Getting No PSRAM found on first boot

[Drizzt321]

So I got this esp32-cam, and when using your sketch I get No PSRAM found; camera cannot be initialised: Please check the board config for your module. as an error on first boot. Screenshot and full output is below.

I did ensure in Tools->PSRAM -> Enabled is set, using latest Arduino (2.0.3) and esp32 boards (2.0.6) is installed.

configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13836
load:0x40080400,len:3608
entry 0x400805f0
E (242) psram: PSRAM ID read error: 0xffffffff

====

esp32-cam-webserver: ESP32 camera server
Code Built: Feb  3 2023 @ 11:15:57
Base Release: 4.0


Fatal Error; Halting
No PSRAM found; camera cannot be initialised: Please check the board config for your module.

[sonofcy]

You have the wrong board selected, it has to be AI Thinker ESP32-CAM

[Drizzt321]

Instructions in the README says to use the generic ESP32 Dev Module

[sonofcy]

THINK, does that have a camera? I have dozens of these and work with them all the time. The README is wrong.

[Drizzt321]

Set the board to AI Thinker ESP32-CAM, same issue, No PSRAM found.

Note, this is NOT an AI-Thinker branded board, see Amazon link I have above, is what I'm trying to use. Wonder if this particular module, ESP32-S, just doesn't have any PSRAM.

[sonofcy]

The board I am using is also NOT an AI-THINKER, it is similar to what you have. I do NOT fool around with the settings on the IDE board menu. I just compiled and it works.

[sonofcy]

12:45:49.781 -> 0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 (POWERON_RESET),boot:0x13 (S0x1 AST_FLASH_BOOT)
12:45:49.781 -> configsip: 0, SPIWP:0xee
12:45:49.781 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
12:45:49.781 -> mode:DIO, clock div:1
12:45:49.781 -> load:0x3fff0030,len:1344
12:45:49.781 -> load:0x40078000,len:13836
12:45:49.781 -> load:0x40080400,len:3608
12:45:49.781 -> entry 0x400805f0
12:45:50.731 ->
12:45:51.617 -> ...
12:45:52.601 -> WiFi connected
12:45:52.601 -> Camera Ready! Use 'http://192.168.0.122' to connect

[Drizzt321]

What were your compile settings? I didn't "mess around", I followed the README on the project. If that's wrong, then please tell me what the correct settings are.

[sonofcy]

Ialmost never read README's, they get out of date the first change. My IDE is set up the same for any board, either ALL or DEFAULT compiler warnings, then all the usual stuff, I have NEVER changed any setting in the boards, I don't even see the PSRAM setting you changed. The sample sketch is set up for AI-THINKER, I specify the AI-THINKER board and it just works, I just tried it.

[Ropese]

Good morning
I also have the psram problem I tried 3 esp32-s only one goes the others psram error I changed the camera modules but still the same.
how can it be that 1 goes and the others don't?
i tried with other skretch and other modules work too but not with this any idea?
Thank you

[Emstar]

EDIT: While the procedure below does work, as I feared it did cause problems when compiling projects for other boards. I found that as @sonofcy said, you must select the AI Thinker board type in the IDE, and NOT the ESP32 Dev Module as the docs say. With AI Thinker selected the PSRAM is detected without workarounds.

---

I have the same kind of ESP32-S board and had the same PSRAM problem when using board type ESP32 Dev Module.

I found the solution in this post: https://www.esp32.com/viewtopic.php?t=31247#p107434

In C:\Users\USERNAME\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.13\cores\esp32\esp32-hal-psram.c rig the PSRAM test:

//#if CONFIG_SPIRAM_SUPPORT || CONFIG_SPIRAM
#if 1

In esp32-cam-webserver.ino, in setup(), add this after the block of startup serial.print() statements near line 650.

    if (psramInit()) {
      Serial.print("PSRAM OK. Size: ");
      Serial.println(ESP.getFreePsram());
      }

In myconfig.h continue to use the default AI_THINKER definition.

While this worked there is probably a better way to do it. This is my first project, I don't know this environment or hardware at all. Modifying a core library file sucks and seems like it would break compatibility with other boards.

I also noticed that PSRAM did not seem to initialize properly on every bootup. Sometimes you have to push the reset button to get the board to come up.

If anyone can suggest the right way to implement this support without messing with esp32-hal-psram.c I would love to know.