Skip to content

Latest commit

 

History

History
1021 lines (863 loc) · 51.2 KB

CHANGELOG.md

File metadata and controls

1021 lines (863 loc) · 51.2 KB

ESPurna change log

The format is based on Keep a Changelog and this project adheres to Semantic Versioning.

[1.13.0] 2018-06-22

Fixed

  • Fixed PZEM004T compilation issues, working when using hardware serial (#837)
  • Fixed per channel state on/off for lights (#830)
  • Fixed overflow in CSE7766 energy calculation (#856)
  • Fixed On MQTT disconnect in web UI (#845)
  • Check valid hostnames (#874, #879)
  • Fix Sonoff POW R2 configuration
  • Fixed InfluxDB sensor by id (#882)
  • Fix build when disabling WEB_SUPPORT (#923)
  • Fix calibration error in EmonSensor (#876)
  • Fix telnet and web debug responsiveness (#896)
  • Use double quotes in JSON for non-numeric values (#929)
  • Support connections over HTTPS via proxy (#937)

Added

  • EEPROM sector rotation using EEPROM_Rotate library
  • Code filtering when building web UI images
  • Added pulsing a relay via MQTT and REST API (#896, #902)
  • Support for WPS (not available in pre-built binaries)
  • Support for Smart Config (not available in pre-built binaries)
  • Support for CCT lights (thanks to @Skaronator)
  • Allow RELAYx_DELAY_ON/OFF also for none GPIO relay types (thanks to @zafrirron)
  • Added relay status to Domoticz on MQTT connection (#872)
  • Added configurable UART-to-MQTT terminator
  • Added telnet link to web UI
  • Reload terminal command to force all modules to reload settings from config (#816)
  • Added security headers to each HTTP response (thanks to @ITNerdBox)
  • Customized GET terminal command (thanks to @mcspr)
  • More RC codes supported on TX for RF Bridge (thanks to @wildwiz)
  • Support for BL0937 power monitoring chip with unmodified HLW8012 library (#737)
  • Enable CORS
  • Support for Allnet ESP8266 UP Relay (thanks to @bajo)
  • Support for Tonbux Mosquito Killer (thanks to @gn0st1c)
  • Support for Neo Coolcam NAS-WR01W WiFi Smart Power Plug
  • Support for TYWE3S-based Estink WiFi Power Strip (thanks to @sandman, #852)
  • Support for Pilotak ESP DIN V1
  • Support for DIY Geiger counter (thanks to @Trickx)
  • Support for HomeCube / Blitzwolf BW-SHP2
  • Support for Vanzavanzu Smart Wifi Plug Mini
  • Support for Bruno Horta's OnOfre board

Changed

  • Updated PlatformIO to use Core 3.5.3
  • Updated to JustWifi 2.0
  • CSS optimizations (#870, #871)
  • Several changes in OTA Manager
  • Better memory layout info
  • MQTT keep alive time increased to 300s
  • Using ticket-based authentication for WS
  • Refactor module and sensor listings (#896)
  • Using alternative math methods to save ~8Kb with lights
  • Simpligying mired/kelvin methods
  • Changed web UI checkboxes with pure CSS versions

Deprecated

  • {identifier} place-holder in MQTT base topic

[1.12.6] 2018-05-02

Fixed

  • Check NTP_SUPPORT for sensors (thanks to @mcspr)
  • Fix AM2302 sensor
  • Fix hostname truncated to 20 chars when advertised to DHCP (#774)
  • Decouple Serial object from Terminal, Debug modules (#787)
  • Fix Arilux LC-01 definitions (#797)
  • Do not uppercase hostname in web interface (#799)
  • Ensure scheduler has access to all channels independently of the color mode (#807)

Added

  • Support for IteadStudio Sonoff S31 (#497)
  • Option to ignore daylight saving in scheduler (#783)
  • Report last energy reset datetime in web interface (#784)
  • Added captive portal in AP mode
  • Support for IR toggle mode (thanks to @darshkpatel)
  • Support for IteadStudio Sonoff POW R2 (thanks to @ColinShorts)
  • Support for Luani HVIO (thanks to @wildwiz)
  • Support for Zhilde ZLD-EU55-W power strip (thanks to @wildwiz)
  • Support for RFB_DIRECT Sonoff Bridge EFM8BB1 bypass hack (thanks to @wildwiz)
  • Support for SenseAir S8 CO2 sensor (thanks to @Yonsm)
  • Support for PMS5003T/ST sensors (thanks to @Yonsm)

Changed

  • Updated JustWifi Library
  • Some cleanup in the web interface
  • Refactored configuration files (thanks to @lobradov, @mcspr)
  • Changes pre-commit hook (thanks to @mcspr)

[1.12.5] 2018-04-08

Fixed

  • Fixed expected power calibration (#676)
  • Do not show empty time strings (#691, thanks to @PieBru)
  • Fix load average calculation when system check is disabled (#707)
  • Fixed unstability issues with NtpClientLib using temporary fork (#743)
  • Fixed typos in homeassistant module (thanks to @Cabalist)
  • Fixed default HLW8012 calibration for KMC devices (thanks to @gn0st1c)
  • Fix MQTT query request
  • Fix scheduler debug message
  • Fix NTP offset value

