[BUG] X2 and X3 stops extruding on first layer on Jan build both are N32 boards #197
Comments
|
im somewhat new to all this, but with "Alex's" firmare on my X2 i have 4000 hours of prints all worked just fine. i tried to upgrade to to the Jan 2025 firmware and it all went wrong. i dont know how to edit or compile firmware myself, so your help would be great. the X2 has the added CR touch, while the X3 is all stock out of the box (inductive sensor) |
|
I suggest try using PROUI_EX version. otherwise, an older release should work like If it is the non-ProUI-EX that is the issue that will help narrow it down and I'll look into it. |
|
Hi, thanks for responding. I failed to mention the machine is an X3 Plus. 300x300x300. I did flash with the Oct. PROUI_EX version and the same happened. Prints the perimeter fine, when it goes to fill in, it stops extruding but keeps going as if it was.
Sent from AOL on Android
On Sat, Feb 8, 2025 at 6:28 PM, ***@***.***> wrote:
I suggest try using PROUI_EX version. otherwise, an older release should work like 2.1.3f-10 (October).
If it is the non-ProUI-EX that is the issue that will help narrow it down and I'll look into it.
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
|
having it stop extruding after first layer is an odd issue. is there anything in your Gcode file that has search into your Gcode print file for if you like attach/send the Gcode file you are using and I can take a quick look. edit: also, for the Plus version that must use the ProUI_EX because you need to change the physical size of the printer through Advanced Settings |
|
hi, yes i did use the ProUI_EX (Oct 2024, build) and changed the bed size to X=300 and Y=300. Also set the max X an Y travel to 300 did not make a difference when i set it to do bed mesh leveling. only scanned 230x230. i flashed back to the stock firmware and printed the same file 4 times fine. the g-code(pasted below) unless theres new code in Marlin, it does not load the mesh leveling data for the bed. trying to remember think its M420 /S or something like that. i will have to add the correct code into Voxelmaker slicer. i really appreciate all your help!!!! if you need the whole file let me know. ;generated by ffslicer 1.30.3 02/08/25 01:11:49 |
|
you did mention you tried the recent latest release? because someone else who uses 400x400x400 Aquila Max says they have no issue now. ill take a look at your code and even try printing and see if I get the same issue. |
|
hey, i flashed it to tonite... Aquila_N32_IND_UBL-ProUI-EX-01-30.bin if that is not the correct one, please link it for me. i did take the same G-code file and put it in my X2 and it prints fine. on the X3 plus it still prints the perimeter and then stops on the infill, and at the same time i noticed the "hot end" heater shuts off. but the bed stays heating. |
|
ive tried a few versions, so i could not remember. none worked though, i did just notice the heater shutting off when it goes to infill tonite. |
|
that file should be correct one with Induction Probe. |
|
The X2 is back on the old Alex firmware. I tried last night flashing the X3 and it did the same as before. I just noticed that when it's printing the perimeter and switches to do the infill on the first layer, it stops extruding and shuts the hot end heater off, but keeps trying to print. If I then shut it off and flash it back to stock, and set it to print the same file, it prints fine. I was just testing to make sure it wasn't something with the slicer. I'm gunna take the cover off the motherboard and get a couple photos of it. The X3 plus is brand new. Wondering if they changed something on it.
Sent from AOL on Android
On Fri, Feb 14, 2025 at 11:07 AM, ***@***.***> wrote:
that file should be correct one with Induction Probe.
so everything is working fine on the X2 now, but still issue with X3? could it be possible there is something with the wiring connection?
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you authored the thread.Message ID: ***@***.***>
classicrocker883 left a comment (classicrocker883/MRiscoCProUI#197)
that file should be correct one with Induction Probe.
so everything is working fine on the X2 now, but still issue with X3? could it be possible there is something with the wiring connection?
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Did you test the latest release build?
Yes, and the problem still exists.
Bug Description
hi, the speed seems ok, but it stops extruding on the first layer and keeps going. the extruder motor stops completely, but continues to try and print. help
Printer Model
Voxelab Aquila
Model Type
X2 X3
Your Mainboard
Aquila N32
Other Mainboard Type
No response
Add-ons that could be involved
CR touch for the X2, Inductive for X3
ProUI-EX | Extra Features?
No (formerly NoPro)
Bed Leveling
UBL - Unified Bed Leveling
Did you include your own configuration files?
Configuration.handConfiguration_adv.h.Additional information & file uploads
No response
The text was updated successfully, but these errors were encountered: