forked from 1technophile/OpenMQTTGateway
-
Notifications
You must be signed in to change notification settings - Fork 2
/
config_IR.h
105 lines (93 loc) · 3.59 KB
/
config_IR.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
/*
OpenMQTTGateway - ESP8266 or Arduino program for home automation
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
Send and receiving command by MQTT
This files enables to set your parameter for the infrared gateway
Copyright: (c)Florian ROBERT
This file is part of OpenMQTTGateway.
OpenMQTTGateway is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
OpenMQTTGateway is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*-------------------IR topics & parameters----------------------*/
//IR MQTT Subjects
#define subjectGTWIRtoMQTT Base_Topic Gateway_Name "/IRtoMQTT"
#define subjectIRtoMQTT Base_Topic Gateway_Name "/IRtoMQTT"
#define subjectMQTTtoIR Base_Topic Gateway_Name "/commands/MQTTtoIR"
// subject monitored to listen traffic processed by other gateways to store data and avoid ntuple
#define subjectMultiGTWIR "+/+/IRtoMQTT"
#define IRbitsKey "IRBITS_" // bits will be defined if a subject contains IRbitsKey followed by a value of 2 digits
#define IRRptKey "RPT_" // repeats will be defined if a subject contains IRRptKey followed by a value of 1 digit
#define repeatIRwMQTT false // do we repeat a received signal by using mqtt
#define repeatIRwNumber 3 // default repeat of the signal
#define RawDirectForward false // direct repeat of IR signal with raw data
#define RawFrequency 38 // raw frequency sending
//#define DumpMode true // uncomment so as to see big dumps of IR codes
#define pubIRunknownPrtcl false // key to avoid mqtt publication of unknown IR protocol (set to true if you want to publish unknown protocol)
#define PanasonicAddress 0x4004 // Panasonic address (Pre data)
#ifdef ESP8266 //IR supported protocols on ESP8266, all supported per default
#define IR_GC
#define IR_Raw
#define IR_COOLIX
#define IR_Whynter
#define IR_LG
#define IR_Sony
#define IR_DISH
#define IR_RC5
#define IR_RC6
#define IR_Sharp
#define IR_SAMSUNG
#define IR_PANASONIC
#define IR_RCMM
#define IR_MITSUBISHI
#define IR_GICABLE
#define IR_MITSUBISHI2
#define IR_LASERTAG
#define IR_CARRIER_AC
#define IR_MIDEA
#define IR_NIKAI
#define IR_SHERWOOD
#define IR_DENON
#define IR_AIWA_RC_T501
#define IR_JVC
#elif ESP32
#define IR_Raw
#define IR_COOLIX
#define IR_Whynter
#define IR_Sony
#define IR_LG
#define IR_DISH
#define IR_RC5
#define IR_Sharp
#define IR_SAMSUNG
#define IR_PANASONIC
#else //IR supported protocols on arduino uncomment if you want to send with this protocol, NEC protocol is available per default
//#define IR_COOLIX
//#define IR_Whynter
//#define IR_LG
//#define IR_Sony
//#define IR_DISH
//#define IR_RC5
//#define IR_Sharp
//#define IR_SAMSUNG
//#define IR_Raw
//#define IR_PANASONIC
#endif
/*-------------------PIN DEFINITIONS----------------------*/
#ifdef ESP8266
#define IR_RECEIVER_PIN 2
#define IR_EMITTER_PIN 16 // replace by 0 if you use IR LOLIN controller shield
#elif ESP32
#define IR_RECEIVER_PIN 27
#define IR_EMITTER_PIN 14
#else
#define IR_RECEIVER_PIN 0 // 0 = D2 on arduino
#define IR_EMITTER_PIN 9
#endif