used to label nodes automatically. In that case, the default PMEM-CSI node selector has to be changed to "feature.node.kubernetes.io/memory-nv.dax": "true". The operator has the nodeSelector field for that. For the YAML files a kustomize patch can be used.

Install PMEM-CSI driver

PMEM-CSI driver can be deployed to a Kubernetes cluster either using the PMEM-CSI operator or by using reference yaml files provided in source code.

Install using the operator

PMEM-CSI operator facilitates deploying and managing the PMEM-CSI driver on a Kubernetes cluster.

Installing the operator from Operator Hub

If your cluster supports managing the operators using the Operator Lifecycle Manager, then it is recommended to install the PMEM-CSI operator from the OperatorHub. Follow the instructions shown by the "Install" button. When using this approach, the operator itself always runs with default parameters, in particular log output in "text" format.

Installing the operator from YAML

Alternatively, the you can install the operator manually from YAML files. First install the PmemCSIDeployment CRD:

$ kubectl create -f https://github.com/intel/pmem-csi/raw/devel/deploy/crd/pmem-csi.intel.com_pmemcsideployments.yaml

Then install the PMEM-CSI operator itself:

$ kubectl create -f https://github.com/intel/pmem-csi/raw/devel/deploy/operator/pmem-csi-operator.yaml

The operator gets deployed in a namespace called 'pmem-csi' which gets created by that YAML file.

WARNING: This YAML file cannot be used to stop just the operator while keeping the PMEM-CSI deployments running. That's because something like kubectl delete -f pmem-csi-operator.yaml will delete the pmem-csi namespace which then also causes all PMEM-CSI deployments that might have been created in that namespace to be deleted.

Create a driver deployment

Once the operator is installed and running, it is ready to handle PmemCSIDeployment objects in the pmem-csi.intel.com API group. Refer to the PmemCSIDeployment CRD API for a complete list of supported properties.

Here is a minimal example driver deployment created with a custom resource:

$ kubectl create -f - <<EOF
apiVersion: pmem-csi.intel.com/v1beta1
kind: PmemCSIDeployment
metadata:
  name: pmem-csi.intel.com
spec:
  deviceMode: lvm
  nodeSelector:
    feature.node.kubernetes.io/memory-nv.dax: "true"
EOF

This uses the same pmem-csi.intel.com driver name as the YAML files in deploy and the node label created by NFD (see the hardware installation and setup section.

Once the above deployment installation is successful, we can see all the driver pods in Running state:

$ kubectl get pmemcsideployments
NAME                 DEVICEMODE   NODESELECTOR   IMAGE   STATUS   AGE
pmem-deployment      lvm                                 Running  50s

$ kubectl describe pmemcsideployment/pmem-csi.intel.com
Name:         pmem-csi.intel.com
Namespace:
Labels:       <none>
Annotations:  <none>
API Version:  pmem-csi.intel.com/v1beta1
Kind:         PmemCSIDeployment
Metadata:
  Creation Timestamp:  2020-10-07T07:31:58Z
  Generation:          1
  Managed Fields:
    API Version:  pmem-csi.intel.com/v1beta1
    Fields Type:  FieldsV1
    fieldsV1:
      f:spec:
        .:
        f:deviceMode:
        f:nodeSelector:
          .:
          f:storage:
    Manager:      kubectl-create
    Operation:    Update
    Time:         2020-10-07T07:31:58Z
    API Version:  pmem-csi.intel.com/v1beta1
    Fields Type:  FieldsV1
    fieldsV1:
      f:status:
        .:
        f:conditions:
        f:driverComponents:
        f:lastUpdated:
        f:phase:
    Manager:         pmem-csi-operator
    Operation:       Update
    Time:            2020-10-07T07:32:22Z
  Resource Version:  1235740
  Self Link:         /apis/pmem-csi.intel.com/v1beta1/pmemcsideployments/pmem-csi.intel.com
  UID:               d8635490-53fa-4eec-970d-cd4c76f53b23
Spec:
  Device Mode:  lvm
  Node Selector:
    Storage:  pmem
Status:
  Conditions:
    Last Update Time:  2020-10-07T07:32:00Z
    Reason:            Driver certificates are available.
    Status:            True
    Type:              CertsReady
    Last Update Time:  2020-10-07T07:32:02Z
    Reason:            Driver deployed successfully.
    Status:            True
    Type:              DriverDeployed
  Driver Components:
    Component:     Controller
    Last Updated:  2020-10-08T07:45:13Z
    Reason:        1 instance(s) of controller driver is running successfully
    Status:        Ready
    Component:     Node
    Last Updated:  2020-10-08T07:45:11Z
    Reason:        All 3 node driver pod(s) running successfully
    Status:        Ready
  Last Updated:    2020-10-07T07:32:21Z
  Phase:           Running
  Reason:          All driver components are deployed successfully
Events:
  Type    Reason         Age   From               Message
  ----    ------         ----  ----               -------
  Normal  NewDeployment  58s   pmem-csi-operator  Processing new driver deployment
  Normal  Running        39s   pmem-csi-operator  Driver deployment successful

$ kubectl get pod -n pmem-csi
NAME                               READY   STATUS    RESTARTS   AGE
pmem-csi-intel-com-controller-0    2/2     Running   0          51s
pmem-csi-intel-com-node-4x7cv      2/2     Running   0          50s
pmem-csi-intel-com-node-6grt6      2/2     Running   0          50s
pmem-csi-intel-com-node-msgds      2/2     Running   0          51s
pmem-csi-operator-749c7c7c69-k5k8n 1/1     Running   0          3m

By default, the operator creates the needed private keys and certificates required for running the driver as described in the driver security section. Those certificates are generated by the operator using a self-signed CA. This can be overridden with custom keys and certificates by using appropriate fields in the PmemCSIDeployment specification. These encoded certificates and private keys are made available to driver pods via Kubernetes secrets by the operator.

NOTE: A production deployment that is not supposed to depend on the operator's self-signed CA instead must provide the certificates generated from a trusted certificate authority.

Install from source

• Get source code

PMEM-CSI uses Go modules and thus can be checked out and (if that should be desired) built anywhere in the filesystem. Pre-built container images are available and thus users don't need to build from source, but they may need some additional files for the following sections. To get the source code, use:

$ git clone https://github.com/intel/pmem-csi

• Choose a namespace

By default, setting up certificates as described in the next step will automatically create a pmem-csi namespace if it does not exist yet. Later the driver will be installed in that namespace.