Added

  • Option to change NTP timeout via compile-time setting (#452)
  • Added humidity correction to web UI (#626, tahnks to @ManuelW77)
  • Added support for USA DST calculation (#664)
  • Option to reset energy count (#671)
  • Added Sonoff SV prebuild image (#698, thanks to @akasma74)
  • Check and remove unused config keys (#730)
  • Visual Studio metadata files added to .gitignore (#731, thanks to @gn0st1c)
  • Added default MQTT and SSL settings to web UI (#732, thanks to @mcspr)
  • Added option to the web UI to set the light transition length in milliseconds (#739)
  • Improved testing with Travis (thanks to @lobradov)
  • Change dimmers using schedule (thanks to @wysiwyng)
  • Debug console in web UI (thanks to @lobradov), including command execution
  • Option to reset relays in MQTT disconection (thanks to @a-tom-s)
  • Option to disable system check from custom header (thanks to @phuonglm)
  • Added "board" topic to the heartbeat messages (thanks to @mcspr)
  • Added methods to create hierarchical MQTT JSON responses
  • Added RESET.SAFE command to reboot into safe mode
  • Added SDK and Core versions to the web UI
  • Added revision to web UI (only when built from build.sh)
  • Support for OBI Powerplug Adapter (#622, thanks to @Geitde)
  • Support for Tunbox Powerstrip02 (thanks to @gn0st1c)
  • Support for Lingan SWA1 (thanks to @gn0st1c)
  • Support for Heygo HY02 (thanks to @gn0st1c)
  • Support for Maxcio WUS0025 (thanks to @gn0st1c)
  • Support for Yidian XSSSA05 SWA1 (thanks to @gn0st1c)
  • Support for ArnieX Swifitch (thanks to @LubergAlexander)
  • Support for IKE ESPIKE board
  • Support for AM2320 sensors via I2C (thanks to @gn0st1c)
  • Support for GUVAS12SD sensor (thanks to @gn0st1c)

Changed

  • Removed hostname size limit (#576, #659)
  • Reworked RGBW implementation (thanks to @Skaronator)
  • Several web UI layout changes (thanks to @lobradov & @mcspr)
  • Button MQTT messages will not have the retain flag (thanks to @lobradov)
  • Remove unnecessary code from boot log (thanks to @gn0st1c)
  • Updated logo and favicon, added gitter channel
  • Force reporting power values as 0 if relay is off
  • Using gulp-crass for CSS minification
  • Using WIFI_NONE_SLEEP by default

[1.12.4] 2018-03-05

Fixed

  • Adding a 1ms delay after UDP send to avoid loosing packets (#438)
  • Fixed void return in BMX280 sensor (#489)
  • Fix MQTT keep alive cannot be more than 255 seconds (#515)
  • Do not show scheduler tab in Web UI if build without scheduler support (#527)
  • Fix inline documentation for Sonoff 4CH Pro button modes (#551)
  • Prevent resending messages from rfin in RF Bridge (#561)
  • Fix AnalogSensor description (#601)
  • Fixed missing setting in HASS WS callback (thanks to @mcspr)
  • ECH1560 call sync from tick method
  • Fixed several issues reported by codacy

Added

  • UART to MQTT module (thanks to Albert Weterings, #529)
  • Added option to show HASS configuration code in ESPurna web UI (#616)
  • OTA upgrade via terminal (using 'ota' command, with SSL support)
  • Added I2C scan and clear commands to terminal (only when I2C enabled)
  • Added new relay & wifi led mode (#604)
  • Option to enable/disable web auth from web UI
  • Added "Reset to factory settings" in web UI (thanks to Teo Pavel, #569)
  • Added {magnitude} placeholder to MQTT root topic
  • Option to report energy in kWh and power in kW (#523)
  • Check upgrade file size and signature in web UI
  • Automatically dump info on telnet connection if TERMINAL_SUPPORT is disabled
  • Two different ESPURNA_CORE images for 1MB and 4MB boards, freeing GPIOs (#557)
  • Initial support for PZEM004T sensor (still beta)
  • Support for STM_RELAY board (thanks to Maciej Czerniak)
  • Support for KMC 70011 energy monitor (thanks to Wayne Manion, #598)
  • Support for Wifi Stecker Shuko device (thanks to @Geitde, #622)
  • Support for GizWits Witty Cloud device (thanks to Theonedemon)

Changed

  • BMX280 changes to allow for hot-plug (#353)
  • Increase the initial check interval for NTP (#452)
  • Force turning relays off before turning others on when synced (#491)
  • Publish slampher as light to Home Assistant (#494)
  • Force API to return the target status of the relay (#548)
  • Increasing max number of messages in JSON payload to 20 (#588)
  • Change copy from 'Use colorpicker' to 'Use color'. Better hint. (#590)
  • Completely reworked the RF module to use the same web UI as the RFBridge module to learn new codes (#594)
  • Several spelling and grammar changes by Lee Marlow
  • Always enabled telnet access in ESPURNA_CORE image
  • Updated ESPSoftwareSerial, ESPAsyncTCP and ESPAsyncWebServer libraries

Removed

  • Remove dependency from gulp-util (#493)
  • Removed specific support for Magic Home LED Controller 2.3 (#512)
  • Disabled floating point support when building against Arduino Core 2.4.0 with PIO
  • Removed WiFi distance calculation

[1.12.3] 2018-01-29

Fixed

  • Fix telnet crash due to local reference (#487)

