board.c

/* Copyright 2023 Dual Tachyon
 * https://github.com/DualTachyon
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 *     Unless required by applicable law or agreed to in writing, software
 *     distributed under the License is distributed on an "AS IS" BASIS,
 *     WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 *     See the License for the specific language governing permissions and
 *     limitations under the License.
 */

#include <string.h>

#ifdef ENABLE_FMRADIO
#include "app/fm.h"
#endif

#include "board.h"
#include "bsp/dp32g030/gpio.h"
#include "bsp/dp32g030/portcon.h"
#include "bsp/dp32g030/saradc.h"
#include "bsp/dp32g030/syscon.h"




#include "driver/eeprom.h"
#include "driver/gpio.h"
#include "driver/system.h"
#include "driver/st7565.h"


#if defined(ENABLE_OVERLAY)
#include "sram-overlay.h"
#endif

#if defined(ENABLE_OVERLAY)
void BOARD_FLASH_Init(void)
    {
        FLASH_Init(FLASH_READ_MODE_1_CYCLE);
        FLASH_ConfigureTrimValues();
        SYSTEM_ConfigureClocks();

        overlay_FLASH_MainClock       = 48000000;
        overlay_FLASH_ClockMultiplier = 48;

        FLASH_Init(FLASH_READ_MODE_2_CYCLE);
    }
#endif
#define ENABLE_SWD
void BOARD_GPIO_Init(void) {
    GPIOA->DIR |= 0
                  // A7 = UART1 TX default as OUTPUT from bootloader!
                  // A8 = UART1 RX default as INPUT from bootloader!
                  // Key pad + I2C
                  | GPIO_DIR_10_BITS_OUTPUT
                  // Key pad + I2C
                  | GPIO_DIR_11_BITS_OUTPUT
                  // Key pad + Voice chip
                  | GPIO_DIR_12_BITS_OUTPUT
                  // Key pad + Voice chip
                  | GPIO_DIR_13_BITS_OUTPUT;
    GPIOA->DIR &= ~(0
                    // Key pad
                    | GPIO_DIR_3_MASK // INPUT
                    // Key pad
                    | GPIO_DIR_4_MASK // INPUT
                    // Key pad
                    | GPIO_DIR_5_MASK // INPUT
                    // Key pad
                    | GPIO_DIR_6_MASK // INPUT
    );
    GPIOB->DIR |= 0
                  // ST7565
                  | GPIO_DIR_9_BITS_OUTPUT
                  // ST7565 + SWD IO
                  | GPIO_DIR_11_BITS_OUTPUT
                  // B14 = SWD_CLK assumed INPUT by default
                  // BK1080
                  | GPIO_DIR_15_BITS_OUTPUT;
    GPIOC->DIR |= 0
                  // BK4819 SCN
                  | GPIO_DIR_0_BITS_OUTPUT
                  // BK4819 SCL
                  | GPIO_DIR_1_BITS_OUTPUT
                  // BK4819 SDA
                  | GPIO_DIR_2_BITS_OUTPUT
                  // Flash light
                  | GPIO_DIR_3_BITS_OUTPUT
                  // Speaker
                  | GPIO_DIR_4_BITS_OUTPUT;
    GPIOC->DIR &= ~(0
                    // PTT button
                    | GPIO_DIR_5_MASK // INPUT
    );


}

void BOARD_PORTCON_Init(void) {
    // PORT A pin selection

    PORTCON_PORTA_SEL0 &= ~(0
                            // Key pad
                            | PORTCON_PORTA_SEL0_A3_MASK
                            // Key pad
                            | PORTCON_PORTA_SEL0_A4_MASK
                            // Key pad
                            | PORTCON_PORTA_SEL0_A5_MASK
                            // Key pad
                            | PORTCON_PORTA_SEL0_A6_MASK
    );
    PORTCON_PORTA_SEL0 |= 0
                          // Key pad
                          | PORTCON_PORTA_SEL0_A3_BITS_GPIOA3
                          // Key pad
                          | PORTCON_PORTA_SEL0_A4_BITS_GPIOA4
                          // Key pad
                          | PORTCON_PORTA_SEL0_A5_BITS_GPIOA5
                          // Key pad
                          | PORTCON_PORTA_SEL0_A6_BITS_GPIOA6
                          // UART1 TX, wasn't cleared in previous step / relying on default value!
                          | PORTCON_PORTA_SEL0_A7_BITS_UART1_TX;