This can be changed by:

• setting the TEST_DRIVER_NAMESPACE env variable to a different name when invoking setup-ca-kubernetes.sh and

• modifying the deployment with kustomize as explained below.

• Set up certificates

Certificates are required as explained in Security for running the PMEM-CSI scheduler extender and webhook. If those are not used, then certificate creation can be skipped. However, the YAML deployment files always create the PMEM-CSI controller StatefulSet which needs the certificates. Without them, the pmem-csi-intel-com-controller-0 pod cannot start, so it is recommended to create certificates or customize the deployment so that this StatefulSet is not created.

Certificates can be created by running the ./test/setup-ca-kubernetes.sh script for your cluster. This script requires "cfssl" tools which can be downloaded. These are the steps for manual set-up of certificates:

• Download cfssl tools

$ curl -L https://pkg.cfssl.org/R1.2/cfssl_linux-amd64 -o _work/bin/cfssl --create-dirs
$ curl -L https://pkg.cfssl.org/R1.2/cfssljson_linux-amd64 -o _work/bin/cfssljson --create-dirs
$ chmod a+x _work/bin/cfssl _work/bin/cfssljson

• Run certificates set-up script

$ KUBCONFIG="<<your cluster kubeconfig path>>" PATH="$PWD/_work/bin:$PATH" ./test/setup-ca-kubernetes.sh

• Deploy the driver to Kubernetes

The deploy/kubernetes-<kubernetes version> directory contains pmem-csi*.yaml files which can be used to deploy the driver on that Kubernetes version. The files in the directory with the highest Kubernetes version might also work for more recent Kubernetes releases. All of these deployments use images published by Intel on Docker Hub.

For each Kubernetes version, four different deployment variants are provided:

• direct or lvm: one uses direct device mode, the other LVM device mode.
• testing: the variants with testing in the name enable debugging features and shouldn't be used in production.

For example, to deploy for production with LVM device mode onto Kubernetes 1.18, use:

$ kubectl create -f deploy/kubernetes-1.18/pmem-csi-lvm.yaml

The PMEM-CSI scheduler extender and webhook are not enabled in this basic installation. See below for instructions about that.

These variants were generated with kustomize. kubectl >= 1.14 includes some support for that. The sub-directories of deploy/kustomize-<kubernetes version> can be used as bases for kubectl kustomize. For example:

• Change namespace:

  $ mkdir -p my-pmem-csi-deployment
  $ cat >my-pmem-csi-deployment/kustomization.yaml <<EOF
  namespace: pmem-driver
  bases:
    - ../deploy/kubernetes-1.18/lvm
  EOF
  $ kubectl create --kustomize my-pmem-csi-deployment

• Configure how much PMEM is used by PMEM-CSI for LVM (see Namespace modes in LVM device mode):

  $ mkdir -p my-pmem-csi-deployment
  $ cat >my-pmem-csi-deployment/kustomization.yaml <<EOF
  bases:
    - ../deploy/kubernetes-1.18/lvm
  patchesJson6902:
    - target:
        group: apps
        version: v1
        kind: DaemonSet
        name: pmem-csi-node
        namespace: pmem-csi
      path: lvm-parameters-patch.yaml
  EOF
  $ cat >my-pmem-csi-deployment/lvm-parameters-patch.yaml <<EOF
  # pmem-driver is in the container #0. Append arguments at the end.
  - op: add
    path: /spec/template/spec/containers/0/args/-
    value: "-pmemPercentage=90"
  EOF
  $ kubectl create --kustomize my-pmem-csi-deployment

• Wait until all pods reach 'Running' status

$ kubectl get pods -n pmem-csi
NAME                    READY   STATUS    RESTARTS   AGE
pmem-csi-intel-com-node-8kmxf     2/2     Running   0          3m15s
pmem-csi-intel-com-node-bvx7m     2/2     Running   0          3m15s
pmem-csi-intel-com-controller-0   2/2     Running   0          3m15s
pmem-csi-intel-com-node-fbmpg     2/2     Running   0          3m15s

After the driver is deployed using one of the methods mentioned above, verify that the node labels have been updated correctly:

$ kubectl get nodes --show-labels

The command output must indicate that every node with PMEM has at least two labels:

pmem-csi.intel.com/node=<NODE-NAME>,storage=pmem

storage=pmem is the label that has to be added manually as described above. When using NFD, the node should have the feature.node.kubernetes.io/memory-nv.dax=true label.

If pmem-csi.intel.com/node is missing, then double-check that the alpha feature gates are enabled, that the CSI driver is running on the node, and that the driver's log output doesn't contain errors.

• Define two storage classes using the driver

$ kubectl create -f deploy/common/pmem-storageclass-ext4.yaml
$ kubectl create -f deploy/common/pmem-storageclass-xfs.yaml

• Provision two PMEM-CSI volumes

$ kubectl create -f deploy/common/pmem-pvc.yaml

• Verify two Persistent Volume Claims have 'Bound' status

$ kubectl get pvc
NAME                STATUS   VOLUME                                     CAPACITY   ACCESS MODES   STORAGECLASS       AGE
pmem-csi-pvc-ext4   Bound    pvc-f70f7b36-6b36-11e9-bf09-deadbeef0100   4Gi        RWO            pmem-csi-sc-ext4   16s
pmem-csi-pvc-xfs    Bound    pvc-f7101fd2-6b36-11e9-bf09-deadbeef0100   4Gi        RWO            pmem-csi-sc-xfs    16s

• Start two applications requesting one provisioned volume each

$ kubectl create -f deploy/common/pmem-app.yaml

These applications each request a mount of a volume, one with ext4-format and another with xfs-format file system.