[1.12.2] 2018-01-29

Added

  • Repository migrated over to GitHub
  • Travis CI build test and deploy
  • Pre-commit hook to change README.md file depending on the branch
  • {hostname} and {mac} placeholders for MQTT root topic
  • Added support for timezones with minutes (#265)
  • SSDP support (#282, #423, disabled by default since current implementation is not compatible with Alexa #479)
  • HA auto-discover for multi-relay boards and sensors (#392, #465)
  • Reset the pulse timeout every time an MQTT message is sent with the non-normal payload value (#454)
  • Option to disable schedules without deleting them (#453)
  • Added LED_MODE_STATUS (#458)
  • Support to set on/off state per channel using switches (#457)
  • Added support for MagicHome LED Controller 2.3
  • Alexa message queue (thanks to Qubeck)
  • Secondary Serial RX port for H801 and H802 boards (#386, thanks to Pablo Pousada Rial)
  • Added compatibility with https://github.com/rhx/RF-Bridge-EFM8BB1 to RF Bridge (Thanks to Rene Hexel)
  • Added message queue to RF Bridge
  • Added MAC to mDNS text fields
  • Added wifi.ap command to go into AP mode
  • Added message id on MQTT JSON payloads
  • Added hooks for 3rd party code (custom modules)
  • Local broker to broadcast messages internally
  • Added timestamp to debug output
  • Common I2C interface to abstract backend library (Wire or Brzo I2C)
  • Added espurnaLoopRegister

Fixed

  • Fixed support for 4CH Pro different modes (#333)
  • Fixed several sensor modules to enable hot-unplug-plug (#398)
  • Fixed crash when calling idbSend from an MQTT callback (#410)
  • Checking trailing slash in mqttTopic (#422)
  • Fixed pulse and pulse_ms order in relay_t structure (#424)
  • Use same buffer size across all terminal-realted classes/methods. Set to 128 chars (#477, #478)
  • Fix WiFi scan status in web UI
  • Several code quality fixes (thanks to @lobradov)
  • Fixed error message on first command over telnet

Changed

  • BMX280 sensor module now doesn't depend on third party libraries
  • Changed time management in ntp, mqtt and scheduler modules

Deprecated

  • {identifier} placeholder for MQTT root topic

[1.12.1] 2018-01-14

Added

  • Option to perform a WiFi network scan from web UI
  • Added hostname to web UI side menu (#404)
  • Option to flash multiple devices with ESPurna OTA Manager

Fixed

  • Fix web UI layout so signature does not overlay buttons (#396)
  • Option to disable network scan and allow connecting to hidden SSID (#392, #399)
  • Fix crash caused by a delay in UDP debugging code (#397)
  • Fix memory leak in influxDB module (#410)
  • Fix typos in web UI (#394, #421)

Changed

  • Updated to fauxmoESP 2.4.2
  • Changed default I2C GPIO for Wemos D1 (#420)
  • Some terminal commands have changed. See docs or type "help".

[1.12.0] 2018-01-11

Added

  • Scheduler (contributed by Stefano Cotterli, thank you!, #131)
  • Added "wifi.scan" command to terminal
  • Added ESPurna Switch board support
  • Added support for python3 in memanalyzer and ota scripts (thanks to @Cabalist)
  • Added BSSID, RSSI, channels and distance to web UI status tab
  • Added mDNS name resolving to MQTT, InfluxDB and NoFUSS modules (#129, disabled by default)

Fixed

  • Update FauxmoESP library to 2.4.1, solves dependency issue (#388)
  • Fixed hardware definition in Sonoff Basic and Dual R2 causing wrong relay state on boot (#365)

Changed

  • Removed auto-recursion check in Domoticz module (#379)
  • Rename terminal commands: reset.wifi to wifi.reset, reset.mqtt to mqtt.reset.
  • Update JustWifi library to 1.1.6 (support for multiple SSIDs with the same name)
  • Changed the way Home Assistant module handles disabling auto-discovery (#383)

[1.11.4] 2018-01-09

Fixed

  • Fix bug in RF Bridge when RF code contains the stop byte. Check overflow (#357)
  • Fixed typos in code and wiki (Thanks to @Cabalist)
  • Fix bug in magnitude topic and units (#355)

Added

  • Small core build to allow two-step flashing method for big binaries
  • Thingspeak support (#371, disabled by default)
  • Color synchronization between lights using MQTT (#362)
  • Support for Arilux AL-LC02 (#347)
  • Support for Tarpuna Shield for Wemos D1
  • Build option to disable password checking (#373)
  • Option to report sensor address via MQTT (#377, I2C address, GPIO, Dallas address,...)
  • Added binary size to memanalyzer script
  • Option to specify custom client ID for MQTT connection (#368)
  • Cross-platform ESPurna OTA Manager implemented in python (untested)
  • Terminal command to get or set digital GPIO

Changed

  • Using 2.3.0 for prebuilt binaries
  • Fix delay in DHT sensor
  • Allow MQTT keep alive value of up to 3600s
  • Changed Sonoff 4CH Pro definitions to support built-in interlock mode (#333)

[1.11.3] 2018-01-02

Fixed

  • Fix uninitialized PWM channels bug (#356)

