| layout | title |
|---|---|
documentation |
ZW116 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZW116, manufactured by AEON Labs with the thing type UID of aeon_zw116_02_001.
This version of the device is limited to firmware versions above 2.1
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZW116 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Aeotec Nano Switch is a Z-Wave Smart Switch specifically used to enable Z-Wave command and control (on/off) of any wall switches. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the unit’s operating status.
It can connect to 2 external manual switches to control the load ON/OFF independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Dual Nano Switch.
The Nano Switch is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
Including Nano Switch as a non-secure device
If you want your Nano Switch as a non-secure device in your Z-Wave network, press the Action Button once on Nano Switch when you pair it to your gateway. If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colourful gradient.
Including Nano Switch as a secure device
In order to take full advantage of the Nano Switch, you will want your Nano Switch as a security device that uses encrypted messages to communicate in your Z-wave network. A security enabled controller/ gateway (or Z-Wave Plus controller) is required.
- Set your Z-Wave Plus controller into pairing mode.
- Press the Action Button 2 times within 1 second on the Nano Switch, the blue LED (secure indication) will blink to indicate the Nano Switch is entering into secure pairing mode.
- If the Nano Switch has been successfully added to your Z-Wave network, its RGB LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colourful gradient, repeat the instructions above from step 1.
Your Nano Switch can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective section within your controller instruction manual.
- Set your Z-Wave controller into removal mode.
- Press the Action Button on the Nano Switch or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colourful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load), repeat the instructions above from step 1.
Reset your Nano Switch.
If at some stage, your primary controller is missing or inoperable, you may wish to reset all of your Nano Switch’s settings to their factory defaults. To do this, press and hold the Action Button for 20 seconds and then release it. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colourful gradient status as a confirmation
The following table summarises the channels available for the ZW116 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number | |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (amps) | meter_current | meter_current | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number |
| Reset Meter | meter_reset | meter_reset | Energy | Switch |
| Alarm (heat) | alarm_heat | alarm_heat | Fire | Switch |
| Alarm (power) | alarm_power | alarm_power | Energy | Switch |
| Clock Time Offset | time_offset | time_offset | Time | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current channel is of type meter_current and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage channel is of type meter_voltage and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Reset the meter.
The meter_reset channel is of type meter_reset and supports the Switch item and is in the Energy category.
Indicates if a heat alarm is triggered.
The alarm_heat channel is of type alarm_heat and supports the Switch item and is in the Fire category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if a power alarm is triggered.
The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Provides the current time difference for the devices time.
The time_offset channel is of type time_offset and supports the Number item and is in the Time category.
The following table provides a summary of the 29 configuration parameters available in the ZW116. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | Current Overload Protection | Current Overload Protection |
| 4 | Overheat protection | Overheat protection |
| 9 | Instant Energy Autosend Interval | Instant Energy Autosend Interval (SENSOR_MULTILEVEL_REPORT) |
| 20 | Output status after re-power | Configure the output status after re-power on it |
| 80 | Group 1 notifications | Group 1 notifications when the state of Nano Switch's load is changed. |
| 81 | Group 3 notifications | Notification to sent for Group 3 when using the external switch 1 |
| 82 | Group 4 notifications | Notification to sent for Group 4 when using the external switch 2 |
| 83 | Configure the state of LED | Configure the state of LED when it is in 3 modes |
| 84 | Night light mode LED state | Set the ON/OFF time of the LED when it is in Night light mode |
| 86 | Set appointment 1 | Set the ON time of output load. |
| 87 | Set appointment 2 | Set the OFF time of output load |
| 90 | Enables/disables parameter 91 and 92 | Enables/disables parameter 91 and 92 |
| 91 | Set the threshold value of wattage | Threshold change in wattage (in terms of wattage) to induce an automatic report |
| 92 | Set the threshold value of percent power | Threshold percentage change in wattage for an automatic report |
| 100 | Set parameter 101-103 to default value | Reset the parameter 101-103 |
| 101 | Set group 1 reports | To set which reports need to be sent in Report group 1. |
| 102 | Set group 2 reports | To set which reports need to be sent in Report group 2. |
| 103 | Set group 3 reports | To set which reports need to be sent in Report group 3. |
| 110 | Reset the parameter 111-113 | Set parameter 111-113 to default value. |
| 111 | Interval for automatic report group 1. | Set the interval of automatic report for Report group 1. |
| 112 | Interval for automatic report group 2 | Set the interval of automatic report for Report group 2. |
| 113 | Interval for automatic group 3 report | Set the interval of automatic report for Report group 3 |
| 120 | External switch mode for S1 | Configure the external switch mode for S1 |
| 121 | External switch mode for S2 | Configure the external switch mode for S2 |
| 122 | Control destination of external switch | Set the control destination for external switch |
| 247 | Set S1 switching behaviour | Set S1 switching behaviour when the Switch mode is 2 state switch mode. |
| 247 | Set S2 switching behaviour | Set S2 switching behaviour when the Switch mode is 2 state switch mode. |
| 252 | Lock/unlock configuration parameters | Lock/unlock configuration parameters |
| 255 | Reset the Nano Switch | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Current Overload Protection
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
| 1 | (Default) Enable |
The manufacturer defined default value is 1 ((Default) Enable).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Overheat protection
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | (Default) Disable |
| 1 | Enable |
The manufacturer defined default value is 0 ((Default) Disable).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Instant Energy Autosend Interval (SENSOR_MULTILEVEL_REPORT) Send SENSOR_MULTILEVEL_REPORT at this interval
0 means to not send Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Configure the output status after re-power on it
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Last status |
| 1 | Always on |
| 2 | Always off |
The manufacturer defined default value is 0 (Last status).