• Verify two application pods reach 'Running' status

$ kubectl get po my-csi-app-1 my-csi-app-2
NAME           READY   STATUS    RESTARTS   AGE
my-csi-app-1   1/1     Running   0          6m5s
NAME           READY   STATUS    RESTARTS   AGE
my-csi-app-2   1/1     Running   0          6m1s

• Check that applications have a pmem volume mounted with added dax option

$ kubectl exec my-csi-app-1 -- df /data
Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/ndbus0region0fsdax/5ccaa889-551d-11e9-a584-928299ac4b17
                       4062912     16376   3820440   0% /data

$ kubectl exec my-csi-app-2 -- df /data
Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/ndbus0region0fsdax/5cc9b19e-551d-11e9-a584-928299ac4b17
                       4184064     37264   4146800   1% /data

$ kubectl exec my-csi-app-1 -- mount |grep /data
/dev/ndbus0region0fsdax/5ccaa889-551d-11e9-a584-928299ac4b17 on /data type ext4 (rw,relatime,dax)

$ kubectl exec my-csi-app-2 -- mount |grep /data
/dev/ndbus0region0fsdax/5cc9b19e-551d-11e9-a584-928299ac4b17 on /data type xfs (rw,relatime,attr2,dax,inode64,noquota)

Automatic node setup

The expectation is that the scripts which bring up nodes can be adapted to prepare the PMEM for usage by PMEM-CSI as explained earlier. But this might not always be easy.

For the case of converting an existing "raw" namespace to "fsdax" mode there is a possibility to do the conversion through a deployed PMEM-CSI driver:

1. Install PMEM-CSI in LVM mode without preparing nodes. At this point only the central controller pod will run.
2. For each node that has one or more raw namespaces that all need to be converted, set the <driver name>/convert-raw-namespaces label (usually pmem-csi.intel.com/convert-raw-namespaces) to force.
3. This will cause the pods of the pmem-csi-intel-com-node-setup DaemonSet to run on those nodes. Those pods then will convert the namespaces, create the LVM volume group, remove the convert-raw-namespaces label (i.e. the pods will only run once) and add the normal label that enables the PMEM-CSI node driver pods to run.
4. The normal node driver pods start up and then are ready to provision volumes.

WARNING: the raw namespaces will be converted even when they are active. If data was stored on them, it will be lost after the conversion.

The output of a successful conversion will look like this:

I0407 16:24:43.453802       1 main.go:69] Version: v0.9.0-29-g043b4e9c0-dirty
I0407 16:24:43.456707       1 convert.go:78] "raw-namespace-conversion: checking for namespaces"
I0407 16:24:43.457705       1 convert.go:80] "raw-namespace-conversion: checking" bus="{\"dev\":\"ndbus0\",\"dimms\":[{}],\"provider\":\"ACPI.NFIT\",\"regions\":[{}]}"
I0407 16:24:43.458144       1 convert.go:82] "raw-namespace-conversion: checking" region="{\"available_size\":0,\"dev\":\"region0\",\"mappings\":[{}],\"max_available_extent\":0,\"namespaces\":[{}],\"size\":68719476736,\"type\":\"pmem\"}"
I0407 16:24:43.458264       1 convert.go:89] "raw-namespace-conversion: checking" namespace="{\"blockdev\":\"pmem0\",\"dev\":\"namespace0.0\",\"enabled\":true,\"id\":0,\"mode\":\"raw\",\"name\":\"\",\"size\":68719476736,\"uuid\":\"40b5697c-9453-457d-b4b3-789718ac54ab\"}"
I0407 16:24:43.458337       1 convert.go:98] "raw-namespace-conversion: converting raw namespace" namespace="{\"blockdev\":\"pmem0\",\"dev\":\"namespace0.0\",\"enabled\":true,\"id\":0,\"mode\":\"raw\",\"name\":\"\",\"size\":68719476736,\"uuid\":\"40b5697c-9453-457d-b4b3-789718ac54ab\"}"
I0407 16:24:44.077114       1 convert.go:126] "raw-namespace-conversion: setting up volume group" namespace="{\"blockdev\":\"pmem0\",\"dev\":\"namespace0.0\",\"enabled\":false,\"id\":0,\"mode\":\"fsdax\",\"name\":\"\",\"size\":18446744073709551615,\"uuid\":\"00000000-0000-0000-0000-000000000000\"}" VG="ndbus0region0fsdax"
I0407 16:24:44.111153       1 pmd-lvm.go:408] /dev/pmem0: already part of volume group ndbus0region0fsdax
I0407 16:24:44.111352       1 pmd-lvm.go:412] no unused namespace found to add to this group: ndbus0region0fsdax
I0407 16:24:44.111541       1 convert.go:132] "raw-namespace-conversion: converted to fsdax namespace" namespace="{\"blockdev\":\"pmem0\",\"dev\":\"namespace0.0\",\"enabled\":false,\"id\":0,\"mode\":\"fsdax\",\"name\":\"\",\"size\":18446744073709551615,\"uuid\":\"00000000-0000-0000-0000-000000000000\"}" VG="ndbus0region0fsdax"
I0407 16:24:44.111573       1 convert.go:74] "raw-namespace-conversion: successful" converted=1
I0407 16:24:44.127330       1 convert.go:171] "check-pmem: volume group will be used by PMEM-CSI in LVM mode" VG="ndbus0region0fsdax"
I0407 16:24:44.150347       1 convert.go:200] "relabel: change node labels" node="pmem-csi-pmem-govm-master" patch="{\"metadata\":{\"labels\":{\"pmem-csi.intel.com/convert-raw-namespaces\": null, \"feature.node.kubernetes.io/memory-nv.dax\": \"true\"}}}"
I0407 16:24:44.150370       1 pmem-csi-driver.go:325] raw namespace conversion is done, waiting for termination signal
I0407 16:24:45.614284       1 pmem-csi-driver.go:343] Caught signal terminated, terminating.

It terminates once Kubernetes notices that the pod is no longer needed. This usually happens quickly, so a log monitoring solution may be needed to see this output because kubectl logs does not work for pods that were already deleted.