Added

  • Added memory analyzer

[1.11.2] 2017-12-30

Fixed

  • Fix my92xx and pwm references for Arduino IDE (#346)
  • Fix SHT3X I2C sensor magnitude count (#337)
  • Fix timing for DHT11 sensors (#294)
  • Fix overflow in relayParsePayload with long MQTT messages (#344)
  • Fix loading of Dallas and DHT sensors for Sonoff TH images (#352)
  • Subscribe to Domoticz MQTT topics only if Domotic< is enabled

Added

  • Added option to change MQTT retain flag, QoS and keepalive time from webUI (#321)
  • Added LED modes "always off" and "always on" (#348)
  • Defined new ESPurna switch (no HLW8012 support & touch button ready)

Changed

  • Stop requiring definition of boards in migrate module

[1.11.1] 2017-12-29

Fixed

  • Fixed relay status on reboot

Added

  • Added support for Arilux AL-LC01 and AL-LC11
  • Added support for BH1750 luminosity sensor
  • Added automatic memory size identification in ota_flash script

[1.11.0] 2017-12-28

Fixed

  • Fixed Arduino IDE compilation issues (#330)
  • Fixed issues with IE
  • Fixed websocket auth issue with Safari (temporary)
  • Fixed MQTT group sync when different switches share same group
  • Fixed casting issue in buttonStore (#327)
  • Fixed crash in InfluxDB initial heartbeat (#318)
  • Fixed LED logic for ESPurna H08 board

Added

  • New sensors module (major change)
    • Existing sensor have been migrated: EMON*, ECH1560, V9261F, HLW8012, DHT, DALLAS, ANALOG, DIGITAL and EVENTS
    • New sensor have bee added: BMP280/BME280, EMON over ADS1115, MHZ19, PMSX003 (thanks to Òscar Rovira), SHT3X over I2C and SI7021
  • Option to change boot and pulse modes per relay from the web UI
  • Option to select sensor read interval and report interval from web UI
  • Itead RF Bridge
    • Match MQTT RFOUT codes to relays
    • Force RFBridge to send messages even if switch is already in requested state (#324)
    • Implemented RFbridge message queue asynchronously
  • Added option to load config via HTTP POST & reset (#335)
  • Added option to define behaviour of the first LED between WIFI, MQTT, FIND-ME (#317)
  • Added HTML linter to gulp builder
  • Added Help command on terminal (#338)
  • Added preliminary support for SSDP (untested, disabled by default) (#282)
  • Reporting NTP datetime on MQTT heartbeat (thanks to Eldon R. Brown)
  • Added version tracking and migration code
  • I2C and GPIO locking features
  • Changed default button action for touch button devices (TOUCH and T1) (#327)
  • Generic 8 channel board (#336)

Changed

  • Added more sensor data filters (Max, MobileAverage)
  • Changed max pulse time to 1h (#316)
  • Renamed "reset" to "reboot" for clarity (#315)
  • UI refactor
  • Change apiRegister signature

[1.10.1] 2017-12-05

Fixed

  • Fix Sonoff RFBridge learn message from web UI (#287)
  • Fix unstability in "one and just one" sync mode (#290)
  • Fix unnecessary inclusion of my92xx library (#293)
  • Limit the MQTT queue to 10 messages when "Use JSON payload" enabled (#296)
  • Fix Sonoff RFBridge OFF button toggling switch (#303)
  • Allow defining only ON or OFF codes in Sonoff RFBridge (#304)
  • Disabled terminal support for Sonoff Dual (#310)

Added

  • Support for SI7021-based sensor by Itead Studio compatible with Sonoff TH (#216)
  • Support for Sonoff Dual R2 (#286)
  • MQTT group topics (sync two or more switches from different devices, #300)
  • Color transitions (enabled by default, can be disabled from web UI)
  • Option to disable MQTT support at build time

Changed

  • Decreased PWM frequency for dimmer lights
  • Changed password policy (#297)

[1.10.0] 2017-11-26

Fixed

  • Temperatures with 1 decimal resolution
  • Issues with Sonoff B1 due to bad driver management (using my92xx library now)
  • Avoid recursive messages on Domoticz (#272)
  • Fixed Sonoff T1 configuration
  • Simplify and fix web auth (#284)
  • Fix Embedis custom parser

Added

  • Added option to define a temperature correction factor (thanks to Pawel Raszewski)
  • Option to disable system check on build time
  • Power saving features (loopDelay and wifi sleep)
  • Added Sonoff TH build environment
  • Send Home Assistant auto discover messages on connect (#279)
  • Implemented Home Assistant availability topic (#280)
  • Update time, uptime and heap on webUI every heartbeat
  • Support for LLMNR and NetBIOS (#282)
  • Added I2C clean bus code
  • Added realm to auth challenge

Changed

  • Changed default hostname to "ESPURNA_XXXXXX"
  • Binaries built against stable core (~40Kb less, #274)
  • Enabled TERMINAL_SUPPORT for Sonoff Dual (only available via TELNET)
  • Dinamically resize debug strings (now messages are not cropped)
  • MQTT: unsubscribe to '#' before subscribing
  • Updated ESPAsyncWebServer and ESPAsyncTCP libraries
  • Removed InfluxDB support by default
  • Using stock slider in webUI to reduce size
  • Unify DHT and DS18B20 code, show NOT CONNECTED on webUI

