| layout | title |
|---|---|
documentation |
TZ36D - ZWave |
{% include base.html %}
This describes the Z-Wave device TZ36D, manufactured by TKB Home with the thing type UID of tkb_tz36d_02_001.
This version of the device is limited to firmware versions above 2.1
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The TZ36D supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The TKB Z-Wave dual wall switch is switching attached loads and is controlled either by the local switching paddle or remotely via the Z-Wave wireless protocol
It is included and controlled in a Z-Wave network by a remote control, a wireless control centre or any other kind of Z-Wave controller including a PC-software.
Press On/Off button three times within 1.5 seconds.
Press On/Off button three times within 1.5 seconds.
The following table summarises the channels available for the TZ36D -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
The following table provides a summary of the 5 configuration parameters available in the TZ36D. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Night light | LED behaviour control. |
| 2 | Memory function | Memory function behaviour control. |
| 3 | Invert switch | Swap top and bottom switch/button. |
| 4 | LED transmission indication | LED transmission indication |
| 5 | Suspend group 4 | Group 4 command sending behaviour control. |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
LED behaviour control. From the manual: The LED on the switch will by default, turn ON when the load attached is turned OFF. To make the LED turn ON when the attached load is turned ON, set the parameter 1 to a value of 1. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Switch off = LED off |
| 1 | Switch off = LED on |
The manufacturer defined default value is 1 (Switch off = LED on).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Memory function behaviour control. From the manual: Default value is 1, when the value is 0, switch memory function not open; when the value is 1, open switch memory function. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Memory function off |
| 1 | Memory function on |
The manufacturer defined default value is 1 (Memory function on).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Swap top and bottom switch/button. To switch top and bottom switch, set this parameter to 1. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal behaviour. |
| 1 | Switch top and buttom button. |
The manufacturer defined default value is 0 (Normal behaviour.).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
LED transmission indication Tranmission indication behaviour control.
This parameter controls the LED behaviour when transmitting data to any of the group members. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Do not flicker. |
| 1 | Flicker for 1 second at the beginning |
| 2 | Flicker entire time when transmitting. |
The manufacturer defined default value is 1 (Flicker for 1 second at the beginning).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Group 4 command sending behaviour control. Disable transmitting commands to Group 4. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Sending commands to Group 4 is enabled. |
| 1 | Do not sen commands to Group 4. |
The manufacturer defined default value is 0 (Sending commands to Group 4 is enabled.).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The TZ36D supports 4 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Use the Left Switch to control a group
Association group 2 supports 5 nodes.
Association group 3 supports 5 nodes.
Association group 4 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
| Command Class | Comment |
|---|
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.