The DaemonSet contains some information which is available longer:

$ kubectl describe daemonsets/pmem-csi-intel-com-node-setup
Name:           pmem-csi-intel-com-node-setup
Selector:       app.kubernetes.io/instance=pmem-csi.intel.com,app.kubernetes.io/name=pmem-csi-node-setup,pmem-csi.intel.com/deployment=lvm-production
Node-Selector:  pmem-csi.intel.com/convert-raw-namespaces=force
Labels:         app.kubernetes.io/component=node-setup
                app.kubernetes.io/instance=pmem-csi.intel.com
                app.kubernetes.io/name=pmem-csi-node-setup
                app.kubernetes.io/part-of=pmem-csi
                pmem-csi.intel.com/deployment=lvm-production
Annotations:    deprecated.daemonset.template.generation: 1
Desired Number of Nodes Scheduled: 0
Current Number of Nodes Scheduled: 0
Number of Nodes Scheduled with Up-to-date Pods: 0
Number of Nodes Scheduled with Available Pods: 0
Number of Nodes Misscheduled: 0
Pods Status:  0 Running / 0 Waiting / 0 Succeeded / 0 Failed
Pod Template:
  Labels:           app.kubernetes.io/component=node-setup
                    app.kubernetes.io/instance=pmem-csi.intel.com
                    app.kubernetes.io/name=pmem-csi-node-setup
                    app.kubernetes.io/part-of=pmem-csi
                    pmem-csi.intel.com/deployment=lvm-production
                    pmem-csi.intel.com/webhook=ignore
  Service Account:  pmem-csi-intel-com-node-setup
  Containers:
   pmem-driver:
    Image:      172.17.42.1:5001/pmem-csi-driver:canary
    Port:       <none>
    Host Port:  <none>
    Command:
      /usr/local/bin/pmem-csi-driver
      -v=3
      -logging-format=text
      -mode=force-convert-raw-namespaces
      -nodeSelector={"storage":"pmem"}
      -nodeid=$(KUBE_NODE_NAME)
...
Events:
  Type    Reason            Age    From                  Message
  ----    ------            ----   ----                  -------
  Normal  SuccessfulCreate  5m47s  daemonset-controller  Created pod: pmem-csi-intel-com-node-setup-fr9b8
  Normal  SuccessfulDelete  5m45s  daemonset-controller  Deleted pod: pmem-csi-intel-com-node-setup-fr9b8

If conversion fails, the pod will exit with an error and then get restarted automatically by Kubernetes to retry the conversion until it succeeds.

It is considered a user error if conversion is requested for a node which has nothing to convert. To make that obvious, the pod will print an error and then exist with an error. That way, the pod continues to exist and the log can be inspected to identify the problem.

Volume parameters

Kubernetes cluster administrators can make persistent volumes available to applications using storage classes, with the behavior of the volumes determined by StorageClass Parameters.

In addition to the normal parameters defined by Kubernetes, PMEM-CSI supports the following custom parameters in a storage class:

key	meaning	optional	values
eraseAfter	Clear all data by overwriting with zeroes after use and before deleting the volume	Yes	true (default), false
kataContainers	Prepare volume for use with DAX in Kata Containers.	Yes	false/0/f/FALSE (default), true/1/t/TRUE

Kata Containers support

Kata Containers support gets enabled via the kataContainers storage class parameter. PMEM-CSI then creates a filesystem inside a partition inside a file. When such a volume is used inside Kata Containers, the Kata Containers runtime makes sure that the filesystem is mounted on an emulated NVDIMM device with full DAX support.

On the host, PMEM-CSI will try to mount through a loop device with -o dax but proceed without -o dax when the kernel does not support that. Currently Linux up to and including 5.4 do not support it and it is unclear when that support will be added In other words, on the host such volumes are usable, but only without DAX.

When disabled, volumes support DAX on the host and are usable without DAX inside Kata Containers.

Raw block volumes are only supported with kataContainers: false. Attempts to create them with kataContainers: true are rejected.

At the moment (= Kata Containers 1.11.0-rc0), only Kata Containers with QEMU enable the special support for such volumes. Without QEMU or with older releases of Kata Containers, the volume is still usable through the normal remote filesystem support (9p or virtio-fs). Support for Cloud Hypervisor is in progress.

With Kata Containers for QEMU, the VM must be configured appropriately to allow adding the PMEM volumes to their address space. This can be done globally by setting the memory_offset in the configuration-qemu.toml file or per-pod by setting the io.katacontainers.config.hypervisor.memory_offset label in the pod meta data. In both cases, the value has to be large enough for all PMEM volumes used by the pod, otherwise pod creation will fail with an error similar to this:

Error: container create failed: QMP command failed: not enough space, currently 0x8000000 in use of total space for memory devices 0x3c100000

The examples for usage of Kata Containers with ephemeral and persistent volumes use the pod label. They assume that the kata-qemu runtime class is installed.

For the QEMU test cluster, setup-kata-containers.sh can be used to install Kata Containers. However, this currently only works on Clear Linux because on Fedora, the Docker container runtime is used and Kata Containers does not support that one.

Ephemeral inline volumes

Kubernetes CSI specific

This is the original implementation of ephemeral inline volumes for CSI drivers in Kubernetes. It is currently available as a beta feature in Kubernetes.

Volume requests embedded in the pod spec are provisioned as ephemeral volumes. The volume request could use below fields as volumeAttributes:

key	meaning	optional	values
size	Size of the requested ephemeral volume as Kubernetes memory string ("1Mi" = 1024*1024 bytes, "1e3K = 1000000 bytes)	No
eraseAfter	Clear all data by overwriting with zeroes after use and before deleting the volume	Yes	true (default), false
kataContainers	Prepare volume for use in Kata Containers.	Yes	false/0/f/FALSE (default), true/1/t/TRUE

Try out ephemeral volume usage with the provided example application.

Generic

This approach was introduced in Kubernetes 1.19 with the goal of using them for PMEM-CSI instead of the older approach. In contrast CSI ephemeral inline volumes, no changes are needed in CSI drivers, so PMEM-CSI already fully supports this if the cluster has the feature enabled. See pmem-app-generic-ephemeral.yaml for an example.

When using generic ephemeral inline volumes together with storage capacity tracking, the PMEM-CSI scheduler extensions are not needed anymore.

Raw block volumes

Applications can use volumes provisioned by PMEM-CSI as raw block devices. Such volumes use the same "fsdax" namespace mode as filesystem volumes and therefore are block devices. That mode only supports dax (= mmap(MAP_SYNC)) through a filesystem. Pages mapped on the raw block device go through the Linux page cache. Applications have to format and mount the raw block volume themselves if they want dax. The advantage then is that they have full control over that part.

For provisioning a PMEM volume as raw block device, one has to create a PersistentVolumeClaim with volumeMode: Block. See example PVC and application for usage reference.

