Boot failed while testing on Raspi4B

[InfluencerNGZK]

使用v0.3.4版本在树莓派4B测试出现如下BUG，使用v0.4版本卡在Starting kernel处，请问应该如何debug

U-Boot 2022.07

DRAM:  3.9 GiB
RPI 4 Model B (0xc03115)
Core:  209 devices, 15 uclasses, devicetree: board
MMC:   mmcnr@7e300000: 1, mmc@7e340000: 0
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: Register 5000420 NbrPorts 5
Starting the controller
USB XHCI 1.00
scanning bus xhci_pci for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
U-Boot> fatload mmc 0:1 0x37200000 zephyr.bin
139416 bytes read in 29 ms (4.6 MiB/s)
U-Boot> fatload mmc 0:1 0x30008000 Image
13511168 bytes read in 609 ms (21.2 MiB/s)
U-Boot> fatload mmc 0:1 0x33e00000 vm1_dtb.img
2630 bytes read in 24 ms (106.4 KiB/s)
U-Boot> fatload mmc 0:1 0x34000000 vm1_ramdisk.img
5622142 bytes read in 270 ms (19.9 MiB/s)
U-Boot> fatload mmc 0:1 0x37408000 minos.bin
326131 bytes read in 29 ms (10.7 MiB/s)
U-Boot> fatload mmc  0:1 0x38000000 minos.dtb
12281 bytes read in 30 ms (399.4 KiB/s)
U-Boot> fatload mmc 0:1 0x00080000 Image
13511168 bytes read in 609 ms (21.2 MiB/s)
U-Boot> fatload mmc 0:1 0x03e00000 vm0_dtb.img
41128 bytes read in 25 ms (1.6 MiB/s)
U-Boot> booti 0x37408000 - 0x38000000
## Flattened Device Tree blob at 38000000
   Booting using the fdt blob at 0x38000000
   Using Device Tree in place at 0000000038000000, end 0000000038005ff8

Starting kernel ...

