Setting stage 2 config

[JayGDee]

Hi
I have an issue with the program not advancing past Setting stage 2 config.
I left it to run all night, thinking it may just take a while, but in the morning, it was still stuck there.
This is on a generic tablet Media Tek MT6592.
Here's the readout from the debug.
[17:40:59]: Status: Waiting for PreLoader VCOM, please connect mobile
[17:41:13]: CPU: MT6592()
[17:41:13]: HW version: 0x0
[17:41:13]: WDT: 0x10007000
[17:41:13]: Uart: 0x11002000
[17:41:13]: Brom payload addr: 0x100a00
[17:41:13]: DA payload addr: 0x111000
[17:41:13]: CQ_DMA addr: 0x10212000
[17:41:13]: Var1: 0xa
[17:41:13]: Disabling Watchdog...
[17:41:13]: HW code: 0x6592
[17:41:13]: Target config: 0x0
[17:41:13]: SBC enabled: False
[17:41:13]: SLA enabled: False
[17:41:13]: DAA enabled: False
[17:41:13]: SWJTAG enabled: False
[17:41:13]: EPP_PARAM at 0x600 after EMMC_BOOT/SDMMC_BOOT: False
[17:41:13]: Root cert required: False
[17:41:13]: Mem read auth: False
[17:41:13]: Mem write auth: False
[17:41:13]: Cmd 0xC8 blocked: False
[17:41:13]: Get Target info
[17:41:13]: BROM mode detected.
[17:41:13]: HW subcode: 0x8a00
[17:41:13]: HW Ver: 0xca00
[17:41:13]: SW Ver: 0x0
[17:41:13]: ME_ID: 5E3CFD31C57C96DF2A37399B8BCC7968
[17:41:15]: Device is unprotected.
[17:41:15]: Device is in BROM-Mode. Bypassing security.
[17:41:15]: Loading payload from mt6592_payload.bin, 0x258 bytes
[17:41:15]: Kamakiri / DA Run
[17:41:15]: Trying kamakiri2..
[17:41:15]: Done sending payload...
[17:41:16]: Successfully sent payload: C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\payloads\mt6592_payload.bin
[17:41:16]: Device is in BROM mode. No preloader given, trying to dump preloader from ram.
[17:41:17]: Uploading legacy da...
[17:41:17]: Uploading legacy stage 1 from MTK_AllInOne_DA_5.1420.bin
[17:41:17]: Jumping to 0x110000
[17:41:17]: Jumping to 0x110000: ok.
[17:41:17]: Got loader sync !
[17:41:17]: Reading nand info
[17:41:17]: NAND_INFO: 0xbc0
[17:41:17]: Reading emmc info
[17:41:17]: EMMC_INFO: 0x0
[17:41:17]: ACK: 04028a
[17:41:17]: Setting stage 2 config ...

Any ideas?

Also, when I stop the GUI, this is the readout I get from Powershell
Port - Device detected :)
legacyext
legacyext - [LIB]: ←[33mLegacy address check not patched.←[0m
None
Traceback (most recent call last):
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\gui\toolkit.py", line 113, in run
self.function(self, self.parameters)
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtk_gui", line 87, in getDevInfo
mtkClass = da_handler.configure_da(mtkClass, preloader=None)
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\Library\mtk_da_cmd.py", line 112, in configure_da
if not mtk.daloader.upload_da(preloader=preloader):
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\Library\mtk_daloader.py", line 202, in upload_da
return self.da.upload_da()
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\Library\mtk_dalegacy.py", line 1067, in upload_da
if self.upload():
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\Library\mtk_dalegacy.py", line 1039, in upload
self.set_stage2_config(self.config.hwcode)
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\Library\mtk_dalegacy.py", line 831, in set_stage2_config
self.config.bmtsettings(self.config.hwcode)
File "C:\Users\hanum\Desktop\MTK Tools\mtkclient-main\mtkclient\config\mtk_config.py", line 192, in bmtsettings
if self.da.daconfig.flashtype == "emmc":
AttributeError: 'NoneType' object has no attribute 'daconfig'