-
Notifications
You must be signed in to change notification settings - Fork 3
/
amttool.man
100 lines (100 loc) · 2.36 KB
/
amttool.man
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
.TH amttool 1 "(c) 2007,08 Gerd Hoffmann"
.SH NAME
amttool - remotely control Intel AMT managed machines.
.SH SYNOPSIS
.B amttool host [ command ] [ arg(s) ]
.SH DESCRIPTION
.B amttool
is a perl script which speaks SOAP to Intel AMT managed machines.
It can query informations about the machine in question and also
send some commands for basic remote control.
.P
.B host
is the hostname or IP address of the machine amttool should
control.
.B command
is an optional command.
.P
You must set fill AMT_PASSWORD environment variable with the AMT
password.
.P
For more inforamtions on Intel AMT check amt-howto(7).
.P
.B Note:
Starting with AMT 9.0 Intel has removed support for
the old SOAP protocol which is used by amttool.
Only WS Management (added in AMT 3.0) is supported by recent
machines. You can use wsmancli (see http://openwsman.sf.net,
your distro should have packages ready) instead.
.SH COMMANDS
.TP
.B info
gather information (default).
.TP
.B reset [ special ]
reset machine, with optional special command (see section below).
.TP
.B powerup [ special ]
turn on machine.
.TP
.B powerdown
turn off machine.
.TP
.B powercycle [ special ]
powercycle machine.
.TP
.B netinfo
print network configuration (requires AMT 2.5+).
.TP
.B netconf if link [ ip mask gw [ dns1 [ dns2 ]]]
configure network interface (requires AMT 2.5+).
.B if
is the interface handle,
.B link
the link policy. If in doubt just feed in what the netinfo command
prints.
.B ip
is the IPv4 address,
.B mask
the netmask,
.B gw
the default gateway,
.B dns1
and
.B dns2
are the DNS Servers. If no IP configuration is specified the tool
tries to configure the machine in shared mac address mode with dhcp,
otherwise in separate mac address mode with static IP address.
Default for dns1 is the gateway address, for dns2 it is 0.0.0.0.
.SH SPECIAL COMMANDS
Special commands can optionally be specified for reset, powerup and
powercycle. They change the default boot behavior of the machine.
.TP
.B bios
Asks for the BIOS boot messages being redirected to serial-over-lan.
.TP
.B pxe
Network boot via PXE.
.TP
.B hd
Boot from local disk.
.TP
.B hdsafe
Boot from local disk (safe mode).
.TP
.B cd
Boot from CD/DVD.
.TP
.B diag
Boot in diagnostics mode.
.SH ENVIRONMENT
.TP
.B AMT_PASSWORD
AMT password.
.TP
.B AMT_DEBUG
Enable debug output.
.SH SEE ALSO
amtterm(1), gamt(1), amt-howto(7)
.SH AUTHOR
(c) 2007 Gerd Hoffmann <[email protected]>