[       0.000000@00 999] NIC Starting Minos v0.3.2-rc1 unstable
[       0.000000@00 999] NIC bootmem start-0x00000000374579f8 end-0x0000000037460000 size-0x8608
[       0.000000@00 999] NIC current EL is 0x2
[       0.000000@00 999] NIC ID_ISAR5_EL1: 0x10001
[       0.000000@00 999] NIC using device tree @0x38000000
[       0.000000@00 999] NIC model : Raspberry Pi 4 Model B
[       0.000000@00 999] NIC platform : raspberrypi,4-model-b
[       0.000000@00 999] NIC memory node address_cells:2 size_cells:1
[       0.000000@00 999] NIC DTB - 0x38000000 ---> 0x4000
[       0.000000@00 999] NIC MEM: 0x0000000000000000 ---> 0x0000000037400000 [0x0000000037400000] VM
[       0.000000@00 999] NIC MEM: 0x00000000bc000000 ---> 0x00000000fc000000 [0x0000000040000000] Normal
[       0.000000@00 999] NIC MEM: 0x0000000037400000 ---> 0x0000000038000000 [0x0000000000c00000] Kernel
[       0.000000@00 999] NIC MEM: 0x0000000038004000 ---> 0x000000003b400000 [0x00000000033fc000] Kernel
[       0.000000@00 999] NIC MEM: 0x0000000038000000 ---> 0x0000000038004000 [0x0000000000004000] DTB
[       0.000000@00 999] NIC MEM: 0x0000000040000000 ---> 0x00000000bc000000 [0x000000007c000000] VM
[       0.000000@00 999] NIC dynamic memory allocator init..
[       0.000000@00 999] NIC slab memory allocator init...
[       0.000000@00 999] NIC BLOCK SECTION: 0x00000000bc000000 ---> 0x00000000fc000000 [0x0000000040000000]
[       0.000000@00 999] NIC BLOCK SECTION: 0x0000000037400000 ---> 0x0000000038000000 [0x0000000000c00000]
[       0.000000@00 999] NIC BLOCK SECTION: 0x0000000038200000 ---> 0x000000003b5fc000 [0x00000000033fc000]
[       0.000000@00 999] NIC PAGE  SECTION: 0x0000000038004000 ---> 0x0000000038200000 [0x1fc000]
[       0.000000@00 999] NIC code_start:0x37400000 code_end:0x37460000
[       0.000000@00 999] NIC code_start after blocks_init:0x37465528
[       0.000000@00 999] NIC minos : free_memory_start:0x37600000
[       0.000000@00 999] NIC add left bootmem to slab 0x0000000037459b10->0x64f0
[       0.000000@00 999] ERR ramdisk address is not set
[       0.000000@00 999] NIC parsing SMC/HVC handler
[       0.000000@00 999] NIC *** gicv2 init ***
[       0.000000@00 999] NIC gicv2 information: gic_dist_addr=00000000ff841000 size=0x1000 gic_cpu_addr=00000000ff842000 size=0x2000 gic_hyp_addr=00000000ff844000 size=0x2000 gic_vcpu_addr=00000000ff846000 size=0x2000
[       0.000000@00 999] WRN PMD block remap 0xff800000 ---> 0xff800000 @0x200000
[       0.000000@00 999] WRN PMD block remap 0xff800000 ---> 0xff800000 @0x200000
[       0.000000@00 999] NIC GICv2: 256 lines, 4 cpus, secure (IID 200143b).
[       0.000000@00 999] NIC vgicv2 vtr 0x90000003 nr_lrs : 0x4
[       0.000000@00 999] NIC cpu@0 using spin-table relase addr 0x00000000000000d8
[       0.000000@00 999] NIC cpu@1 using spin-table relase addr 0x00000000000000e0
[       0.000000@00 999] NIC cpu@2 using spin-table relase addr 0x00000000000000e8
[       0.000000@00 999] NIC cpu@3 using spin-table relase addr 0x00000000000000f0
[       0.000000@00 999] WRN not support unmask irq_percpu
[       0.000000@00 999] WRN not support unmask irq_percpu
[       0.000000@00 999] WRN not support unmask irq_percpu
[       0.000000@00 999] WRN not support unmask irq_percpu
[       0.000000@00 999] NIC    sec_phy_timer  : 29
[       0.000000@00 999] NIC nonsec_phy_timer  : 30
[       0.000000@00 999] NIC       virt_timer  : 27
[       0.000000@00 999] NIC hypervisor_timer  : 26
[      85.608033@00 999] NIC get timer clock freq from reg 54000
[       0.000000@00 999] NIC boot ticks is :0x1138faf79
[       0.005249@00 999] WRN PMD block remap 0x0 ---> 0x0 @0x200000
[       0.011240@00 999] WRN destroy host mapping 0xe0---->0xe8
[       0.014586@01 999] NIC cpu-1 is up
[       0.017051@00 999] NIC waiting 2 seconds for cpu-1 up
[       0.026259@00 999] WRN destroy host mapping 0xe8---->0xf0
[       0.029597@02 999] NIC cpu-2 is up
[       0.032064@00 999] NIC waiting 2 seconds for cpu-2 up
