From cd878b1b55b669e95237732f5780e0907e2bb222 Mon Sep 17 00:00:00 2001 From: Sander Vanheule Date: Sat, 24 Jun 2023 22:18:35 +0200 Subject: [PATCH] ramips: mt7621: add TP-Link EAP613 v1 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule (cherry picked from commit 11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5) --- .../ramips/dts/mt7621_tplink_eap613-v1.dts | 151 ++++++++++++++++++ target/linux/ramips/image/mt7621.mk | 13 ++ .../mt7621/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 1 + 4 files changed, 166 insertions(+) create mode 100644 target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts diff --git a/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts b/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts new file mode 100644 index 000000000000..d25bf5756022 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "tplink,eap613-v1", "mediatek,mt7621-soc"; + model = "TP-Link EAP613 v1"; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led_status: status { + label = "blue:status"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "partition-table"; + reg = <0x80000 0x10000>; + read-only; + }; + + partition@90000 { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + label = "product-info"; + reg = <0x90000 0x10000>; + read-only; + + macaddr: macaddr@8 { + reg = <0x8 0x6>; + }; + }; + + partition@a0000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0xa0000 0xcf0000>; + }; + + partition@d90000 { + label = "user-config"; + reg = <0xd90000 0x60000>; + read-only; + }; + + partition@f30000 { + label = "mutil-log"; + reg = <0xf30000 0x80000>; + read-only; + }; + + partition@fb0000 { + label = "oops"; + reg = <0xfb0000 0x40000>; + read-only; + }; + + radio: partition@ff0000 { + label = "radio"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&state_default { + gpio { + groups = "uart3"; + function = "gpio"; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&radio 0x0>; + mediatek,disable-radar-background; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr>; + nvmem-cell-names = "mac-address"; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index e426eac5b6ef..fa4c83dbe18d 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -2132,6 +2132,19 @@ define Device/tplink_eap235-wall-v1 endef TARGET_DEVICES += tplink_eap235-wall-v1 +define Device/tplink_eap613-v1 + $(Device/dsa-migration) + $(Device/tplink-safeloader) + DEVICE_MODEL := EAP613 + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools + TPLINK_BOARD_ID := EAP610-V3 + KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k + KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd + IMAGE_SIZE := 13248k +endef +TARGET_DEVICES += tplink_eap613-v1 + define Device/tplink_eap615-wall-v1 $(Device/dsa-migration) $(Device/tplink-safeloader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index cd746e84eeae..6057c171922e 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -24,6 +24,7 @@ ramips_setup_interfaces() sercomm,na502|\ sercomm,na502s|\ thunder,timecloud|\ + tplink,eap613-v1|\ tplink,re350-v1|\ tplink,re500-v1|\ tplink,re650-v1|\ diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 80c727354300..3467e783f048 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -158,6 +158,7 @@ case "$board" in hw_mac_addr="$(mtd_get_mac_binary factory 0x4)" [ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 4 > /sys${DEVPATH}/macaddress ;; + tplink,eap613-v1|\ tplink,eap615-wall-v1) hw_mac_addr="$(mtd_get_mac_binary product-info 0x8)" macaddr_add "$hw_mac_addr" "$PHYNBR" > "/sys${DEVPATH}/macaddress"