[1.9.9] 2017-11-09

Fixed

  • Fixed bug in MY9291-based light bulbs at full brightness

Added

  • RFBridge: toggle when RF codes for ON and OFF are the same (#270)
  • Support for HSV color schema (MQTT, API and webUI via a selector)

Changed

  • "COLOR" entry point deprecated, use "RGB" instead (MQTT and API, ex. topic "light/rgb/set" instead of "light/color/set")

[1.9.8] 2017-11-08

Fixed

  • Removed dimmer lights flicker when saving to EEPROM (#191)
  • Fixed low brightness in dimmer lights (#157)
  • Fixed blank fields in energy (#258, #259)
  • Fixed support for Arilux AL-LC06
  • Updated fauxmoESP library with support for GetBinaryState actions

Added

  • Support for IR remotes
  • Option to select power read and report interval from webUI
  • Option to report real-time values in API, configurable via webUI
  • Support for ESPurna-H Board v0.8
  • Support for Arilux E27 light bulb (untested)
  • Support for YJZK 2-gang switch

Changed

[1.9.7] 2017-10-25

Fixed

  • Fix Alexa interface switching on all lights (#256)

[1.9.6] 2017-10-23

Fixed

  • Fix power report in Domoticz (#236)
  • Fix Sonoff POW in AP mode (#241)
  • Fix Home Automation auto-discovery (support for single relay switches and RGB lights, #235)
  • Check WS authentication only on start event

Added

  • Support for 2.4.0 RC2 Arduino Core that fixes KRACK vulnerablity (pre-built images are compiled against this, #242)
  • Support for ManCaveMade ESPLive board (thanks to Michael A. Cox)
  • Support for InterMIT Tech QuinLED 2.6 (thanks to Colin Shorts)
  • Support for Magic Home LED Controller 2.0 (thanks to users @gimi87 and @soif, #231)
  • Support for Arilux AL-LC06 (thanks to Martijn Kruissen)
  • Support for Xenon SM-PW702U Wifi boards (thanks to Joshua Harden, #212)
  • Support for Authometion LYT8266 (testing, thanks to Joe Blellik, #213)
  • Support for an external button for D1 Mini boards (thanks to user @PieBru, #239)
  • Option to query relay status via MQTT or WS (thanks to Wesley Tuzza)
  • Automatically install dependencies for web interface builder (thanks to Hermann Kraus)
  • Support for HSV and IR for Magic Home LED Controller (optional, disabled by default, thanks to Wesley Tuzza)
  • Added option to report DS18B20 temperatures based on changes (thanks to Michael A. Cox)
  • Safer buffer handling for websocket data (thanks to Hermann Kraus & Björn Bergman)
  • Updates HL8012 library with energy counting support (thanks to Hermann Kraus)
  • Added option to disable light color persistence to avoid flickering (#191)
  • Option to enable TELNET in STA mode from web UI (#203)

Changed

  • Changed default MQTT base topic to "{identifier}" (no leading slashes, #208)
  • Prevent reconnecting when in AP mode if a web session or a telnet session is active (#244)
  • Web UI checks for pending changes before reset/reconnect options (#226)
  • Increase WIFI connect timeout and reconnect interval

[1.9.5] 2017-09-28

Fixed

  • Revert to JustWifi 1.1.4 (#228)

[1.9.4] 2017-09-22

Added

  • Added ESPurna specific mDNS text registers (app_name, app_version, device_name)
  • Crash dump info is stored in EEPROM and retrieved via terminal ("crash" command)
  • Support for Huacanxing H802
  • Support for powermeters based on V9261F IC
  • Support for powermeters based on ECH1560 IC (beta, untested)

Changed

  • Changed behaviour on MQTT connection failure (#215)
  • Removed boot delay
  • Refactor power modules
  • Updated JustWifi library

Fixed

  • Set all esp8285 devices to use esp01_1m (#210, #225)
  • Removed wifi gain option since it prevents some devices to connect (#204)

[1.9.3] 2017-09-04

Added

Changed

  • Updated fauxmoESP library to 2.2.0

Fixed

  • Fix HLW8012 calibration (#194)
  • Fix telnet dropping connection
  • Fix WiFiSecureClient connection with PubSubClient (#64)

[1.9.2] 2017-08-31

Added

  • System stability check (turns off everything except WIFI AP, OTA and telnet if there is a boot crash loop) (#196)
  • Telnet support (enabled by default only on AP interface)
  • Option to set WiFi gain from web UI
  • Option to disable MQTT from web UI
  • MQTT autodiscover, with the option to autoconnect if no broker defined
  • Home Assistant MQTT autodiscover feature
  • List enabled modules in INIT debug info
  • Counter module (counts and reports transitions in a digital pin)

Changed

  • Updated NoFUSS support
  • Web UI documentation changes
  • Changes in terminal commands ("reconnect" is now "reset.wifi", also new commands added)

Fixed

  • Crash in settings saving (#190) and fixed UDP debug conditional build clauses

[1.9.1] 2017-08-27

Added

  • Support to build without NTP support
  • Added current time, uptime, free heap, firmware size and free space to web interface

Changed

  • Changed settings keys for Itead Sonoff RF Bridge
  • Disable Domoticz by default

Fixed

  • Fixed build flags for DHT and DS18B20 in platformio.ini file
  • Fixed Itead Sonoff B1 by updating the my9291 library
  • Fixed light status on boot (#157)
  • Fixed CSS bug cause by a bad merge