[       0.041273@00 999] WRN destroy host mapping 0xf0---->0xf8
[       0.044637@03 999] NIC cpu-3 is up
[       0.047079@00 999] NIC waiting 2 seconds for cpu-3 up
[       0.056390@00 999] ERR can not get load-address
[       0.061297@00 999] NIC **** create new vm ****
[       0.066028@00 999] NIC     vmid: 0
[       0.069804@00 999] NIC     name: rpi4_linux_host
[       0.074809@00 999] NIC     os_type: linux
[       0.079199@00 999] NIC     nr_vcpu: 2
[       0.083238@00 999] NIC     entry: 0x0000000000080000
[       0.088594@00 999] NIC     setup_data: 0x0000000003e00000
[       0.094389@00 999] NIC     load-address: 0x0000000000000000
[       0.100360@00 999] NIC     image-file:
[       0.104574@00 999] NIC     dtb-file:
[       0.108613@00 999] NIC     64-bit vm
[       0.112564@00 999] NIC     flags: 0x1
[       0.116603@00 999] NIC     affinity: 0 1 0 0 0 0 0 0
[       0.139547@00 999] WRN virq-chip :brcm,bcm2711-gpio not found
[       0.144929@00 999] NIC create vgicv2 for vm-0
[       0.157777@00 999] NIC vgicv2 address 0xff841000 0x1000 0xff842000 0x2000
[       0.164191@00 999] NIC map gicc 0xff842000 to gicv 0xff846000 size 0x2000
[       0.678663@00 999] ERR invalid vmm_area config 0x00000000fe300000 0x100
[       0.709229@00 999] ERR invalid vmm_area config 0x00000000fe600000 0x100
[       0.756501@00 999] ERR invalid vmm_area config 0x00000000fe200000 0x1000
[       0.878281@00 999] ERR memory region:0x0000000000000e14 not register
[       0.892225@00 999] WRN bad address index 0 for genet-phy@0
[       1.037117@00 999] NIC New cmdline: coherent_pool=1M 8250.nr_uarts=1 earlycon=uart8250,mmio32,0xfe215040 loglevel=9 cma=64M cma=256M video=HDMI-A-1:720x576M@50,margin_left=0,margin_right=0,margin_top=0,margin_bottom=0 smsc95xx.macaddr=DC:A6:32:1C:65:A1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.fiq_fix_enable=0 console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait rootflags=noload net.ifnames=0 loglevel=9
[       1.081575@00 999] NIC delete vcpu cpu@2 for vm0
[       1.085822@00 999] NIC delete vcpu cpu@3 for vm0
[       1.101420@00 999] NIC fdt_setup_memory size-cells:1 address-cells:2
[       1.107393@00 999] NIC add memory region to vm0 0x0000000000000000 0x0000000037400000
[       1.115646@00 999] NIC add memory region to vm0 0x0000000040000000 0x000000007c000000
[       1.131716@00 999] NIC vcpu-0 release addr redirect to 0x00000000ff800000
[       1.138157@00 999] NIC vcpu-1 release addr redirect to 0x00000000ff800008
[       1.145348@00 999] NIC raspberry4 setup vm done
[       1.150553@00 999] NIC vm-0 vcpu-0 affnity to pcpu-0
[       1.155604@00 999] NIC vmpidr is 0x0
[       1.159555@00 999] NIC vm-0 vcpu-1 affnity to pcpu-1
[       1.164910@00 999] NIC vmpidr is 0x1                                                                                                                  0
[ mino  1.169579@00 074] NIC release task pid: 73 name: init
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[    0.000000] Linux version 4.19.76-v8 (pi@raspberrypi) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Tue Nov 8 10:59:42 CST 2022
[    0.000000] Machine model: Raspberry Pi 4 Model B
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000fe215040 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 256 MiB at 0x0000000027400000
[    0.000000] On node 0 totalpages: 734208
[    0.000000]   DMA32 zone: 3536 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 226304 pages, LIFO batch:63
[    0.000000]   Normal zone: 7936 pages used for memmap
[    0.000000]   Normal zone: 507904 pages, LIFO batch:63
[    0.000000] random: get_random_bytes called from start_kernel+0xb0/0x47c with crng_init=0
[    0.000000] percpu: Embedded 24 pages/cpu s57432 r8192 d32680 u98304
[    0.000000] pcpu-alloc: s57432 r8192 d32680 u98304 alloc=24*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for EL2 vector hardening