That example demonstrates how to handle some details:

• mkfs.ext4 needs -b 4096 to produce volumes that support dax; without it, the automatic block size detection may end up choosing an unsuitable value depending on the volume size.
• Kubernetes bug #85624 must be worked around to format and mount the raw block device.

Enable scheduler extensions

The PMEM-CSI scheduler extender and admission webhook are provided by the PMEM-CSI controller. They need to be enabled during deployment via the --schedulerListen=[<listen address>]:<port> parameter. The listen address is optional and can be left out. The port is where a HTTPS server will run.

The controller needs TLS certificates which must be created in advance. The YAML files expects them in a secret called pmem-csi-intel-com-controller-secret and will not work without one. The operator is more flexible and creates a driver without the controller by default. This can be changed by setting the controllerTLSSecret field in the PmemCSIDeployment API.

That secret must contain the following data items:

• ca.crt: root CA certificate
• tls.key: secret key of the webhook
• tls.crt: public key of the webhook

The webhook certificate must include host names that match how the webhooks are going to be called by the kube-apiserver (i.e. pmem-csi-intel-com-scheduler.pmem-csi.svc for a deployment with the pmem-csi.intel.com driver name in the pmem-csi namespace) and by the kube-scheduler (might be the same service name, through some external load balancer or 127.0.0.1 when using the node port workaround described below).

To enable the PMEM-CSI scheduler extender, a configuration file and an additional --config parameter for kube-scheduler must be added to the cluster control plane, or, if there is already such a configuration file, one new entry must be added to the extenders array. A full example is presented below.

The kube-scheduler must be able to connect to the PMEM-CSI controller via the urlPrefix in its configuration. In some clusters it is possible to use cluster DNS and thus a symbolic service name. If that is the case, then deploy the scheduler service as-is and use https://pmem-csi-scheduler.default.svc as urlPrefix. If the PMEM-CSI driver is deployed in a namespace, replace default with the name of that namespace.

In a cluster created with kubeadm, kube-scheduler is unable to use cluster DNS because the pod it runs in is configured with hostNetwork: true and without dnsPolicy. Therefore the cluster DNS servers are ignored. There also is no special dialer as in other clusters. As a workaround, the PMEM-CSI service can be exposed via a fixed node port like 32000 on all nodes. Then https://127.0.0.1:32000 needs to be used as urlPrefix. Here's how the service can be created with that node port:

$ mkdir my-scheduler

$ cat >my-scheduler/kustomization.yaml <<EOF
bases:
  - ../deploy/kustomize/scheduler
patchesJson6902:
  - target:
      version: v1
      kind: Service
      name: pmem-csi-intel-com-scheduler
      namespace: pmem-csi
    path: node-port-patch.yaml
EOF

$ cat >my-scheduler/node-port-patch.yaml <<EOF
- op: add
  path: /spec/ports/0/nodePort
  value: 32000
- op: add
  path: /spec/type
  value: NodePort
EOF

$ kubectl create --kustomize my-scheduler

When the node port is not needed, the scheduler service can be created directly with:

kubectl create --kustomize deploy/kustomize/scheduler

How to (re)configure kube-scheduler depends on the cluster. With kubeadm it is possible to set all necessary options in advance before creating the master node with kubeadm init. A running cluster can be modified with kubeadm upgrade.

One additional complication with kubeadm is that kube-scheduler by default doesn't trust any root CA. The following kubeadm config file solves this together with enabling the scheduler configuration by bind-mounting the root certificate that was used to sign the certificate used by the scheduler extender into the location where the Go runtime will find it. It works for Kubernetes <= 1.18:

$ sudo mkdir -p /var/lib/scheduler/
$ sudo cp _work/pmem-ca/ca.pem /var/lib/scheduler/ca.crt

# https://github.com/kubernetes/kubernetes/blob/52d7614a8ca5b8aebc45333b6dc8fbf86a5e7ddf/staging/src/k8s.io/kube-scheduler/config/v1alpha1/types.go#L38-L107
$ sudo sh -c 'cat >/var/lib/scheduler/scheduler-policy.cfg' <<EOF
{
  "kind" : "Policy",
  "apiVersion" : "v1",
  "extenders" :
    [{
      "urlPrefix": "https://<service name or IP>:<port>",
      "filterVerb": "filter",
      "prioritizeVerb": "prioritize",
      "nodeCacheCapable": true,
      "weight": 1,
      "managedResources":
      [{
        "name": "pmem-csi.intel.com/scheduler",
        "ignoredByScheduler": true
      }]
    }]
}
EOF

# https://github.com/kubernetes/kubernetes/blob/52d7614a8ca5b8aebc45333b6dc8fbf86a5e7ddf/staging/src/k8s.io/kube-scheduler/config/v1alpha1/types.go#L38-L107
$ sudo sh -c 'cat >/var/lib/scheduler/scheduler-config.yaml' <<EOF
apiVersion: kubescheduler.config.k8s.io/v1alpha1
kind: KubeSchedulerConfiguration
schedulerName: default-scheduler
algorithmSource:
  policy:
    file:
      path: /var/lib/scheduler/scheduler-policy.cfg
clientConnection:
  # This is where kubeadm puts it.
  kubeconfig: /etc/kubernetes/scheduler.conf
EOF

$ cat >kubeadm.config <<EOF
apiVersion: kubeadm.k8s.io/v1beta1
kind: ClusterConfiguration
scheduler:
  extraVolumes:
    - name: config
      hostPath: /var/lib/scheduler
      mountPath: /var/lib/scheduler
      readOnly: true
    - name: cluster-root-ca
      hostPath: /var/lib/scheduler/ca.crt
      mountPath: /etc/ssl/certs/ca.crt
      readOnly: true
  extraArgs:
    config: /var/lib/scheduler/scheduler-config.yaml
EOF

$ kubeadm init --config=kubeadm.config

In Kubernetes 1.19, the configuration API of the scheduler changed. The corresponding command for Kubernetes >= 1.19 are:

$ sudo mkdir -p /var/lib/scheduler/
$ sudo cp _work/pmem-ca/ca.pem /var/lib/scheduler/ca.crt

# https://github.com/kubernetes/kubernetes/blob/1afc53514032a44d091ae4a9f6e092171db9fe10/staging/src/k8s.io/kube-scheduler/config/v1beta1/types.go#L44-L96
$ sudo sh -c 'cat >/var/lib/scheduler/scheduler-config.yaml' <<EOF
apiVersion: kubescheduler.config.k8s.io/v1beta1
kind: KubeSchedulerConfiguration
clientConnection:
  # This is where kubeadm puts it.
  kubeconfig: /etc/kubernetes/scheduler.conf
extenders:
- urlPrefix: https://127.0.0.1:<service name or IP>:<port>
  filterVerb: filter
  prioritizeVerb: prioritize
  nodeCacheCapable: true
  weight: 1
  managedResources:
  - name: pmem-csi.intel.com/scheduler
    ignoredByScheduler: true
EOF

$ cat >kubeadm.config <<EOF
apiVersion: kubeadm.k8s.io/v1beta1
kind: ClusterConfiguration
scheduler:
  extraVolumes:
    - name: config
      hostPath: /var/lib/scheduler
      mountPath: /var/lib/scheduler
      readOnly: true
    - name: cluster-root-ca
      hostPath: /var/lib/scheduler/ca.crt
      mountPath: /etc/ssl/certs/ca.crt
      readOnly: true
  extraArgs:
    config: /var/lib/scheduler/scheduler-config.yaml
EOF

$ kubeadm init --config=kubeadm.config

It is possible to stop here without enabling the pod admission webhook. To enable also that, continue as follows.

First of all, it is recommended to exclude all system pods from passing through the web hook. This ensures that they can still be created even when PMEM-CSI is down:

$ kubectl label ns kube-system pmem-csi.intel.com/webhook=ignore

This special label is configured in the provided web hook definition. On Kubernetes >= 1.15, it can also be used to let individual pods bypass the webhook by adding that label. The CA gets configured explicitly, which is supported for webhooks.

$ mkdir my-webhook

$ cat >my-webhook/kustomization.yaml <<EOF
bases:
  - ../deploy/kustomize/webhook
patchesJson6902:
  - target:
      group: admissionregistration.k8s.io
      version: v1beta1
      kind: MutatingWebhookConfiguration
      name: pmem-csi-intel-com-hook
    path: webhook-patch.yaml
EOF

$ cat >my-webhook/webhook-patch.yaml <<EOF
- op: replace
  path: /webhooks/0/clientConfig/caBundle
  value: $(base64 -w 0 _work/pmem-ca/ca.pem)
EOF

$ kubectl create --kustomize my-webhook

Storage capacity tracking

Kubernetes 1.19 introduces support for publishing and using storage capacity information for pod scheduling. PMEM-CSI must be deployed differently to use this feature:

• external-provisioner must be told to publish storage capacity information via command line arguments.
• A flag in the CSI driver information must be set for the Kubernetes scheduler, otherwise it ignores that information when considering pods with unbound volume.

Because the CSIStorageCapacity feature is still alpha in 1.19 and driver deployment would fail on a cluster without support for it, none of the normal deployment files nor the operator enable that. Instead, special kustomize variants are provided in deploy/kubernetes-1.19-alpha*.

They can be used for example in the QEMU test cluster with:

$ TEST_KUBERNETES_VERSION=1.19 make start
...
$ TEST_KUBERNETES_FLAVOR=-alpha test/setup-deployment.sh
INFO: deploying from /nvme/gopath/src/github.com/intel/pmem-csi/deploy/kubernetes-1.19-alpha/lvm/testing
...

Metrics support

Metrics support is controlled by command line options of the PMEM-CSI driver binary and of the CSI sidecars. Annotations and named container ports make it possible to discover these data scraping endpoints. The metrics kustomize base adds all of that to the pre-generated deployment files. The operator also enables the metrics support.

Access to metrics data is not restricted (no TLS, no client authorization) because the metrics data is not considered confidential and access control would just make client configuration unnecessarily complex.

Metrics data

PMEM-CSI exposes metrics data about the Go runtime, Prometheus, CSI method calls, and PMEM-CSI:

Name	Type	Explanation
build_info	gauge	A metric with a constant '1' value labeled by version.
scheduler_request_duration_seconds	histogram	Latencies for PMEM-CSI scheduler HTTP requests by operation ("mutate", "filter", "status") and method ("post").
scheduler_in_flight_requests	gauge	Currently pending PMEM-CSI scheduler HTTP requests.
scheduler_requests_total	counter	Number of HTTP requests to the PMEM-CSI scheduler, regardless of operation and method.
scheduler_response_size_bytes	histogram	Histogram of response sizes for PMEM-CSI scheduler requests, regardless of operation and method.
csi_[sidecar|plugin]_operations_seconds	histogram	gRPC call duration and error code, for sidecar to driver (aka plugin) communication.
go_*		Go runtime information
pmem_amount_available	gauge	Remaining amount of PMEM on the host that can be used for new volumes.
pmem_amount_managed	gauge	Amount of PMEM on the host that is managed by PMEM-CSI.
pmem_amount_max_volume_size	gauge	The size of the largest PMEM volume that can be created.
pmem_amount_total	gauge	Total amount of PMEM on the host.
process_*		Process information
promhttp_metric_handler_requests_in_flight	gauge	Current number of scrapes being served.
promhttp_metric_handler_requests_total	counter	Total number of scrapes by HTTP status code.

This list is tentative and may still change as long as metrics support is alpha. To see all available data, query a container. Different containers provide different data. For example, the controller provides:

$ kubectl port-forward pmem-csi-intel-com-controller-0 10010
Forwarding from 127.0.0.1:10010 -> 10010
Forwarding from [::1]:10010 -> 10010

And in another shell:

$ curl --silent http://localhost:10010/metrics | grep '# '
# HELP build_info A metric with a constant '1' value labeled by version.
# TYPE build_info gauge
...

Prometheus example

An extension of the scrape config is necessary for Prometheus. When deploying Prometheus via Helm, that file can be added to the default configuration with the -f parameter. The following example works for the QEMU-based cluster and Helm v3.1.2. In a real production deployment, some kind of persistent storage should be provided. The URL can be used instead of the file name, too.