[1.9.0] 2017-08-25

Added

  • Support for IteadStudio BN-SZ01 Ceiling Light (#132)
  • Support for IteadStudio Sonoff RF Bridge (#173)
  • Support for IteadStudio Sonoff 4CH Pro (#174)
  • Support for IteadStudio Sonoff B1
  • Support for IteadStudio Sonoff LED
  • Support for IteadStudio Sonoff T1 wall switches (1, 2 and 4 channels)
  • Support for WiOn 50055 WiFi Wall Outlet & Tap
  • Support for EXS WiFi Relay v3.1 (and other future latching relay boards) (#152)
  • TLS/SSL support for MQTT (caution: eats a lot of memory, do not use with web interface) (#64)
  • Add support for delayed ON/OFF switches (#123, #161, #188)
  • Added ON and OFF actions for button events (previously only TOGGLE available) (#182)
  • Sliders in web interface to control dimmer channels independently (also for brightness)
  • Debug info about MQTT disconnect reason

Changed

  • MQTT setters ending with "/set" by default
  • Using DOUT flash mode on all devices (#167)
  • Longer timeout for WiFi connection (better chances for Sonoff Basic to connect)
  • Changed MQTT topics for light devices (COLOR, BRIGHTNESS, MIRED, KELVIN, CHANNEL) (#144)
  • Changed the way light devices are defined (see LIGHT_PROVIDER_DIMMER)
  • Allow to disable color picker in web interface
  • API returns processed values for HLW8012 sensor (not raw values anymore) (#176)
  • Major refactoring of settings

Fixed

[1.8.3] 2017-07-23

Added

  • Issue #85 and #90. Option to report MQTT messages with JSON payloads
  • Issue #170. Updated DebouceEvent library to allow disabling double click and get faster click responses
  • Using memory layout with no SPIFFS for 1Mb devices

Changed

  • Rename settings s/POW/HLW8012/
  • Return times in ISO8601 format

Fixed

  • Issue #168. Added H801 to arduino.h file
  • Issue #171. Fix corrupted will message

[1.8.2] 2017-07-16

Added

  • InfluxDB support via HTTP API
  • Added custom reset reason to debug log
  • Enable WIFI debug on hardware reset (button long click)

Changed

  • Issue #159. Allow decimals in relay pulse interval
  • Updated HLW8012 library

Fixed

  • Issue #148. Fix bug in conditional compilation check
  • Issue #149. Using different pulse counters for each relay (thanks to Lauris Ieviņš)
  • Issue #141. Limit relay pulse interval to 60s
  • Fixed units for apparent & reactive power (thanks to Lauris Ieviņš)
  • Fixed mDNS setup when using custom HTTP port for web interface

[1.8.1] 2017-05-22

Fixed

  • Issue #140. Fix no relay control bug in Sonoff Dual

[1.8.0] 2017-05-21

Added

  • Added gamma correction to RGB strips. Thanks to Chris Ward.
  • Added support for Huacanxing H801 WiFi LED Controller. Thanks to Minh Phuong Ly.
  • Issue #138. Added NTP configuration from web interface
  • Issue #128. Report color when booting and in heartbeat stream.
  • Issue #126. Show NTP status in web interface.
  • Added filter limits on POW readings.
  • Added color temperature to RGB calculation. Thanks to Sacha Telgenhof.
  • Issue #120. Added relay flood protection. Thanks to Izik Dubnov.
  • Support for "#RRGGBB", "RRR,GGG,BBB" and "WWW" color formats.
  • Issue #117. Added build date & time to web interface.

Fixed

  • Fix MQTT_RELAY board conifugration. Thanks to Denis French.
  • Issue #125. Fix bug in relay status reading from EEPROM
  • Issue #127. Fix button action in DUAL.
  • Fix bug in Sonoff POW current reading. Thanks to Emmanuel Tatto.
  • Minimizing my9291 flickering when booting.
  • Fix conditional flags in hardware.ino to support Arduino IDE.

[1.7.1] 2017-03-28

Fixed

  • Issue #113. Fix restoring color from EEPROM upon reboot
  • Issue #113. Fix bug in API handlers

[1.7.0] 2017-03-27

Added

  • Web interface embedded in firmware image by default
  • Upload firmware image from web interface
  • Added API entry point to change light color
  • Added generic analog sensor. Thanks to Francesco Boscarino
  • Report RSSI value in debug console and MQTT status messages
  • Added support for Magic Home LED Controller
  • Added support for ESPurna-H Board (based on HLW8012)
  • Added forward compatible code for v2.0

Changed

  • Added ellipsis (...) in debug messages longer than 80 characters
  • Changed topic constants in code
  • Prevent the SDK from saving WiFi configuration to flash

Fixed

  • Issue #113. Fix light bulb state to OFF in library prevented the bulb from turning on
  • Issue #58. Added code to handle spurious readings
  • Fix bug in HLW8012 calibration current parameter casting to int instead of float
  • Issue #115. Removed local declaration of _mqttForward variable. Thanks to Paweł Fiedor
  • Fix MQTT will topic. Thanks to Asbjorn Tronhus