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 722736
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 earlycon=uart8250,mmio32,0xfe215040 loglevel=9 cma=64M cma=256M video=HDMI-A-1:720x576M@50,margin_left=0,margin_right=0,margin_top=0,margin_bottom=0 smsc95xx.macaddr=DC:A6:32:1C:65:A1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.fiq_fix_enable=0 console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait rootflags=noload net.ifnames=0 loglevel=9
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB: mapped [mem 0x233ff000-0x273ff000] (64MB)
[    0.000000] Memory: 2538368K/2936832K available (8572K kernel code, 1034K rwdata, 2592K rodata, 960K init, 1109K bss, 136320K reserved, 262144K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] ftrace: allocating 28329 entries in 111 pages
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000006] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.008331] Console: colour dummy device 80x25
[    0.013233] console [tty1] enabled
[    0.016685] vmbox hvc console init for backend
[    0.021280] can not find the hvc console device
[    0.025907] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[    0.036495] pid_max: default: 32768 minimum: 301
[    0.041435] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.048276] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[       1.745767@00 071] NIC vcpu-1 of vm-0 power on from vm suspend 0x00000000008d31a8
[    0.064904] ASID allocator initialised with 32768 entries
[    0.070677] rcu: Hierarchical SRCU implementation.
[    0.076588] EFI services will not be available.
[    0.081543] smp: Bringing up secondary CPUs ...
[    0.087359] Detected PIPT I-cache on CPU1
[    0.087454] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[    0.087651] smp: Brought up 1 node, 2 CPUs
[    0.102494] SMP: Total of 2 processors activated.
[    0.107274] CPU features: detected: 32-bit EL0 Support
[    0.113214] CPU: All CPU(s) started at EL1
[    0.117412] alternatives: patching kernel code
[    0.123191] devtmpfs: initialized
[    0.134148] Enabled cp15_barrier support
[    0.138217] Enabled setend support
[    0.142038] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.151930] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.164813] pinctrl core: initialized pinctrl subsystem
[    0.170787] DMI not present or invalid.
[    0.174699] register vmbox bus
[    0.178182] NET: Registered protocol family 16
[    0.183836] cpuidle: using governor menu
[    0.188052] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[    0.195564] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.204850] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.211210] Serial: AMBA PL011 UART driver
[    0.215448] find irq domain gic400@40041000
[    0.253316] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.290188] bcm2835-dma fe007000.dma: DMA legacy API manager at (____ptrval____), dmachans=0x1
[    0.301202] vgaarb: loaded
[    0.304248] SCSI subsystem initialized
[    0.308251] usbcore: registered new interface driver usbfs
[    0.313869] usbcore: registered new interface driver hub
[    0.319347] usbcore: registered new device driver usb
[    0.324566] pps_core: LinuxPPS API ver. 1 registered
[    0.329610] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.338883] PTP clock support registered
[    0.343342] raspberrypi-firmware soc:firmware: Attached to firmware from 2022-08-26 14:03, variant start
[    0.353059] raspberrypi-firmware soc:firmware: Firmware hash is 102f1e848393c2112206fadffaaf86db04e98326
[    0.363991] clocksource: Switched to clocksource arch_sys_counter
[    0.447243] VFS: Disk quotas dquot_6.6.0
[    0.451326] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.458475] FS-Cache: Loaded
[    0.461630] CacheFiles: Loaded
[    0.465273] simple-framebuffer chosen:framebuffer@0x3eb30000: No memory resource
[    0.472800] simple-framebuffer: probe of chosen:framebuffer@0x3eb30000 failed with error -22