    PORTCON_PORTA_SEL1 &= ~(0
                            // Key pad + I2C
                            | PORTCON_PORTA_SEL1_A10_MASK
                            // Key pad + I2C
                            | PORTCON_PORTA_SEL1_A11_MASK
                            // Key pad + Voice chip
                            | PORTCON_PORTA_SEL1_A12_MASK
                            // Key pad + Voice chip
                            | PORTCON_PORTA_SEL1_A13_MASK
    );
    PORTCON_PORTA_SEL1 |= 0
                          // UART1 RX, wasn't cleared in previous step / relying on default value!
                          | PORTCON_PORTA_SEL1_A8_BITS_UART1_RX
                          // Battery voltage, wasn't cleared in previous step / relying on default value!
                          | PORTCON_PORTA_SEL1_A9_BITS_SARADC_CH4
                          // Key pad + I2C
                          | PORTCON_PORTA_SEL1_A10_BITS_GPIOA10
                          // Key pad + I2C
                          | PORTCON_PORTA_SEL1_A11_BITS_GPIOA11
                          // Key pad + Voice chip
                          | PORTCON_PORTA_SEL1_A12_BITS_GPIOA12
                          // Key pad + Voice chip
                          | PORTCON_PORTA_SEL1_A13_BITS_GPIOA13;


    // PORT B pin selection

    PORTCON_PORTB_SEL0 &= ~(0
                            // SPI0 SSN
                            | PORTCON_PORTB_SEL0_B7_MASK
    );
    PORTCON_PORTB_SEL0 |= 0
                          // SPI0 SSN
                          | PORTCON_PORTB_SEL0_B7_BITS_SPI0_SSN;

    PORTCON_PORTB_SEL1 &= ~(0
                            // ST7565
                            | PORTCON_PORTB_SEL1_B9_MASK
                            // ST7565 + SWD IO
                            | PORTCON_PORTB_SEL1_B11_MASK
                            // SWD CLK
                            | PORTCON_PORTB_SEL1_B14_MASK

    );
    PORTCON_PORTB_SEL1 |= 0
                          // SPI0 CLK, wasn't cleared in previous step / relying on default value!
                          | PORTCON_PORTB_SEL1_B8_BITS_SPI0_CLK
                          // ST7565
                          | PORTCON_PORTB_SEL1_B9_BITS_GPIOB9
                          // SPI0 MOSI, wasn't cleared in previous step / relying on default value!
                          | PORTCON_PORTB_SEL1_B10_BITS_SPI0_MOSI
                          #if defined(ENABLE_SWD)
                          // SWD IO
		| PORTCON_PORTB_SEL1_B11_BITS_SWDIO
		// SWD CLK
		| PORTCON_PORTB_SEL1_B14_BITS_SWCLK
                          #else
                          // ST7565
                          | PORTCON_PORTB_SEL1_B11_BITS_GPIOB11
#endif
            ;

    // PORT C pin selection

    PORTCON_PORTC_SEL0 &= ~(0

                            // Flash light
                            | PORTCON_PORTC_SEL0_C3_MASK
                            // Speaker
                            | PORTCON_PORTC_SEL0_C4_MASK
                            // PTT button
                            | PORTCON_PORTC_SEL0_C5_MASK
    );

    // PORT A pin configuration

    PORTCON_PORTA_IE |= 0
                        // Keypad
                        | PORTCON_PORTA_IE_A3_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_IE_A4_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_IE_A5_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_IE_A6_BITS_ENABLE
                        // A7 = UART1 TX disabled by default
                        // UART1 RX
                        | PORTCON_PORTA_IE_A8_BITS_ENABLE;
    PORTCON_PORTA_IE &= ~(0
                          // Keypad + I2C
                          | PORTCON_PORTA_IE_A10_MASK
                          // Keypad + I2C
                          | PORTCON_PORTA_IE_A11_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_IE_A12_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_IE_A13_MASK
    );

    PORTCON_PORTA_PU |= 0
                        // Keypad
                        | PORTCON_PORTA_PU_A3_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_PU_A4_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_PU_A5_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_PU_A6_BITS_ENABLE;
    PORTCON_PORTA_PU &= ~(0
                          // Keypad + I2C
                          | PORTCON_PORTA_PU_A10_MASK
                          // Keypad + I2C
                          | PORTCON_PORTA_PU_A11_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_PU_A12_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_PU_A13_MASK
    );

    PORTCON_PORTA_PD &= ~(0
                          // Keypad
                          | PORTCON_PORTA_PD_A3_MASK
                          // Keypad
                          | PORTCON_PORTA_PD_A4_MASK
                          // Keypad
                          | PORTCON_PORTA_PD_A5_MASK
                          // Keypad
                          | PORTCON_PORTA_PD_A6_MASK
                          // Keypad + I2C
                          | PORTCON_PORTA_PD_A10_MASK
                          // Keypad + I2C
                          | PORTCON_PORTA_PD_A11_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_PD_A12_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_PD_A13_MASK
    );