[1.6.9] 2017-03-12

Added

  • Two stage read for DS18B20 devices. Thanks to Izik Dubnov.
  • Option to report the relay status via MQTT periodically
  • Terminal commands to change relay status an light color
  • Added debug via UDP (disabled by default)
  • Moved debug strings to PROGMEM. ~1.5KByes memory freed
  • Avoid broadcasting websocket messages if no clients connected

Fixed

  • Fixing use after free bug that leads to corrupted auth credentials. Thanks to David Guillen

[1.6.8] 2017-03-01

Added

  • Issue #85. Heartbeat reports now free heap, uptime and VCC every 5 minutes

Changed

  • Wait two minutes instead of one in AP mode before trying to reconnect to the router
  • Issue #92. Debug log enabled by default in Arduino IDE
  • Issue #91. Using AsyncMqttClient as default MQTT client again

Fixed

  • Report data from all sensors via websocket even if no MQTT connection
  • Issue #92. Fix unknown reference in Arduino IDE
  • Split data.h contents into 1k lines, otherwise Arduino IDE chokes on them
  • Discard empty MQTT topic while subscribing

[1.6.7] 2017-02-25

Added

  • Support for OpenLight / AI-Light by AI-Thinker based on MY9291 LED driver
  • Issue #87. Factory reset when physical button pressed for >10 seconds

[1.6.6] 2017-02-23

Fixed

  • Issue #82. Fix critical bug on Sonoff Dual

[1.6.5] 2017-02-22

Added

  • Option to backup and restore settings from the web interface
  • Footer in the web interface

Changed

  • Using PubSubClient as MQTT client by default (please read the documentation)
  • Double & long clicks do nothing except for the first defined button

Fixed

  • Issue #79. Fix bug in WiFi led notification & MQTT connectivity (using PubSubClient)
  • Issue #73. Fix bug when building without Domoticz support
  • Fix Gulp tasks dependencies

[1.6.4] 2017-02-20

Added

  • Option to embed the web interface in the firmware, disabled by default
  • Change relay status with a GET request (browser friendly)
  • Support for PROGMEM debug messages (only wifi module has been changed)
  • Option to disable mDNS, enabled by default
  • Show current web server port in debug log
  • Issue #75. Link relays to LEDs
  • Issue #76. Using http://espurna.local when in AP mode

Changed

  • Images and favicon is now embedded in the HTML
  • Authentication challenge only in /auth request. All static contents are un-authenticated
  • HTTP response code when out of websocket slots changed from 423 to 429

Fixed

  • Memory leak in MQTT connection method
  • Wait 60 seconds before retrying to connect when in AP mode
  • Issue #24 & #74. Update ESPAsyncTCP and ESPAsyncWebServer to latest GIT version that supports MSS defragmenting
  • Issue #73. Fixes for windows machines

Removed

  • Captive portal removed, mDNS resolution for AP mode too

[1.6.3] 2017-02-15

Added

  • Issue #69. Temperature unit configuration from the web interface
  • Issue #55. WebServer port configurable from the web interface, defaults to 80
  • Expand network configuration when adding a new network

Changed

  • Merged web contents except images in a single compressed file for reliability
  • Update support for Itead Motor Clockwise/Anticlockwise board
  • Scan for strongest network only if more than 1 network configured

Fixed

  • Issue #71. Added default values for netmask and DNS in web configuration
  • Fixed Itead 1CH self-locking/inching board definition
  • Fixed PlatformIO environments for ESP8285 boards (4CH and Touch)

[1.6.2] 2017-02-10

Fixed

  • Check if there is an MQTT broker defined before the MQTT_MAX_TRIES check

[1.6.1] 2017-02-10

Added

  • Added support for Jorge Garcia's Wifi+Relay Board Kit
  • Reporting current and energy incrementals to a separate counters in Domoticz (thanks to Toni Arte)
  • Force WiFi reconnect after MQTT_MAX_TRIES fails trying to connect to MQTT broker

[1.6.0] 2017-02-05

Added

  • Added support for toggle switches
  • Allow reset the board via an MQTT message
  • Allow reset the board via an RPC (HTTP) message
  • Added support for ADC121 I2C for current monitoring (Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/)
  • Reporting voltage to Domoticz (only HLW8012)
  • Map button events to actions (toggle relay, AP mode, reset, pulse mode)

Changed

  • Reporting energy incrementals (Domoticz, MQTT)

Removed

  • Removed current monitor bypass when relay is OFF
  • Removed energy API entry point

[1.5.4] 2017-02-03

Fixed

  • Issue #50. Fix type bug in window variable when calculating energy for HLW8012 devices (Sonoff POW)

[1.5.3] 2017-02-02

Fixed

  • Issue #50 and #54. Fixed domoticz MQTT message format

Added

  • Energy calculation and aggregation. API entry points and MQTT messages.

