Web Builder issues 2025

[terjeio]

For reporting issues with the Web Builder. Previous discussion can be found here.

[joyfab]

grblHAL build/patch 20250114.
Driver: RP2040 (Pi Pico & Pi Pico W)
Board : BTT SKR Pico 1.0
Native USB or virtual 3 axes: No Work. Alarm $X error 79. No way to unlock.
Native USB or virtual 4 axes: run like a charm with 4 axes. $X unlock is available.
So using 4 instead 3 but don't now why..
release 20240228 was running well in 3 axis but new version give a problem on 3 axis:
no way to unlock, as well as on Pico or PicoW.

[terjeio]

Native USB or virtual 3 axes: No Work. Alarm $X error 79. No way to unlock.

$14 cannot be used to invert the estop input?

[terjeio]

Should be fixed now.

[Dexus]

grblHAL/RP2040#109

mdns not build

[TPMoyer]

Terje:
Yes I understand this is off topic, but am unaware of another way to contact you.
I made a mistake and deleted the "Additional or extended settings" page from the core/wiki
Please restore the page.

Had opened an edit to point to a new page enumerating the outputs from $help and the several $help topic   commands.     

Got stuck in the edit, and bailed by pushing the delete page button.
This deleted the original page, not just the incorrectly modified page.
Ohhhhh crap.

[terjeio]

Restored now.

[Perlovka]

Building for Teensy fails with error 422

Command failed: pio run -etest -cjob.ini
src/ioports_analog.c: In function 'wait_on_input':
src/ioports_analog.c:387:16: error: 'mcp3221' undeclared (first use in this function)
if(port == mcp3221.id)
^
src/ioports_analog.c:387:16: note: each undeclared identifier is reported only once for each function it appears in
src/ioports_analog.c: In function 'get_pin_info':
src/ioports_analog.c:412:34: error: 'mcp3221' undeclared (first use in this function)
if(pin.id == mcp3221.id)
^
src/ioports_analog.c: In function 'set_pin_description':
src/ioports_analog.c:446:24: error: 'mcp3221' undeclared (first use in this function)
if(port == mcp3221.id)
^
src/ioports_analog.c: In function 'claim':
src/ioports_analog.c:468:30: error: 'mcp3221' undeclared (first use in this function)
*port == mcp3221.id ? mcp3221.mode.claimed :
^
*** [.pio/build/test/src/ioports_analog.c.o] Error 1
========================= [FAILED] Took 16.66 seconds =========================

[terjeio]

Fixed, thanks for reporting.

[dddidi]

Was trying to build a new firmware with the web builder because I am strugling with #653 and #634 too when building with pio under windows.
But currently the build process for ESP32 boards is not working.
I have tried several times with different settings and different boards for ESP, but I always get the error: message Build failed: 504

[terjeio]

Try again now, I have been meddling with the Web Builder code (I do not have a test server yet).
If still fails the which board are you compiling for?

[dddidi]

Thank you for your quick response.
I am trying to build for the "MKS Tinybee V1.0"
For the test I did not set any parameters just selected the board and pressed generate.
But the build failed again (Build failed: 504)

[terjeio]

Builds for me. Did you reload the page (I forgot to mention that).

[dddidi]

OK. Reload of the Page did the trick.
Thank you very much for your help.
I was able to download the firmware.

[euridium]

i am trying to build for picobob_dlx. 4 axis with networking.
the reset pin is not mapped as you would expexct (gpio 3), as its state isn't changed by the estop input on a mach3 BOB.
when i compile the picobob non delux - the pin is proppery mapped and it works.

looking at the board profiles i suspect it is to do with this section :

// Define user-control controls (cycle start, reset, feed hold) input pins. Only Estop is supported on the Mach3 BOB.
#ifndef I2C_STROBE_ENABLE
#define RESET_PIN 3
#else
//reset pin is swapped to keypad when present, frees up additional input.
#define RESET_PIN 15
#define AUXINPUT2_PIN 3
#endif

so is i2c strobe set, when it should not be (i havn't selected the MPG and keyboard etc.)

thoughts?