Skip to content

Latest commit

 

History

History
137 lines (114 loc) · 3.9 KB

cni.md

File metadata and controls

137 lines (114 loc) · 3.9 KB
Raw

Using CNI with nerdctl

nerdctl uses CNI plugins for its container network, you can set network by either --network or --net option.

Basic networks

nerdctl support some basic types of CNI plugins without any configuration needed(you should have CNI plugin be installed), for Linux systems the basic CNI plugin types are bridge, portmap, firewall, tuning, for Windows system, the supported CNI plugin types are nat only.

The default network bridge for Linux and nat for Windows if you don't set any network options.

Configuration of the default network bridge of Linux:

{
  "cniVersion": "1.0.0",
  "name": "bridge",
  "plugins": [
    {
      "type": "bridge",
      "bridge": "nerdctl0",
      "isGateway": true,
      "ipMasq": true,
      "hairpinMode": true,
      "ipam": {
        "type": "host-local",
        "routes": [{ "dst": "0.0.0.0/0" }],
        "ranges": [
          [
            {
              "subnet": "10.4.0.1",
              "gateway": "10.4.0.0/24"
            }
          ]
        ]
      }
    },
    {
      "type": "portmap",
      "capabilities": {
        "portMappings": true
      }
    },
    {
      "type": "firewall",
      "ingressPolicy": "same-bridge"
    },
    {
      "type": "tuning"
    }
  ]
}

Bridge isolation

nerdctl >= 0.18 sets the ingressPolicy to same-bridge when firewall plugin >= 1.1.0 is installed. This ingressPolicy replaces the CNI isolation plugin used in nerdctl <= 0.17.

When the isolation plugin is found, nerdctl uses the isolation plugin instead of ingressPolicy. The isolation plugin has been deprecated, and a future version of nerdctl will solely support ingressPolicy.

When neither of firewall plugin >= 1.1.0 or isolation plugin is found, nerdctl does not enable the bridge isolation. This means a container in --net=foo can connect to a container in --net=bar.

macvlan/IPvlan networks

nerdctl also support macvlan and IPvlan network driver.

To create a macvlan network which bridges with a given physical network interface, use --driver macvlan with nerdctl network create command.

# nerdctl network create mac0 --driver macvlan \
  --subnet=192.168.5.0/24
  --gateway=192.168.5.2
  -o parent=eth0

You can specify the parent, which is the interface the traffic will physically go through on the host, defaults to default route interface.

And the subnet should be under the same network as the network interface, an easier way is to use DHCP to assign the IP:

# nerdctl network create mac0 --driver macvlan --ipam-driver=dhcp

Using --driver ipvlan can create ipvlan network, the default mode for IPvlan is l2.

Custom networks

You can also customize your CNI network by providing configuration files. For example you have one configuration file(/etc/cni/net.d/10-mynet.conf) for bridge network:

{
  "cniVersion": "1.0.0",
  "name": "mynet",
  "type": "bridge",
  "bridge": "cni0",
  "isGateway": true,
  "ipMasq": true,
  "ipam": {
    "type": "host-local",
    "subnet": "172.19.0.0/24",
    "routes": [
      { "dst": "0.0.0.0/0" }
    ]
  }
}

This will configure a new CNI network with the name mynet, and you can use this network to create a container:

# nerdctl run -it --net mynet --rm alpine ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
3: eth0@if6120: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue state UP
    link/ether 5e:5b:3f:0c:36:56 brd ff:ff:ff:ff:ff:ff
    inet 172.19.0.51/24 brd 172.19.0.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::5c5b:3fff:fe0c:3656/64 scope link tentative
       valid_lft forever preferred_lft forever