$ helm install prometheus stable/prometheus \
     --set alertmanager.persistentVolume.enabled=false,server.persistentVolume.enabled=false \
     -f deploy/prometheus.yaml
NAME: prometheus
LAST DEPLOYED: Tue Aug 18 18:04:27 2020
NAMESPACE: default
STATUS: deployed
REVISION: 1
TEST SUITE: None
NOTES:
The Prometheus server can be accessed via port 80 on the following DNS name from within your cluster:
prometheus-server.default.svc.cluster.local


Get the Prometheus server URL by running these commands in the same shell:
  export POD_NAME=$(kubectl get pods --namespace default -l "app=prometheus,component=server" -o jsonpath="{.items[0].metadata.name}")
  kubectl --namespace default port-forward $POD_NAME 9090
#################################################################################
######   WARNING: Persistence is disabled!!! You will lose your data when   #####
######            the Server pod is terminated.                             #####
#################################################################################

...

After running this kubectl port-forward command, it is possible to access the Prometheus web interface and run some queries there. Here are some examples for the QEMU test cluster with two volumes created on node pmem-csi-pmem-govm-worker2.

Available PMEM as percentage:

pmem_amount_available / pmem_amount_managed

Result variable	Value	Tags
none	0.7332986065893997	instance = 10.42.0.1:10010
		job = pmem-csi-containers
		kubernetes_namespace = default
		kubernetes_pod_container_name = pmem-driver
		kubernetes_pod_name = pmem-csi-node-dfkrw
		kubernetes_pod_node_name = pmem-csi-pmem-govm-worker2
		node = pmem-csi-pmem-govm-worker2
	1	instance = 10.36.0.1:10010
		job = pmem-csi-containers
		kubernetes_namespace = default
		kubernetes_pod_container_name = pmem-driver
		kubernetes_pod_name = pmem-csi-node-z5vnp
		kubernetes_pod_node_name pmem-csi-pmem-govm-worker3
		node = pmem-csi-pmem-govm-worker3
	1	instance = 10.44.0.1:10010
		job = pmem-csi-containers
		kubernetes_namespace = default
		kubernetes_pod_container_name = pmem-driver
		kubernetes_pod_name = pmem-csi-node-zzmsd
		kubernetes_pod_node_name = pmem-csi-pmem-govm-worker1
		node = pmem-csi-pmem-govm-worker1

Number of CreateVolume calls in nodes:

pmem_csi_node_operations_seconds_count{method_name="/csi.v1.Controller/CreateVolume"}

Result variable	Value	Tags
pmem_csi_node_operations_seconds_count	2	driver_name = pmem-csi.intel.com
		grpc_status_code = OK
		instance = 10.42.0.1:10010
		job = pmem-csi-containers
		kubernetes_namespace = default
		kubernetes_pod_container_name = pmem-driver
		kubernetes_pod_name = pmem-csi-node-dfkrw
		kubernetes_pod_node_name = pmem-csi-pmem-govm-worker2
		method_name = /csi.v1.Controller/CreateVolume
		node = pmem-csi-pmem-govm-worker2

PMEM-CSI Deployment CRD

TODO update operator

PmemCSIDeployment is a cluster-scoped Kubernetes resource in the pmem-csi.intel.com API group. It describes how a PMEM-CSI driver instance is to be created.

The operator will create objects in the namespace in which the operator itself runs if the object type is namespaced.

The name of the deployment object is also used as CSI driver name. This ensures that the name is unique and immutable. However, name clashes with other CSI drivers are still possible, so the name should meet the CSI requirements:

• domain name notation format, including a unique top-level domain
• 63 characters or less, beginning and ending with an alphanumeric character ([a-z0-9A-Z]) with dashes (-), dots (.), and alphanumerics between.

The name is also used as prefix for the names of all objects created for the deployment and for the local /var/lib/<name> state directory on each node.

NOTE: Starting from release v0.9.0 reconciling of the Deployment CRD in pmem-csi.intel.com/v1alpha1 API group is not supported by the PMEM-CSI operator anymore. Such resources in the cluster must be migrated manually to new the PmemCSIDeployment API.

The current API for PmemCSIDeployment resources is:

PmemCSIDeployment

Field	Type	Description
apiVersion	string	pmem-csi.intel.com/v1beta1
kind	string	PmemCSIDeployment
metadata	ObjectMeta	Object metadata, name used for CSI driver and as prefix for sub-objects
spec	DeploymentSpec	Specification of the desired behavior of the deployment

DeploymentSpec

Below specification fields are valid in all API versions unless noted otherwise in the description.

The default values are used by the operator when no value is set for a field explicitly. Those defaults can change over time and are not part of the API specification.

Field	Type	Description	Default Value
image	string	PMEM-CSI docker image name used for the deployment	the same image as the operator1
provisionerImage	string	CSI provisioner docker image name	latest external provisioner stable release image2
nodeRegistrarImage	string	CSI node driver registrar docker image name	latest node driver registrar stable release image2
pullPolicy	string	Docker image pull policy. either one of Always, Never, IfNotPresent	IfNotPresent
logLevel	integer	PMEM-CSI driver logging level	3
logFormat	text	log output format	"text" or "json" 3
deviceMode	string	Device management mode to use. Supports one of lvm or direct	lvm
controllerTLSSecret	string	Name of an existing secret in the driver's namespace which contains ca.crt, tls.crt and tls.key data for the scheduler extender and pod mutation webhook. A controller is started if (and only if) this secret is specified.	empty
mutatePods	Always/Try/Never	Defines how a mutating pod webhook is configured if a controller is started. The field is ignored if the controller is not enabled. "Never" disables pod mutation. "Try" configured it so that pod creation is allowed to proceed even when the webhook fails. "Always" requires that the webhook gets invoked successfully before creating a pod.	Try
schedulerNodePort	If non-zero, the scheduler service is created as a NodeService with that fixed port number. Otherwise that service is created as a cluster service. The number must be from the range reserved by Kubernetes for node ports. This is useful if the kube-scheduler cannot reach the scheduler extender via a cluster service.	0
controllerResources	ResourceRequirements	Describes the compute resource requirements for controller pod. 4Deprecated and only available in v1alpha1.
nodeResources	ResourceRequirements	Describes the compute resource requirements for the pods running on node(s). 4Deprecated and only available in v1alpha1.
controllerDriverResources	ResourceRequirements	Describes the compute resource requirements for controller driver container running on master node. Available since v1beta1.
nodeDriverResources	ResourceRequirements	Describes the compute resource requirements for the driver container running on worker node(s). Available since v1beta1.
provisionerResources	ResourceRequirements	Describes the compute resource requirements for the external provisioner sidecar container. Available since v1beta1.
nodeRegistrarResources	ResourceRequirements	Describes the compute resource requirements for the driver registrar sidecar container running on worker node(s). Available since v1beta1.
registryCert	string	Encoded tls certificate signed by a certificate authority used for driver's controller registry server	generated by operator self-signed CA
nodeControllerCert	string	Encoded tls certificate signed by a certificate authority used for driver's node controllers	generated by operator self-signed CA
registryKey	string	Encoded RSA private key used for signing by registryCert	generated by the operator
nodeControllerKey	string	Encoded RSA private key used for signing by nodeControllerCert	generated by the operator
caCert	string	Certificate of the CA by which the registryCert and controllerCert are signed	self-signed certificate generated by the operator
nodeSelector	string map	Labels to use for selecting Nodes on which PMEM-CSI driver should run.	{ "storage": "pmem" }
pmemPercentage	integer	Percentage of PMEM space to be used by the driver on each node. This is only valid for a driver deployed in lvm mode. This field can be modified, but by that time the old value may have been used already. Reducing the percentage is not supported.	100
labels	string map	Additional labels for all objects created by the operator. Can be modified after the initial creation, but removed labels will not be removed from existing objects because the operator cannot know which labels it needs to remove and which it has to leave in place.
kubeletDir	string	Kubelet's root directory path	/var/lib/kubelet