[    0.492780] NET: Registered protocol family 2
[    0.497871] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[    0.505890] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.513417] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.520582] TCP: Hash tables configured (established 32768 bind 32768)
[    0.527419] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.533591] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.540372] NET: Registered protocol family 1
[    0.553622] RPC: Registered named UNIX socket transport module.
[    0.559688] RPC: Registered udp transport module.
[    0.564469] RPC: Registered tcp transport module.
[    0.569245] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.575786] PCI: CLS 0 bytes, default 64
[    0.580913] hw perfevents: failed to parse interrupt-affinity[2] for arm-pmu
[    0.588088] hw perfevents: /arm-pmu: failed to register PMU devices!
[    0.594576] armv8-pmu: probe of arm-pmu failed with error -22
[    0.605179] Initialise system trusted keyrings
[    0.609986] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.623696] FS-Cache: Netfs 'nfs' registered for caching
[    0.633834] NFS: Registering the id_resolver key type
[    0.639006] Key type id_resolver registered
[    0.643259] Key type id_legacy registered
[    0.647344] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.657197] Key type asymmetric registered
[    0.661384] Asymmetric key parser 'x509' registered
[    0.666411] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.674093] io scheduler noop registered
[    0.678103] io scheduler deadline registered
[    0.682587] io scheduler cfq registered (default)
[    0.687388] io scheduler mq-deadline registered
[    0.691997] io scheduler kyber registered
[    0.699153] brcm-pcie fd500000.pcie: could not get clock
[    0.704627] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    0.711750] brcm-pcie fd500000.pcie:   MEM 0x600000000..0x603ffffff -> 0xf8000000
[    0.792034] brcm-pcie fd500000.pcie: link up, 5.0 Gbps x1 (!SSC)
[    0.798411] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    0.804805] pci_bus 0000:00: root bus resource [bus 00-01]
[    0.810392] pci_bus 0000:00: root bus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff])
[    0.820941] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    0.827201] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.835638] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    0.841871] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    0.849078] pci 0000:01:00.0: PME# supported from D0 D3hot
[    0.857343] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    0.864428] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    0.872085] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.877138] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    0.884286] pci 0000:00:00.0: enabling device (0000 -> 0002)
[    0.890076] pci 0000:01:00.0: enabling device (0000 -> 0002)
[   21.446910] pci 0000:01:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x811
[   21.454831] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x8e0 took 20088442 usecs
[   21.462957] bcm2708_fb soc:fb: Unable to determine number of FB's. Assuming 1
[   21.470206] bcm2708_fb soc:fb: FB found 1 display(s)
[   21.475538] raspberrypi-firmware soc:firmware: Request 0x00048003 returned status 0x80000001
[   21.484105] bcm2708_fb soc:fb: Failed to allocate GPU framebuffer (-22)
[   21.490847] bcm2708_fb soc:fb: probe failed, err -22
[   21.495907] bcm2708_fb: probe of soc:fb failed with error -22
[   21.503359] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[   21.511796] iproc-rng200 fe104000.rng: hwrng registered
[   21.517407] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[   21.526551] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[   21.534472] cacheinfo: Unable to detect cache hierarchy for CPU 0
[   21.550085] brd: module loaded
