Skip to content

Latest commit

 

History

History
117 lines (88 loc) · 4.04 KB

nrf52-hardware.md

File metadata and controls

117 lines (88 loc) · 4.04 KB
Raw

nRF52 Hardware

nRF52840 Dongle

Connect the Dongle to your PC/laptop. Its red LED should start oscillating in intensity. The device will also show up as:

Windows: a USB Serial Device (COM port) in the Device Manager under the Ports section

Linux: a USB device under lsusb. The device will have a VID of 0x1915 and a PID of 0x521f -- the 0x prefix will be omitted in the output of lsusb:

$ lsusb
(..)
Bus 001 Device 023: ID 1915:521f Nordic Semiconductor ASA 4-Port USB 2.0 Hub

The device will also show up in the /dev directory as a ttyACM device:

$ ls /dev/ttyACM*
/dev/ttyACM0

macOS: a usb device when executing ioreg -p IOUSB -b -n "Open DFU Bootloader". The device will have a vendor ID ("idVendor") of 6421 and a product ID ("idProduct") of 21023:

$ ioreg -p IOUSB -b -n "Open DFU Bootloader"
(...)
| +-o Open DFU Bootloader@14300000  <class AppleUSBDevice, id 0x100005d5b, registered, matched, ac$
  |     {
  |       (...)
  |       "idProduct" = 21023
  |       (...)
  |       "USB Product Name" = "Open DFU Bootloader"
  |       (...)
  |       "USB Vendor Name" = "Nordic Semiconductor"
  |       "idVendor" = 6421
  |       (...)
  |       USB Serial Number" = "CA1781C8A1EE"
  |       (...)
  |     }
  |

The device will show up in the /dev directory as tty.usbmodem<USB Serial Number>:

$ ls /dev/tty.usbmodem*
/dev/tty.usbmodemCA1781C8A1EE1

nRF52840 Development Kit (DK)

Connect one end of a micro USB cable to the USB connector J2 of the board and the other end to your PC.

💬 These directions assume you are holding the board "horizontally" with components (switches, buttons and pins) facing up. In this position, rotate the board, so that its convex shaped short side faces right. You'll find one USB connector (J2) on the left edge, another USB connector (J3) on the bottom edge and 4 buttons on the bottom right corner.

Labeled Diagram of the nRF52840 Development Kit (DK)

After connecting the DK to your PC/laptop it will show up as:

Windows: a removable USB flash drive (named JLINK) and also as a USB Serial Device (COM port) in the Device Manager under the Ports section

Linux: a USB device under lsusb. The device will have a VID of 0x1366 and a PID of 0x10?? or 0x01?? (? is a hex digit) -- the 0x prefix will be omitted in the output of lsusb:

$ lsusb
(..)
Bus 001 Device 014: ID 1366:1051 SEGGER 4-Port USB 2.0 Hub

The device will also show up in the /dev directory as a ttyACM device:

$ ls /dev/ttyACM*
/dev/ttyACM0

macOS: a removable USB flash drive (named JLINK) in Finder and also a USB device named "J-Link" when executing ioreg -p IOUSB -b -n "J-Link".

$ ioreg -p IOUSB -b -n "J-Link"
(...)
  | +-o J-Link@14300000  <class AppleUSBDevice, id 0x10000606a, registered, matched, active, busy 0 $
  |     {
  |       (...)
  |       "idProduct" = 4117
  |       (...)
  |       "USB Product Name" = "J-Link"
  |       (...)
  |       "USB Vendor Name" = "SEGGER"
  |       "idVendor" = 4966
  |       (...)
  |       "USB Serial Number" = "000683420803"
  |       (...)
  |     }
  |

The device will also show up in the /dev directory as tty.usbmodem<USB Serial Number>:

$ ls /dev/tty.usbmodem*
/dev/tty.usbmodem0006834208031

The board has several switches to configure its behavior. The out of the box configuration is the one we want. If the above instructions didn't work for you, check the position of the following switches:

  • SW6 is set to the DEFAULT position (to the right - nRF = DEFAULT).
  • SW7 (protected by Kapton tape) is set to the Def. position (to the right - TRACE = Def.).
  • SW8 is set to the ON (to the left) position (Power = ON)
  • SW9 is set to the VDD position (center - nRF power source = VDD)
  • SW10 (protected by Kapton tape) is set to the OFF position (to the left - VEXT -> nRF = OFF).

For reference, here's the board picture again:

Labeled Diagram of the nRF52840 Development Kit (DK)