This parameter has the configuration ID config_20_1 and is of type INTEGER.
Group 1 notifications when the state of Nano Switch's load is changed. To set which notification would be sent to the associated devices (Group 1) when the state of Nano Switch's load is changed. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Send Nothing |
| 1 | Send Hail CC |
| 2 | Send Basic Report CC |
| 3 | Send Hail CC when using the manual switch |
The manufacturer defined default value is 3 (Send Hail CC when using the manual switch ).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
Notification to sent for Group 3 when using the external switch 1 To set which notification would be sent to the associated nodes in association Group 3 when using the external switch 1 to switch the loads. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Send Nothing |
| 1 | Send Basic Set CC |
The manufacturer defined default value is 1 (Send Basic Set CC).
This parameter has the configuration ID config_81_1 and is of type INTEGER.
Notification to sent for Group 4 when using the external switch 2 To set which notification would be sent to the associated nodes in association Group 4 when using the external switch 2 to switch the loads. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Send Nothing |
| 1 | Send Basic Set CC |
The manufacturer defined default value is 1 (Send Basic Set CC).
This parameter has the configuration ID config_82_1 and is of type INTEGER.
Configure the state of LED when it is in 3 modes Configure the state of LED when it is in 3 modes (Energy mode, Momentary indicate mode, Night light mode) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Energy mode. |
| 1 | Momentary indicate mode |
| 2 | Night light mode. The LED will remain ON state |
The manufacturer defined default value is 0 (Energy mode.).
This parameter has the configuration ID config_83_1 and is of type INTEGER.
Set the ON/OFF time of the LED when it is in Night light mode 0 to 60 The minute time of OFF 256 to 316 The hour time of OFF 65536 to 65596 The minute time of ON 16777216 to 16777276 The hour time of ON Values in the range 0 to 2147483647 may be set.
The manufacturer defined default value is 301991936.
This parameter has the configuration ID config_84_4 and is of type INTEGER.
Set the ON time of output load. 65536 to 65543 The day value (Mon to Sun) 16777216 Enable the setting. 256 to 316 The hour value of ON time 16777215 Disable the setting. 0 to 60 The minute value of ON time Values in the range 0 to 8327680 may be set.
The manufacturer defined default value is 8327680.
This parameter has the configuration ID config_86_4 and is of type INTEGER.
Set the OFF time of output load 256 to 316 The hour value of ON time 65536 to 65543 The day value (Mon to Sun) 16777215 Disable the setting. 0 to 60 The minute value of ON time 16777216 Enable the setting. Values in the range 0 to 8327680 may be set.
The manufacturer defined default value is 8327680.
This parameter has the configuration ID config_87_4 and is of type INTEGER.
Enables/disables parameter 91 and 92
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | (Default) Disable |
| 1 | Enable |
The manufacturer defined default value is 0 ((Default) Disable).
This parameter has the configuration ID config_90_1 and is of type INTEGER.
Threshold change in wattage (in terms of wattage) to induce an automatic report
Values in the range 0 to 60000 may be set.
The manufacturer defined default value is 25.
This parameter has the configuration ID config_91_2 and is of type INTEGER.
