-
Notifications
You must be signed in to change notification settings - Fork 1
/
Copy pathMakefile
125 lines (104 loc) · 4.53 KB
/
Makefile
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
# Name: Makefike
# Author: Patrik Axelsson
# Copyright: Copyright 2016 Patrik Axelsson, David Eriksson
# License: AmigaKeyboard2C64 is licensed under GNU General Public License, version 2
# This is a prototype Makefile. Modify it according to your needs.
# You should at least check the settings for
# DEVICE ....... The AVR device you compile for
# CLOCK ........ Target AVR clock rate in Hertz
# OBJECTS ...... The object files created from your source files. This list is
# usually the same as the list of source files with suffix ".o".
# PROGRAMMER ... Options to avrdude which define the hardware you use for
# uploading to the AVR and the interface where this hardware
# is connected.
# FUSES ........ Parameters for avrdude to flash the fuses appropriately.
#DEVICE = atmega324p
DEVICE = atmega88
CLOCK = 13500000
#CLOCK = 16000000
PROGRAMMER = -c stk500v2 -P /dev/tty.usbserial-FTTBQ2KPB
TINYPROGRAMMER = -c usbtiny
OBJECTS = main.o amiga_keyb_if.o c64_keyb_sim.o uart.o
FUSES = -U hfuse:w:0xdf:m -U lfuse:w:0xc2:m
#FUSES = -U hfuse:w:0xd9:m -U lfuse:w:0xc2:m
#FUSES = -U hfuse:w:0xd9:m -U lfuse:w:0xc0:m
# http://www.engbedded.com/fusecalc/
# ATMega8 fuse bits (fuse bits for other devices are different!):
# Example for 8 MHz internal oscillator
# Fuse high byte:
# 0xd9 = 1 1 0 1 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000)
# ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0
# | | | | | +-------- BOOTSZ1
# | | | | +---------- EESAVE (set to 0 to preserve EEPROM over chip erase)
# | | | +-------------- CKOPT (clock option, depends on oscillator type)
# | | +---------------- SPIEN (if set to 1, serial programming is disabled)
# | +------------------ WDTON (if set to 0, watchdog is always on)
# +-------------------- RSTDISBL (if set to 0, RESET pin is disabled)
# Fuse low byte:
# 0x24 = 0 0 1 0 0 1 0 0
# ^ ^ \ / \--+--/
# | | | +------- CKSEL 3..0 (8M internal RC)
# | | +--------------- SUT 1..0 (slowly rising power)
# | +------------------ BODEN (if 0, brown-out detector is enabled)
# +-------------------- BODLEVEL (if 0: 4V, if 1: 2.7V)
# Example for 12 MHz external crystal:
# Fuse high byte:
# 0xc9 = 1 1 0 0 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000)
# ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0
# | | | | | +-------- BOOTSZ1
# | | | | +---------- EESAVE (set to 0 to preserve EEPROM over chip erase)
# | | | +-------------- CKOPT (clock option, depends on oscillator type)
# | | +---------------- SPIEN (if set to 1, serial programming is disabled)
# | +------------------ WDTON (if set to 0, watchdog is always on)
# +-------------------- RSTDISBL (if set to 0, RESET pin is disabled)
# Fuse low byte:
# 0x9f = 1 0 0 1 1 1 1 1
# ^ ^ \ / \--+--/
# | | | +------- CKSEL 3..0 (external >8M crystal)
# | | +--------------- SUT 1..0 (crystal osc, BOD enabled)
# | +------------------ BODEN (if 0, brown-out detector is enabled)
# +-------------------- BODLEVEL (if 0: 4V, if 1: 2.7V)
# Tune the lines below only if you know what you are doing:
AVRDUDE = avrdude $(PROGRAMMER) -p $(DEVICE)
TINYAVRDUDE = avrdude $(TINYPROGRAMMER) -p $(DEVICE)
COMPILE = avr-gcc -std=gnu99 -ffixed-2 -ffixed-26 -ffixed-27 -Wall -Os -DF_CPU=$(CLOCK) -mmcu=$(DEVICE)
# symbolic targets:
all: main.hex
.c.o:
$(COMPILE) -c $< -o $@
.S.o:
$(COMPILE) -x assembler-with-cpp -c $< -o $@
# "-x assembler-with-cpp" should not be necessary since this is the default
# file type for the .S (with capital S) extension. However, upper case
# characters are not always preserved on Windows. To ensure WinAVR
# compatibility define the file type manually.
.c.s:
$(COMPILE) -S $< -o $@
flash: all
$(AVRDUDE) -U flash:w:main.hex:i
tinyflash: all
$(TINYAVRDUDE) -U flash:w:main.hex:i
fuse:
$(AVRDUDE) $(FUSES)
tinyfuse:
$(TINYAVRDUDE) $(FUSES)
# Xcode uses the Makefile targets "", "clean" and "install"
install: flash fuse
# if you use a bootloader, change the command below appropriately:
load: all
bootloadHID main.hex
clean:
rm -f main.hex main.elf $(OBJECTS)
# file targets:
main.elf: $(OBJECTS)
$(COMPILE) -o main.elf $(OBJECTS)
main.hex: main.elf
rm -f main.hex
avr-objcopy -j .text -j .data -O ihex main.elf main.hex
# If you have an EEPROM section, you must also create a hex file for the
# EEPROM and add it to the "flash" target.
# Targets for code debugging and analysis:
disasm: main.elf
avr-objdump -d main.elf
cpp:
$(COMPILE) -E main.c