| layout | title |
|---|---|
documentation |
PD300Z-2 - ZWave |
{% include base.html %}
This describes the Z-Wave device PD300Z-2, manufactured by Linear Corp with the thing type UID of linear_pd300z2_00_000.
The device is in the category of Light Bulb, defining Devices that illuminate something, such as bulbs, etc..
The PD300Z-2 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
300 Watt, 120 VAC NWI and Scene Capable Plug-In Lamp Module
- Prepare the Controller to include a unit to the network. The PD300Z-2 must be in its permanently installed location.
- For NWI Inclusion, press the button on the PD300Z-2 once.
- For classic inclusion, press the button on the PD300Z-2 twice.
- Set the Controller into Removal Mode
- Remove the switch by press the button twice
The following table summarises the channels available for the PD300Z-2 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
The following table provides a summary of the 1 configuration parameters available in the PD300Z-2. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 29 | Load Sense | Turn load sense on with 1, off with 0 |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Turn load sense on with 1, off with 0 Set parameter to 0 to disable load sense, set parameter to 1 to enable load sense. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable load sense |
| 1 | Enable load sense |
The manufacturer defined default value is 1 (Enable load sense).
This parameter has the configuration ID config_29_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.