    PORTCON_PORTA_OD |= 0
                        // Keypad
                        | PORTCON_PORTA_OD_A3_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_OD_A4_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_OD_A5_BITS_ENABLE
                        // Keypad
                        | PORTCON_PORTA_OD_A6_BITS_ENABLE;
    PORTCON_PORTA_OD &= ~(0
                          // Keypad + I2C
                          | PORTCON_PORTA_OD_A10_MASK
                          // Keypad + I2C
                          | PORTCON_PORTA_OD_A11_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_OD_A12_MASK
                          // Keypad + Voice chip
                          | PORTCON_PORTA_OD_A13_MASK
    );

    // PORT B pin configuration

    PORTCON_PORTB_IE |= 0
                        | PORTCON_PORTB_IE_B14_BITS_ENABLE;
    PORTCON_PORTB_IE &= ~(0
                          // Back light
                          | PORTCON_PORTB_IE_B6_MASK
                          // UART1
                          | PORTCON_PORTB_IE_B7_MASK
                          | PORTCON_PORTB_IE_B8_MASK
                          // ST7565
                          | PORTCON_PORTB_IE_B9_MASK
                          // SPI0 MOSI
                          | PORTCON_PORTB_IE_B10_MASK
                          #if !defined(ENABLE_SWD)
                          // ST7565
                          | PORTCON_PORTB_IE_B11_MASK
                          #endif

    );

    PORTCON_PORTB_PU &= ~(0
                          // Back light
                          | PORTCON_PORTB_PU_B6_MASK
                          // ST7565
                          | PORTCON_PORTB_PU_B9_MASK
                          // ST7565 + SWD IO
                          | PORTCON_PORTB_PU_B11_MASK
                          // SWD CLK
                          | PORTCON_PORTB_PU_B14_MASK

    );

    PORTCON_PORTB_PD &= ~(0
                          // Back light
                          | PORTCON_PORTB_PD_B6_MASK
                          // ST7565
                          | PORTCON_PORTB_PD_B9_MASK
                          // ST7565 + SWD IO
                          | PORTCON_PORTB_PD_B11_MASK
                          // SWD CLK
                          | PORTCON_PORTB_PD_B14_MASK

    );

    PORTCON_PORTB_OD &= ~(0
                          // Back light
                          | PORTCON_PORTB_OD_B6_MASK
                          // ST7565
                          | PORTCON_PORTB_OD_B9_MASK
                          // ST7565 + SWD IO
                          | PORTCON_PORTB_OD_B11_MASK

    );

    PORTCON_PORTB_OD |= 0
                        // SWD CLK
                        | PORTCON_PORTB_OD_B14_BITS_ENABLE;

    // PORT C pin configuration

    PORTCON_PORTC_IE |= 0
                        // PTT button
                        | PORTCON_PORTC_IE_C5_BITS_ENABLE;
    PORTCON_PORTC_IE &= ~(0

                          // Flash Light
                          | PORTCON_PORTC_IE_C3_MASK
                          // Speaker
                          | PORTCON_PORTC_IE_C4_MASK
    );

    PORTCON_PORTC_PU |= 0
                        // PTT button
                        | PORTCON_PORTC_PU_C5_BITS_ENABLE;
    PORTCON_PORTC_PU &= ~(0

                          // Flash Light
                          | PORTCON_PORTC_PU_C3_MASK
                          // Speaker
                          | PORTCON_PORTC_PU_C4_MASK
    );

    PORTCON_PORTC_PD &= ~(0

                          // Flash Light
                          | PORTCON_PORTC_PD_C3_MASK
                          // Speaker
                          | PORTCON_PORTC_PD_C4_MASK
                          // PTT Button
                          | PORTCON_PORTC_PD_C5_MASK
    );

    PORTCON_PORTC_OD &= ~(0

                          // Flash Light
                          | PORTCON_PORTC_OD_C3_MASK
                          // Speaker
                          | PORTCON_PORTC_OD_C4_MASK
    );
    PORTCON_PORTC_OD |= 0

                        // Flash Light
                        | PORTCON_PORTC_OD_C3_BITS_DISABLE
                        // Speaker
                        | PORTCON_PORTC_OD_C4_BITS_DISABLE
                        // PTT button
                        | PORTCON_PORTC_OD_C5_BITS_ENABLE;
}

void BOARD_Init(void) {
    BOARD_PORTCON_Init();
    BOARD_GPIO_Init();
    ST7565_Init();
//    BOARD_FLASH_Init();



}