Redmi AX5 #1
Comments
|
I have an ax5 that has been upgraded to 1G memory. If you need to test it, please contact me. |
|
At present, the firmware I flashed after successfully compiling can boot normally. If add luci, there will be problems. |
You can try the firmware of Xiaomi AX1800 for flashing, it should be able to boot directly.
What's the problem? |
|
Can't start and the LED keeps flashing. |
Can you provide boot log? |
|
I made a new firmware and will see if it can boot later，if possible, I hope we can communicate in Chinese, because my English is not very good, thank you.😀 |
|
可以 |
|
我编译了个新的，晚点刷上去看看，要不启动的话再输出下ttl给你看看 |
|
你可以试试这里的固件，它包含luci，可以正常启动 |
好的谢谢，我晚上试试 |
|
|
|
你说它每次重启不会自己启动这个问题，我似乎没有遇到，是不是已经修复了？ |
没有修复，目前只有小米AX1800发现有这个问题 |
|
好吧，ax5一切正常，我改天搬个ax5选项出来，这样好看些，虽然ax1800和ax5都一样😂 |
两个型号的BDF有些区别的，你可以用这个issue里最开始提到的文件试试 |
|
好的谢谢，我有空再试试 |
|
你有测试过这个nss有起效吗 |
|
没，有测试的具体步骤吗？ |
|
好像是跑iperf3看cpu占有率，最准确是用wifi跑，但这个固件没有wifi |
|
固件是支持WiFi的，之前测过WiFi下载跑到900Mbps以上，CPU占用大概30% |
|
你发的那份刷完没有无线的选项，但软件包里能看到驱动也是奇怪 |
|
日志有什么报错吗？ |
|
好像没有 |
|
可以看看你的无线界面吗 |
My all ipq60xx devices has been upgraded to 1GB. 😅 EDIT: |
|
https://pastebin.com/raw/HTrZbvRv still should be fine. You will have more memory for Linux itself |
I wish more memory is used for wifi, because this firmware is used as an AP for me. |
We can make another subtarget which uses modified dtsi |
|
I think this is a bit too much trouble. 😂It’s better to upgrade the memory to 1G. BTW, I hope that the discussion related to this topic can be moved to this issue https://github.com/openwrt-dev/ci-ipq60xx/issues/3, so close this. |
pexcn
pushed a commit
that referenced
this issue
Jan 10, 2024
Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 16MB NOR RAM: 256MB Ethernet: 2x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset Power: DC 12V 1A, PoE 802.3af 48V Flash instructions: Option #1 - SSH I was able to SSH into the stock firmware of my device. 1. Attach the router to the network 2. Use scp (-O) to copy the sysupgrade image 3. Connect using SSH and run `sysupgrade -n` Option #2 - U-Boot One way to use the bootloader for flashing is using TFTP: 1. Connect to the router using an ethernet cable 2 Spin up a TFTP server serving the sysupgrade file 3. Open the case and attach a UART 4. Attach power to the router and interrupt the countdown by pressing any key 5. Select option #2 (Upgrade firmware) 6. Enter IP address information and image name 7. Wait patiently Co-Authored-By: Enrique Rodríguez Valencia <[email protected]> Co-Authored-By: Hauke Mehrtens <[email protected]> Signed-off-by: Leon M. Busch-George <[email protected]>
|
Reopen it, need test ax5-cn-and-intl-bdwlan.zip... |
pexcn
pushed a commit
that referenced
this issue
Mar 21, 2024
Currently, the existing uncompressed kallsym support is causing qualcommax boards to hang on boot, and only after earlycon and verbose BUG() prints are enabled the trace is visible: [ 0.000000] ------------[ cut here ]------------ [ 0.000000] kernel BUG at kernel/kallsyms.c:340! [ 0.000000] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP Felix has fixed up the uncompressed kallsyms support so modify the current patch with the fix. All credits for the code go to Felix. Signed-off-by: Robert Marko <[email protected]>
pexcn
pushed a commit
that referenced
this issue
May 22, 2024
