OSD tab missing on Flylens 85

[ashleonard207]

Describe the bug

The OSD tab no longer shows up since 10.10 but it works in 10.9. The option to turn it on under the configuration tab is gone as well.

To Reproduce

use a fully set up Flywoo Flylens 85 (it uses the goku f405 hd 1-2s elrs aio v2 flight controller) and plug it into betaflight. Turn on expert mode.

Expected behavior

Even with expert mode enabled the OSD is gone, as well as most of the options under configurations->other features. The only ones left are airmode, inflight_acc_cal, and sofserial.

Configurator version

11.0.0

Flight controller configuration

# name: Voyager 1

# resources
resource BEEPER 1 C13
resource MOTOR 1 B00
resource MOTOR 2 B01
resource MOTOR 3 A03
resource MOTOR 4 A02
resource MOTOR 6 B07
resource MOTOR 7 C09
resource MOTOR 8 C08
resource LED_STRIP 1 A09
resource SERIAL_TX 1 B06
resource SERIAL_TX 2 D05
resource SERIAL_TX 3 B10
resource SERIAL_TX 4 A00
resource SERIAL_TX 6 C06
resource SERIAL_RX 1 A10
resource SERIAL_RX 3 B11
resource SERIAL_RX 4 A01
resource SERIAL_RX 5 D02
resource SERIAL_RX 6 C07
resource I2C_SCL 1 B08
resource I2C_SDA 1 B09
resource LED 1 C14
resource SPI_SCK 1 A05
resource SPI_SCK 3 C10
resource SPI_MISO 1 A06
resource SPI_MISO 3 C11
resource SPI_MOSI 1 A07
resource SPI_MOSI 3 C12
resource ESCSERIAL 1 B08
resource ADC_BATT 1 C03
resource ADC_RSSI 1 C00
resource ADC_CURR 1 C02
resource PINIO 1 D06
resource PINIO 2 B05
resource FLASH_CS 1 B03
resource OSD_CS 1 B14
resource GYRO_EXTI 1 B13
resource GYRO_CS 1 B12
resource USB_DETECT 1 A08

# timer
timer B00 AF2
# pin B00: TIM3 CH3 (AF2)
timer B01 AF2
# pin B01: TIM3 CH4 (AF2)
timer A03 AF1
# pin A03: TIM2 CH4 (AF1)
timer A02 AF1
# pin A02: TIM2 CH3 (AF1)
timer B05 AF2
# pin B05: TIM3 CH2 (AF2)
timer B07 AF2
# pin B07: TIM4 CH2 (AF2)
timer C09 AF3
# pin C09: TIM8 CH4 (AF3)
timer C08 AF3
# pin C08: TIM8 CH3 (AF3)
timer A09 AF1
# pin A09: TIM1 CH2 (AF1)

# dma
dma ADC 1 0
# ADC 1: DMA2 Stream 0 Channel 0
dma pin B00 0
# pin B00: DMA1 Stream 7 Channel 5
dma pin B01 0
# pin B01: DMA1 Stream 2 Channel 5
dma pin A03 1
# pin A03: DMA1 Stream 6 Channel 3
dma pin A02 0
# pin A02: DMA1 Stream 1 Channel 3
dma pin B05 0
# pin B05: DMA1 Stream 5 Channel 5
dma pin B07 0
# pin B07: DMA1 Stream 3 Channel 2
dma pin C09 0
# pin C09: DMA2 Stream 7 Channel 7
dma pin C08 0
# pin C08: DMA2 Stream 2 Channel 0
dma pin A09 0
# pin A09: DMA2 Stream 6 Channel 0

# feature
feature LED_STRIP
feature OSD

# serial
serial 0 64 115200 57600 0 115200
serial 5 131073 115200 57600 0 115200

# led
led 0 7,6::CO:11
led 1 8,6::CO:11

# aux
aux 0 0 0 1300 2100 0 0
aux 1 1 1 1400 1625 0 0
aux 2 27 3 1300 2100 0 0
aux 3 13 5 1300 2100 0 0
aux 4 26 7 1275 1550 0 0
aux 5 31 7 1050 1150 0 0
aux 6 35 1 1700 2100 0 0
aux 7 36 2 1300 2100 0 0
aux 8 40 6 900 1475 0 0
aux 9 52 5 900 1700 0 0