[   21.562132] loop: module loaded
[   21.566175] Loading iSCSI transport class v2.0-870.
[   21.573074] libphy: Fixed MDIO Bus: probed
[   21.577734] bcmgenet fd580000.genet: failed to get enet clock
[   21.583582] bcmgenet fd580000.genet: GENET 5.0 EPHY: 0x0000
[   21.589247] bcmgenet fd580000.genet: failed to get enet-wol clock
[   21.595436] bcmgenet fd580000.genet: failed to get enet-eee clock
[   21.601636] bcmgenet: Skipping UMAC reset
[   21.605936] unimac-mdio unimac-mdio.-19: DMA mask not set
[   21.620031] libphy: bcmgenet MII bus: probed
[   21.648814] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus at 0x(____ptrval____)
[   21.657861] usbcore: registered new interface driver r8152
[   21.663512] usbcore: registered new interface driver lan78xx
[   21.669312] usbcore: registered new interface driver smsc95xx
[   21.675497] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   21.680850] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[   22.188441] xhci_hcd 0000:01:00.0: can't setup: -110
[   22.193492] xhci_hcd 0000:01:00.0: USB bus 1 deregistered
[   22.199025] xhci_hcd 0000:01:00.0: init 0000:01:00.0 fail, -110
[   22.205070] xhci_hcd: probe of 0000:01:00.0 failed with error -110
[   22.211721] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[   22.217870] dwc_otg fe980000.usb: base=(____ptrval____)
[   22.425527] Core Release: 2.80a
[   22.428735] Setting default values for core params
[   22.433619] Finished setting default values for core params
[   22.641789] Using Buffer DMA mode
[   22.645165] Periodic Transfer Interrupt Enhancement - disabled
[   22.651083] Multiprocessor Interrupt Enhancement - disabled
[   22.656740] OTG VER PARAM: 0, OTG VER FLAG: 0
[   22.661168] Dedicated Tx FIFOs mode
[   22.665136] WARN::dwc_otg_hcd_init:1043: FIQ DMA bounce buffers: virt = ffffff8008fd9000 dma = 0x00000000e7504000 len=9024
[   22.676373] FIQ FSM acceleration enabled for :
[   22.676373] Non-periodic Split Transactions
[   22.676373] Periodic Split Transactions
[   22.676373] High-Speed Isochronous Endpoints
[   22.676373] Interrupt/Control Split Transaction hack enabled
[   22.699006] dwc_otg: Microframe scheduler enabled
[   22.703857] WARN::hcd_init_fiq:496: MPHI regs_base at ffffff8008e85200
[   22.710569] dwc_otg fe980000.usb: DWC OTG Controller
[   22.715639] dwc_otg fe980000.usb: new USB bus registered, assigned bus number 1
[   22.723084] dwc_otg fe980000.usb: irq 357, io mem 0x00000000
[   22.728872] Init: Port Power? op_state=1
[   22.732859] Init: Power Port (0)
[   22.736401] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[   22.744792] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   22.752128] usb usb1: Product: DWC OTG Controller
[   22.756909] usb usb1: Manufacturer: Linux 4.19.76-v8 dwc_otg_hcd
[   22.763007] usb usb1: SerialNumber: fe980000.usb
[   22.768256] hub 1-0:1.0: USB hub found
[   22.772125] hub 1-0:1.0: 1 port detected
[   22.776717] dwc_otg: FIQ enabled
[   22.780023] dwc_otg: NAK holdoff enabled
[   22.784016] dwc_otg: FIQ split-transaction FSM enabled
[   22.789246] Module dwc_common_port init
[   22.793401] usbcore: registered new interface driver uas
[   22.798866] usbcore: registered new interface driver usb-storage
[   22.805143] mousedev: PS/2 mouse device common for all mice
[   22.812095] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[   22.818764] bcm2835-cpufreq: min=600000 max=1500000
[   22.824342] sdhci: Secure Digital Host Controller Interface driver
[   22.830626] sdhci: Copyright(c) Pierre Ossman
[   22.835465] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe
[   22.842838] sdhci-pltfm: SDHCI platform and OF driver helper
[   22.851541] ledtrig-cpu: registered to indicate activity on CPUs
[   22.857791] hidraw: raw HID events driver (C) Jiri Kosina
[   22.863430] usbcore: registered new interface driver usbhid
[   22.869093] usbhid: USB HID core driver
[   22.873757] vchiq: vchiq_init_state: slot_zero = (____ptrval____), is_master = 0