¹ To use the same container image as default driver image the operator pod must set with below environment variables with appropriate values:

• POD_NAME: Name of the operator pod. Namespace of the pod could be figured out by the operator.
• OPERATOR_NAME: Name of the operator container. If not set, defaults to "pmem-csi-operator"

² Image versions depend on the Kubernetes release. The operator dynamically chooses suitable image versions. Users have to take care of that themselves when overriding the values.

³ In PMEM-CSI 0.9.0, "json" output is only available for the PMEM-CSI container. The sidecars are still producing plain text messages. This may change in the future. Also, the migration from formatted log messages (= printf style) to structured log messages (message plus key/value pairs) is not complete.

⁴ Pod level resource requirements (nodeResources and controllerResources) are deprecated in favor of per-container resource requirements (nodeDriverResources, nodeRegistrarResources, controllerDriverResources and provisionerResources).

WARNING: although all fields can be modified and changes will be propagated to the deployed driver, not all changes are safe. In particular, changing the deviceMode will not work when there are active volumes.

DeploymentStatus

A PMEM-CSI Deployment's status field is a DeploymentStatus object, which carries the detailed state of the driver deployment. It is comprised of deployment conditions, driver component status, and a phase field. The phase of a PMEM-CSI deployment is a high-level summary of where the the PmemCSIDployment is in its lifecycle.

The possible phase values and their meaning are as below:

Value	Meaning
empty string	A new deployment.
Running	The operator has determined that the driver is usable1.
Failed	For some reason, the PmemCSIDeployment failed and cannot be progressed. The failure reason is placed in the DeploymentStatus.Reason field.

¹ This check has not been implemented yet. Instead, the deployment goes straight to Running after creating sub-resources.

Deployment Conditions

PMEM-CSI DeploymentStatus has an array of conditions through which the PMEM-CSI Deployment has or has not passed. Below are the possible condition types and their meanings:

Condition type	Meaning
CertsReady	Driver certificates/secrets are available.
CertsVerified	Verified that the provided certificates are valid.
DriverDeployed	All the componentes required for the PMEM-CSI deployment have been deployed.

Driver component status

PMEM-CSI DeploymentStatus has an array of components of type DriverStatus in which the operator records the brief driver components status. This is useful to know if all the driver instances of a deployment are ready. Below are the fields and their meanings of DriverStatus:

Field	Meaning
component	Represents the driver component type; one of Controller or Node.
status	Represents the state of the component; one of Ready or NotReady. Component becomes Ready if all the instances of the driver component are running. Otherwise, NotReady.
reason	A brief message that explains why the component is in this state.
lastUpdateTime	Time at which the status updated.

Deployment Events

The PMEM-CSI operator posts events on the progress of a PmemCSIDeployment. If the deployment is in the Failed state, then one can look into the event(s) using kubectl describe on that deployment for the detailed failure reason.

Note on multiple deployments

Though the operator allows running multiple PMEM-CSI driver deployments, one has to take extreme care of such deployments by ensuring that not more than one driver ends up running on the same node(s). Nodes on which a PMEM-CSI driver could run can be configured by using nodeSelector property of DeploymentSpec.

Operator metrics data

PMEM-CSI operator exposes below metrics data about active PmemCSIDeployment custom resources and it's sub-object in addition to the metrics data provided by the controller-runtime:

Name	Type	Explanation
pmem_csi_deployment_reconcile	counter	Counter that gets incremented on each time a PmemCSIDeployment CR gone through a reconcile loop, labeled with the deployment name and uid.
pmem_csi_deployment_sub_resource_created_at	gauge	Timestamp at which a sub resource of the PmemCSIDeployment CR was created by the operator. Labeled by resource details ("name, "namespace", "group", "version", "kind", "uid", "ownedBy").
pmem_csi_deployment_sub_resource_updated_at	gauge	Timestamp at which a sub resource of the PmemCSIDeployment CR was updated by the operator. Labeled by resource details ("name, "namespace", "group", "version", "kind", "uid", "ownedBy").

Filing issues and contributing

Report a bug by filing a new issue.

Before making your first contribution, be sure to read the development documentation for guidance on code quality and branches.

Contribute by opening a pull request.

Learn about pull requests.

Reporting a Potential Security Vulnerability: If you have discovered potential security vulnerability in PMEM-CSI, please send an e-mail to [email protected]. For issues related to Intel Products, please visit Intel Security Center.

It is important to include the following details:

• The projects and versions affected
• Detailed description of the vulnerability
• Information on known exploits

Vulnerability information is extremely sensitive. Please encrypt all security vulnerability reports using our PGP key.

A member of the Intel Product Security Team will review your e-mail and contact you to collaborate on resolving the issue. For more information on how Intel works to resolve security issues, see: vulnerability handling guidelines.