Threshold percentage change in wattage for an automatic report
Values in the range 0 to 100 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_92_1 and is of type INTEGER.
Reset the parameter 101-103
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_100_1_wo and is of type INTEGER.
This is a write only parameter.
To set which reports need to be sent in Report group 1.
The following option values may be configured, in addition to values in the range 0 to 15 -:
| Value | Description |
|---|---|
| 1 | Send Meter Report of energy (kWh) |
| 2 | Send Meter Report of wattage (W) |
| 4 | Send Meter Report of voltage (V) |
| 8 | Send Meter Report of current (A) |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_101_4 and is of type INTEGER.
To set which reports need to be sent in Report group 2.
The following option values may be configured, in addition to values in the range 0 to 15 -:
| Value | Description |
|---|---|
| 1 | Send Meter Report of energy (kWh) |
| 2 | Send Meter Report of wattage (W) |
| 4 | Send Meter Report of voltage (V) |
| 8 | Send Meter Report of current (A) |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_102_4 and is of type INTEGER.
To set which reports need to be sent in Report group 3.
The following option values may be configured, in addition to values in the range 0 to 15 -:
| Value | Description |
|---|---|
| 1 | Send Meter Report of voltage (V) |
| 2 | Send Meter Report of current (A) |
| 4 | Send Meter Report of wattage (W) |
| 8 | Send Meter Report of energy (kWh) |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_103_4 and is of type INTEGER.
Set parameter 111-113 to default value.
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_110_1_wo and is of type INTEGER.
This is a write only parameter.
Set the interval of automatic report for Report group 1.
Values in the range 1 to 2147483647 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_111_4 and is of type INTEGER.
Set the interval of automatic report for Report group 2.
Values in the range 1 to 2147483647 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_112_4 and is of type INTEGER.
Set the interval of automatic report for Report group 3
Values in the range 1 to 2147483647 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_113_4 and is of type INTEGER.
Configure the external switch mode for S1
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Enter automatic identification mode |
| 1 | 2-state switch mode |
| 2 | 3 way switch mode |
| 3 | Momentary push button mode |
The manufacturer defined default value is 0 (Enter automatic identification mode).
This parameter has the configuration ID config_120_1 and is of type INTEGER.
Configure the external switch mode for S2
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Enter automatic identification mode |
| 1 | 2-state switch mode |
| 2 | 3 way switch mode |
| 3 | Momentary push button mode |
The manufacturer defined default value is 0 (Enter automatic identification mode).
This parameter has the configuration ID config_121_1 and is of type INTEGER.
Set the control destination for external switch
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | control the output loads of itself |
| 2 | control the other nodes |
| 3 | control the output loads of itself and other nodes |
The manufacturer defined default value is 3 (control the output loads of itself and other nodes).
This parameter has the configuration ID config_122_1 and is of type INTEGER.
Set S1 switching behaviour when the Switch mode is 2 state switch mode.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | S1 is a toggle switch |
| 1 | S1 is an on/off switch |
The manufacturer defined default value is 0 (S1 is a toggle switch).
This parameter has the configuration ID config_247_1_0000000F and is of type INTEGER.
Set S2 switching behaviour when the Switch mode is 2 state switch mode.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | S2 is a toggle switch |
| 1 | S2 is an on/off switch |
The manufacturer defined default value is 0 (S2 is a toggle switch).
This parameter has the configuration ID config_247_1_000000F0 and is of type INTEGER.
Lock/unlock configuration parameters
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Unlock |
| 1 | Lock |
The manufacturer defined default value is 0 (Unlock).
This parameter has the configuration ID config_252_1 and is of type INTEGER.
This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | (Default) Reset all configuration parameters |
| 1431655765 | Reset and remove from network |
The manufacturer defined default value is 0 ((Default) Reset all configuration parameters).
This parameter has the configuration ID config_255_4 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZW116 supports 4 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. When the load state of Nano Switch (turn on/off the load) is changed, the Hail CC and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group.
Association group 1 supports 5 nodes.
Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Dual Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller.
(E.g. Send/forward Basic Set to control the other nodes in association Group 2)
Association group 2 supports 5 nodes.
Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated.
Note: The Switch Mode of external switch S1 should be identified successfully, which means that the value of Configuration parameter 0x78 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S1 switch.
Association group 3 supports 5 nodes.
Association group 4 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_CLOCK_V1 | |
| COMMAND_CLASS_HAIL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.