forked from cookem4/T265ControlSystem
-
Notifications
You must be signed in to change notification settings - Fork 0
/
flightcontrolling.py
executable file
·101 lines (82 loc) · 3.68 KB
/
flightcontrolling.py
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
###########################################
##########Used for controlling#############
#######cleanflight fligh controller########
###########################################
from Cleanflight_MSP import Cleanflight_MSP
import serial
import os
import time
cleanflightMSP0 = Cleanflight_MSP('/dev/ttyUSB0', 115200)
######################################
#######SUMMARY OF ISSUES##############
######################################
#Data can be sent over UART TX port of pi as if it is connected to an LED the LED blinks
#PC connot receive this data when a USB to TTL converter is used
#The LED on the USB to TTL converter flahses but no data is recieved in RealTerm on the PC
#The COM port of the USB to TTL convert shows
#The current UART port is set to be on ttyAMA0
#Transmitting data with MSP in the same way the motion capture program does results in no activity on the flight controller
#Both the pi and the RF receiver have a single wire going from a 3.3V port on the board to the RX pin on the CleanFlight UART
#The pi gets no response even though the connection is exactly the same
#Using the pi with the pyMultiWii program it is also not able to establish connection with the flight contorller
#*****************The use of USB0 by connectiong with microUSB can be promising***********
#Works with micro usb connection to the flight controller!!!!!!!!!!!!!
ARM = 1600; DISARM = 1000; ANGLE_MODE = 1600; NEUTRAL = 1000;
ZERO_ROLL = 1500; ZERO_PITCH = 1500; ZERO_YAW_RATE = 1500; ZERO_THROTTLE = 1000;
zeroCommands = [ZERO_ROLL, ZERO_PITCH, ZERO_THROTTLE, ZERO_YAW_RATE, ARM, ANGLE_MODE, NEUTRAL, NEUTRAL]
commandsToGo = []
HZ=100
disArmCommandsToGoMSP = [ZERO_ROLL, ZERO_PITCH, ZERO_THROTTLE, ZERO_YAW_RATE, DISARM, ANGLE_MODE, NEUTRAL, NEUTRAL] # The 1600 is to enable the "Angle Mode" in clean flight.
armCommandsToGoMSP = [ZERO_ROLL, ZERO_PITCH, ZERO_THROTTLE, ZERO_YAW_RATE, ARM, ANGLE_MODE, NEUTRAL, NEUTRAL]
dataLength = len(disArmCommandsToGoMSP)
dataBytes = 2*dataLength
direction = '<'
commandsToGo = [ZERO_ROLL, ZERO_PITCH, ZERO_THROTTLE, ZERO_YAW_RATE, ARM, ANGLE_MODE, NEUTRAL, NEUTRAL]
h = 'h'
print("Disarming...")
for i in range(1, 20): #command for about a second before arming
cleanflightMSP0.sendMSP(direction, dataBytes, 200, disArmCommandsToGoMSP, direction+ str(dataLength) + h)
time.sleep(1/HZ)
print("Arming...")
for i in range(1, 20):
cleanflightMSP0.sendMSP(direction, dataBytes, 200, armCommandsToGoMSP, direction+ str(dataLength) + h)
time.sleep(1/HZ)
print("Active...")
#Send throttle data to the copters
i=0
try:
while (i<200):
commandsToGo[2] = commandsToGo[2] + 1
cleanflightMSP0.sendMSP(direction, dataBytes, 200, commandsToGo, direction+ str(dataLength) + h)
time.sleep(1/HZ)
i=i+1
print("Iteration #" + str(i))
i=0
while(i<200):
commandsToGo[2] = commandsToGo[2] - 1
cleanflightMSP0.sendMSP(direction, dataBytes, 200, commandsToGo, direction+ str(dataLength) + h)
time.sleep(1/HZ)
i=i+1
print("Iteration #" + str(i))
except KeyboardInterrupt:
print("Program Force Stopped")
#Try looking at this video:
#https://www.youtube.com/watch?v=GJuWpBCgQPQ
#ser = serial.Serial('/dev/ttyAMA0',
# baudrate=9600,
# parity=serial.PARITY_NONE,
# stopbits=serial.STOPBITS_ONE,
# bytesize=serial.EIGHTBITS,
# timeout=3.0
# )
#try:
# print("Writing to serial...")
# while(1):
# ser.write("Testing".encode("utf8"))
#except KeyboardInterrupt:
# print("Exiting program")
#except Exception as e:
# print(e)
#finally:
# ser.close()
# pass