[   22.883885] Minos Hyperviosr Driver Init ...
[   22.888426] Minos Hyperviosr Driver Init Done
[   22.893141] register vmbox controller driver
[   22.898050] register vmbox driver: vmbox-console...
[   22.903064] register vmbox driver: vmbox-veth...
[   22.908064] Initializing XFRM netlink socket
[   22.912436] NET: Registered protocol family 17
[   22.917041] Key type dns_resolver registered
[   22.922064] registered taskstats version 1
[   22.926245] Loading compiled-in X.509 certificates
[   22.938217] uart-pl011 fe201000.serial: cts_event_workaround enabled
[   22.944781] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 353, base_baud = 0) is a PL011 rev2
[   22.957145] console [ttyS0] disabled
[   22.960838] fe215040.serial: ttyS0 at MMIO 0x0 (irq = 355, base_baud = 62500000) is a 16550
[   22.969348] console [ttyS0] enabled
[   22.969348] console [ttyS0] enabled
[   22.976458] bootconsole [uart8250] disabled
[   22.976458] bootconsole [uart8250] disabled
[   22.985410] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[   22.993357] brcmstb_thermal fd5d2200.thermal: registered AVS TMON of-sensor driver
[   23.001726] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[   23.007859] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[   23.039853] sdhci-iproc fe340000.emmc2: Linked as a consumer to regulator.1
[   23.062908] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[   23.070181] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[   23.077448] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[   23.083074] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA
[   23.093504] of_cfs_init
[   23.096072] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[   23.096179] of_cfs_init: OK
[   23.105895] Waiting for root device /dev/mmcblk0p2...
[   23.105945] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[   23.160066] mmc0: invalid bus width
[   23.163624] mmc0: error -22 whilst initialising SD card
[   23.183120] random: fast init done
[   23.204790] mmc1: new high speed SDIO card at address 0001
[   23.242681] mmc0: invalid bus width
[   23.246263] mmc0: error -22 whilst initialising SD card
[   23.325288] mmc0: invalid bus width
[   23.328869] mmc0: error -22 whilst initialising SD card
[   23.424177] mmc0: invalid bus width
[   23.427732] mmc0: error -22 whilst initialising SD card
[   24.523682] mmc0: invalid bus width
[   24.527261] mmc0: error -22 whilst initialising SD card
[   24.598016] mmc0: invalid bus width
[   24.601597] mmc0: error -22 whilst initialising SD card
[   24.680566] mmc0: invalid bus width
[   24.684144] mmc0: error -22 whilst initialising SD card
[   24.779531] mmc0: invalid bus width
[   24.783110] mmc0: error -22 whilst initialising SD card
[   25.867562] mmc0: invalid bus width
[   25.871139] mmc0: error -22 whilst initialising SD card
[   25.941887] mmc0: invalid bus width
[   25.945469] mmc0: error -22 whilst initialising SD card
[   26.024453] mmc0: invalid bus width
[   26.028032] mmc0: error -22 whilst initialising SD card
[   26.123331] mmc0: invalid bus width
[   26.126909] mmc0: error -22 whilst initialising SD card
[   27.208795] mmc0: invalid bus width
[   27.212372] mmc0: error -22 whilst initialising SD card
[   27.283141] mmc0: invalid bus width
[   27.286721] mmc0: error -22 whilst initialising SD card
[   27.365768] mmc0: invalid bus width
[   27.369346] mmc0: error -22 whilst initialising SD card
[   27.464705] mmc0: invalid bus width
[   27.468283] mmc0: error -22 whilst initialising SD card
[   28.555548] mmc0: invalid bus width

[lemin9538]

从log看 应该是emmc controller的dts可能有问题，你的vm0 dts image是怎么生成的？

V0.4我没有在rpi4上测试过，需要自己移植下。

[InfluencerNGZK]

参考v0.3.4版本的文档
vm0.dtb从minos-misc目录获取
dts文件是dtbs文件夹下自带的
Image是rpi4分支下的Linux编译生成的

没太理解您说dts有问题具体指什么？

[wusnga8dn]

参考v0.3.4版本的文档 vm0.dtb从minos-misc目录获取 dts文件是dtbs文件夹下自带的 Image是rpi4分支下的Linux编译生成的

没太理解您说dts有问题具体指什么？
你好我想请问一下，你将这个项目正常运行起来了吗，用的什么版本的树莓派系统？