[1.5.2] 2017-01-29

Fixed

  • Fix bug in emon topic payload

[1.5.1] 2017-01-28

Added

  • OpenEnergyMonitor WiFi MQTT Relay / Thermostat support (thanks to Denis French)

Fixed

  • NTP connection refresh upon wifi connection
  • Filesystem image build using local gulp installation

[1.5.0] 2017-01-21

Added

  • Pulse mode. Allows to define a pulse time after which the relay will switch back
  • API entry points for sensor data (power, current, voltage, temperature and humidity)
  • Export sensor data to Domoticz (power, current, voltage, temperature and humidity)
  • Configurable (in code) mapping between buttons and relays
  • MQTT messages for button events
  • Added support for Itead Studio 1CH inching/self locking smart switch board
  • Added support for Jan Goedeke Wifi Relay boards (both NC and NO versions)
  • Notify OTA updates to websocket clients, automatically reload page
  • Support for pulse mode notification LED and button
  • Revert relay state mode on boot (thanks to Minh Phuong Ly)

Fixed

  • MQTT will topic
  • Crash with HLW812 interrupts while trying to create a WIFI connection
  • Issue #20 Better inline documentation for Alexa and Domoticz default settings
  • Issue #39 Fixed autoconnect issue with static IP (fixed in JustWifi library)
  • Issue #41 Added password requirements to initial password change page

Changed

  • Changed LED pattern for WIFI notifications (shorter pulses)

[1.4.4] 2017-01-13

Added

  • Adding current, voltage, apparent and reactive power reports to Sonoff POW (Web & MQTT)

Fixed

  • Issue #35 Fixed frequent MQTT connection drops after WIFI reconnect
  • Defer wifi disconnection from web interface to allow request to return

Changed

  • Move all Arduino IDE configuration values to their own file
  • Using latest HLW8012 library in interrupt mode

[1.4.3] 2017-01-11

Fixed

  • Issue #6 Using forked Time library to prevent conflict with Arduino Core for ESP8266 time.h file in windows machines

[1.4.2] 2017-01-09

Added

  • Support for inverse logic relays

Fixed

  • Issue #31. Fixed error in relay identification from MQTT messages

[1.4.1] 2017-01-05

Added

  • Alexa support by default on all devices
  • Added support for Wemos D1 Mini board with official Relay Shield

Fixed

  • Multi-packet websocket frames

[1.4.0] 2016-12-31

Added

Fixed

  • Issue #16. Enforce minimum password strength in web interface

Changed

  • Using default client_id provided by AsyncMqttClient
  • Allow up to 5 different WIFI networks

Removed

  • File system version file

[1.3.1] 2016-12-31

Fixed

  • data_dir fix for PlatformIO

[1.3.0] 2016-12-30

Changed

  • Arduino IDE support (changes in the folder structure and documentation)

[1.2.0] 2016-12-27

Added

  • Force password changing if it's the default one
  • Added Last-Modified header to static contents
  • Added DNS captive portal for AP mode
  • Added support for Sonoff 4CH
  • Added support for WorkChoice ecoPlug (ECOPLUG). Thanks to David Myers
  • Added support for Sonoff SV
  • Added support for Sonoff Touch
  • Comment out hardware selection in hardware.h if using Arduino IDE
  • Added support for MQTT get/set suffixes (/status, /set, ...)
  • Added support for LED notifications via MQTT
  • Added EEPROM check commands to terminal interface

Changed

  • Using unreleased AsyncMqttClient with stability improvements
  • Better decoupling between MQTT and relays/websockets
  • Skipping retained MQTT messages (configurable)

Fixed

  • Issue #11 Compile error when building sonoff-dual-debug
  • Issue #14 MQTT Connection with Username an Password not working
  • Issue #17 Moved static variable 'pending' to class variable

[1.1.0] 2016-12-06

Added

  • Added support for DS18B20 temperature sensor. Thanks to Francesco Boscarino
  • Added reset command from console
  • Added support for multirelay boards like Sonoff DUAL or Electrodragon ESP Relay Board

Changed

  • Not using espressif8266_stage in default environment
  • Relay MQTT topics
  • API entry points

Removed

  • Old non protected API

[1.0.3] 2016-11-29

Added

  • WeMo emulation through the fauxmoESP library (control your switch from Alexa!)
  • REST API for relay management
  • Better dependency definitions in platformio.ini
  • Option to define inverse logic to on-board LED
  • Built data folder included in repo

Changed

  • Using non-interrupt driven mode for HLW8012
  • Better documentation
  • Small changes to web interface
  • Same admin password for web, OTA and WIFI AP mode

Fixed

  • Prevent fauxmoESP to be compiled by default

Removed

  • Removed ESPurna board to its own repo

[1.0.1] 2016-11-13

Added

  • Basic authentication and CSRF to websocket requests

[1.0.0] 2016-11-13

Added

  • Using ESPAsyncWebServer (for web & websockets) and AsyncMqttClient

[0.9.9] 2016-11-12

Added

  • Preliminary support for Sonoff POW
  • Replace AJAX requests with websockets
  • Using sprites for images
  • Hostname can be changed
  • Added initial relay state mode
  • Reconnect and reset buttons on web interface

Changed

  • Changed long click to reset and double click to AP mode
  • Using officially supported platformio.ini file by default

Fixed

[0.9.8] 2016-10-06

Added

  • Using PureCMS for the web interface
  • Using gulp to build the filesystem files
  • Using Embedis for configuration

Changed

  • Updated JustWifi library
  • Web interface changes
  • Using custom platformio.ini file
  • Loads of changes in modules
  • Added DEBUG_MSG

Fixed

  • Clean gulp builder script

[0.9.7] 2016-08-28

Changed

  • Moving wifi management to library (JustWifi)
  • Split code into modules

[0.9.6] 2016-08-12

Added

  • Added heartbeat, version and fsversion MQTT messages

Changed

  • GZip 3rd party contents

[0.9.5] 2016-07-31

  • Initial stable version