# adjrange
adjrange 0 0 4 900 2100 12 4 0 0

# master
set dyn_notch_min_hz = 60
set dyn_notch_max_hz = 300
set acc_calibration = -20,13,-16,1
set mag_hardware = NONE
set baro_bustype = I2C
set baro_i2c_device = 1
set serialrx_provider = CRSF
set blackbox_device = SPIFLASH
set dshot_idle_value = 800
set dshot_bidir = ON
set dshot_bitbang = OFF
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set motor_output_reordering = 1,0,3,2,4,5,6,7
set current_meter = ADC
set battery_meter = ADC
set vbat_scale = 111
set ibata_scale = 170
set beeper_inversion = ON
set beeper_od = OFF
set yaw_motors_reversed = ON
set small_angle = 180
set pid_process_denom = 4
set osd_units = IMPERIAL
set osd_warn_bitmask = 18431
set osd_vbat_pos = 418
set osd_link_quality_pos = 3497
set osd_tim_1_pos = 471
set osd_tim_2_pos = 2519
set osd_remaining_time_estimate_pos = 2552
set osd_flymode_pos = 2210
set osd_throttle_pos = 2146
set osd_crosshairs_pos = 2361
set osd_ah_sbar_pos = 2362
set osd_ah_pos = 2234
set osd_current_pos = 2529
set osd_mah_drawn_pos = 289
set osd_motor_diag_pos = 2178
set osd_craft_name_pos = 2071
set osd_warnings_pos = 14613
set osd_avg_cell_voltage_pos = 2498
set osd_battery_usage_pos = 2580
set osd_disarmed_pos = 2422
set osd_flip_arrow_pos = 2087
set osd_core_temp_pos = 3176
set osd_rate_profile_name_pos = 2242
set osd_sys_delay_pos = 3560
set osd_sys_distance_pos = 2082
set osd_sys_lq_pos = 3528
set osd_sys_goggle_dvr_pos = 3591
set osd_sys_warnings_pos = 2260
set osd_sys_vtx_temp_pos = 3144
set osd_sys_fan_speed_pos = 1227
set osd_displayport_device = MSP
set system_hse_mhz = 8
set vcd_video_system = HD
set max7456_spi_bus = 3
set pinio_box = 40,41,255,255
set flash_spi_bus = 3
set gyro_1_bustype = SPI
set gyro_1_spibus = 1
set gyro_1_sensor_align = CW180
set gyro_1_align_yaw = 1800
set gyro_2_spibus = 1
set craft_name = Voyager 1
set pilot_name = (406) 589-9423

profile 0

# profile 0
set dterm_lpf1_static_hz = 0
set iterm_relax_cutoff = 25
set p_pitch = 64
set i_pitch = 127
set d_pitch = 77
set f_pitch = 148
set p_roll = 61
set i_roll = 121
set d_roll = 67
set f_roll = 142
set p_yaw = 61
set i_yaw = 121
set f_yaw = 142
set d_min_roll = 65
set d_min_pitch = 74
set thrust_linear = 20
set feedforward_averaging = 2_POINT
set feedforward_smooth_factor = 60
set feedforward_jitter_factor = 10
set simplified_master_multiplier = 125
set simplified_i_gain = 110
set simplified_d_gain = 175
set simplified_pi_gain = 110
set simplified_dmax_gain = 10
set simplified_feedforward_gain = 95

rateprofile 0

# rateprofile 0
set rateprofile_name = CINWOOP1
set rates_type = BETAFLIGHT
set roll_rc_rate = 125
set pitch_rc_rate = 125
set yaw_rc_rate = 201
set pitch_expo = 31
set yaw_expo = 37
set roll_srate = 29
set pitch_srate = 29
set yaw_srate = 0
set throttle_limit_type = SCALE
set throttle_limit_percent = 80

# end the command batch
batch end

Add any other context about the problem that you think might be relevant here

No response

[haslinghuis]

Post support id generated using button in cli.