Don't add KERNEL_TESTING_PATCHVER yet as there are some issues with it. On TP-Link Archer C2300 serial console seems to stop working after preinit: > Press the [f] key and hit [enter] to enter failsafe mode > Press the [1], [2], [3] or [4] key and hit [enter] to select the de� On Netgear R8000P XHCI causes external abort: [ 2.139586] Internal error: synchronous external abort: 0000000096000210 [#1] SMP [ 2.147212] Modules linked in: xhci_plat_hcd(+) xhci_hcd ohci_platform ohci_hcd fsl_mph_dr_of ehci_platform ehci_fsl ehci_hcd gpio_button_hotplug(O) usbcore nls_base usb_common crc32c_generic [ 2.164774] CPU: 0 PID: 358 Comm: kmodloader Tainted: G O 6.6.22 #0 [ 2.172658] Hardware name: Netgear R8000P (DT) [ 2.177229] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 2.184395] pc : xhci_gen_setup+0x80/0x34c [xhci_hcd] [ 2.189591] lr : xhci_gen_setup+0x74/0x34c [xhci_hcd] [ 2.194788] sp : ffffffc0815d37b0 [ 2.198194] x29: ffffffc0815d37b0 x28: ffffff8002000000 x27: ffffff8001172d88 [ 2.205540] x26: ffffff8002000000 x25: 0000000000000000 x24: ffffffc078b603c0 [ 2.212888] x23: ffffffc078b2a008 x22: ffffff8001172c10 x21: ffffff8002000000 [ 2.220235] x20: ffffff8002000000 x19: ffffff8002000250 x18: 0000000000000000 [ 2.227582] x17: 626d756e20737562 x16: 2064656e67697373 x15: ffffffffffffffff [ 2.234929] x14: ffffff80019e9915 x13: ffffff80019e9913 x12: 00000000ffffffea [ 2.242276] x11: 00000000ffffefff x10: 0000000000000062 x9 : 00000000ffffffd0 [ 2.246760] bcm63138_nand ff801800.nand-controller: timeout waiting for command 0x4 [ 2.249623] x8 : 0000000000000073 x7 : ffffffc0815d37c0 x6 : 0000000000000075 [ 2.257513] bcm63138_nand ff801800.nand-controller: intfc status c00000e0 [ 2.264855] x5 : 0000000000000081 x4 : 0000000000000000 x3 : ffffff8001b61800 [ 2.279193] x2 : ffffffc080b5d000 x1 : ffffff80020003a8 x0 : ffffff8002000398 [ 2.286540] Call trace: [ 2.289048] xhci_gen_setup+0x80/0x34c [xhci_hcd] Signed-off-by: Rafał Miłecki <[email protected]>
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 18, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 18, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 5, 2024
If this function is marked as __init, kernel will splat when driver is (re)bind echo "c080000.ethernet">/sys/bus/platform/drivers/ipqess-edma/unbind echo "c080000.ethernet">/sys/bus/platform/drivers/ipqess-edma/bind Example with additional print messages, functions at boot: [ 2.039468] ipqess-edma c080000.ethernet: ipqess_axi_probe pre register_netdev [ 2.039530] ipqess-edma c080000.ethernet: *netdev: c27d2000 [ 2.045609] ipqess-edma c080000.ethernet: &ipqess_init: c0d1e28c [ 2.051122] ipqess_init [ 2.057338] netdev: c27d2000 [ 2.059492] ess = netdev_priv: c27d2500 [ 2.062615] ess->pdev: c2138c00 [ 2.066174] ess->pdev->dev: c2138c10 [ 2.069314] ess->pdev->dev.of_node: ef6f6368 [ 2.073120] ess->pdev->dev.of_node: /soc/ethernet@c080000 fails (bind) after unbind: [ 34.987948] ipqess-edma c080000.ethernet: ipqess_axi_probe pre register_netdev [ 34.988012] ipqess-edma c080000.ethernet: *netdev: c27d6000 [ 34.994088] ipqess-edma c080000.ethernet: &ipqess_init: c0d1e28c [ 34.999652] 8<--- cut here --- [ 35.005802] Unable to handle kernel paging request at virtual address c0d1e28c when execute [ 35.008676] [c0d1e28c] *pgd=80c1941e(bad) [ 35.016918] Internal error: Oops: 8000000d [#1] SMP ARM Signed-off-by: John Thomson <[email protected]> Link: openwrt#15831 Signed-off-by: Robert Marko <[email protected]>
pexcn
pushed a commit
that referenced
this issue
Jul 5, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 10, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 10, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 12, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 12, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 20, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 20, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 24, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 24, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
I have a Redmi AX5, but I haven't upgraded the RAM, maybe support for it will be added in the future, maybe not. So backup some necessary information here.
ax5_stock_firmware_boot.log
ax5-bdf.zip
UPDATE ON 20240105
ax5-cn-and-intl-bdwlan.zip
The text was updated successfully, but these errors were encountered: