| layout | title |
|---|---|
documentation |
ZXT-310 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZXT-310, manufactured by Remotec with the thing type UID of remotec_zxt310_00_000.
The device is in the category of Remote Control, defining Any portable or hand-held device that controls the status of something, e.g. remote control, keyfob etc..
The ZXT-310 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
ZXT‐310 is a Z‐Wave‐to‐AV IR Extender (Figure 1) and it works with any Z‐Wave compliant controller or gateway by translating Z‐Wave Simple AV command
Press the PROG button
Press the PROG button
The following table summarises the channels available for the ZXT-310 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|
The following table provides a summary of the 3 configuration parameters available in the ZXT-310. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | UIRD | parameter 1 - 20 (0x01 - 0x14) |
| 21 | The Simple AV command | The Simple AV command number or key going to be downloaded to the ZXT‐310 |
| 22 | Download status register | Download status register |
parameter 1 - 20 (0x01 - 0x14) UIRD formatted raw data for the Simple AV command number or key being downloaded or uploaded Values in the range 0 to 0 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_1_4 and is of type INTEGER.
The Simple AV command number or key going to be downloaded to the ZXT‐310 Referred to Simple AV command class key ID Values in the range 0 to 0 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_21_2 and is of type INTEGER.
Download status register **The status value 1, 3, 4 will be reset to 0 when ZXT‐310 receive a get command to this parameter ** Values in the range 0 to 4 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_22_1 and is of type INTEGER.
This is a read only parameter.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_SIMPLE_AV_CONTROL_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | Linked to BASIC |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.