diff --git a/index.md b/index.md
index e8f11914..62fa858e 100644
--- a/index.md
+++ b/index.md
@@ -35,6 +35,7 @@ The ARINC653 execution environment (APEX) is under development.
10. [Running system on `riscv64-generic-spike`](quickstart/riscv64-generic-spike.md)
11. [Running system on `sparcv8leon3-gr716-mini`](quickstart/sparcv8leon3-gr716-mini.md)
12. [Running system on `sparcv8leon3-gr712rc-board`](quickstart/sparcv8leon3-gr712rc-board)
+ 13. [Running system on `sparcv8leon3-gr712rc-board`](quickstart/sparcv8leon3-gr716-mimas)
5. [Loader](loader/index.md)
1. [Architecture](loader/architecture.md)
2. [Command-line interface](loader/cli.md)
diff --git a/quickstart/_images/MimasA7_Mini_Connected.jpg b/quickstart/_images/MimasA7_Mini_Connected.jpg
new file mode 100644
index 00000000..b5adecc8
Binary files /dev/null and b/quickstart/_images/MimasA7_Mini_Connected.jpg differ
diff --git a/quickstart/_images/MimasA7_Mini_WD.png b/quickstart/_images/MimasA7_Mini_WD.png
new file mode 100644
index 00000000..d0ffed20
Binary files /dev/null and b/quickstart/_images/MimasA7_Mini_WD.png differ
diff --git a/quickstart/_images/gr716-mimas-help.png b/quickstart/_images/gr716-mimas-help.png
new file mode 100644
index 00000000..ca3ca928
Binary files /dev/null and b/quickstart/_images/gr716-mimas-help.png differ
diff --git a/quickstart/_images/gr716-mimas-loading.png b/quickstart/_images/gr716-mimas-loading.png
new file mode 100644
index 00000000..fd37a2fd
Binary files /dev/null and b/quickstart/_images/gr716-mimas-loading.png differ
diff --git a/quickstart/_images/gr716-mimas-picocom-send.png b/quickstart/_images/gr716-mimas-picocom-send.png
new file mode 100644
index 00000000..4f6110f1
Binary files /dev/null and b/quickstart/_images/gr716-mimas-picocom-send.png differ
diff --git a/quickstart/_images/gr716-mimas-ps.png b/quickstart/_images/gr716-mimas-ps.png
new file mode 100644
index 00000000..093bba04
Binary files /dev/null and b/quickstart/_images/gr716-mimas-ps.png differ
diff --git a/quickstart/_images/gr716-mimas-start.png b/quickstart/_images/gr716-mimas-start.png
new file mode 100644
index 00000000..602537d1
Binary files /dev/null and b/quickstart/_images/gr716-mimas-start.png differ
diff --git a/quickstart/index.md b/quickstart/index.md
index c68c9932..9f4e5017 100644
--- a/quickstart/index.md
+++ b/quickstart/index.md
@@ -18,7 +18,8 @@ and building artifacts are available in the `_boot` directory. The building proc
10. [Running system on riscv64-generic-spike](riscv64-generic-spike.md)
11. [Running system on sparcv8leon3-gr716-mini](sparcv8leon3-gr716-mini.md)
12. [Running system on sparcv8leon3-gr712rc-board](sparcv8leon3-gr712rc-board.md)
-12. [Table of Contents](../index.md)
+13. [Running system on sparcv8leon3-gr716-mimas](sparcv8leon3-gr716-mimas.md)
+14. [Table of Contents](../index.md)
```{toctree}
:maxdepth: 1
@@ -38,5 +39,6 @@ ia32-generic-qemu.md
riscv64-generic-qemu.md
riscv64-generic-spike.md
sparcv8leon3-gr716-mini.md
-sparcv8leon3-gr712rc-board
+sparcv8leon3-gr712rc-board.md
+sparcv8leon3-gr716-mimas.md
```
diff --git a/quickstart/sparcv8leon3-gr716-mimas.md b/quickstart/sparcv8leon3-gr716-mimas.md
new file mode 100644
index 00000000..34fccd07
--- /dev/null
+++ b/quickstart/sparcv8leon3-gr716-mimas.md
@@ -0,0 +1,107 @@
+# Running system on sparcv8leon3-gr716-mimas
+
+These instructions describe how to run Phoenix-RTOS on the LEON3/GR716 emulated
+on Mimas A7 Mini FPGA which is called `sparcv8leon3-gr716-mimas`target.
+Note that the build artifacts, including the system image should be provided in the `_boot` directory. If you
+have not built the system image yet, please refer to the [Building Phoenix-RTOS image](../building/index.md) section.
+
+## Connecting the board
+
+Connect the board to the computer using a USB cable which provide power to the board (There is pin jumper that
+determinate which power line will be in use).
+
+Communication with the board in this case is provided via USB-UART converters connected to connector `P4`
+
+- pins `3-tx (E13 - red)`&`5-rx (D16 - orange)` are used for interfacing with the `phoenixd` server.
+- pins `7-tx (E15 - yellow)`&`9-rx (F14 - orange)` are used for `psh/plo` console.
+- pins `37-M4` & `49-GND` must be connected via `10k` ohm resistor.
+
+Mimas pinout diagram:
+![Image](_images/MimasA7_Mini_WD.png)
+
+Source: The MimasA7 Mini board's schematic, available on
+
+
+This is how connected device should look like:
+![Image](_images/MimasA7_Mini_Connected.jpg)
+
+## Programming Artix FPGA
+
+All information about preparing and uploading a bit stream for the Mimas A7 Mini can be found in the
+[phoenix-rtos-hdl](https://github.com/phoenix-rtos/phoenix-rtos-hdl/blob/master/leon3-numato-mimas-a7-mini/README.md)
+repository.
+
+`Note: Do not run further steps until FPGA isn't programed properly.`
+
+## Copying system image using PHFS (phoenixd)
+
+To load the disk image on the board, first step is to verify which device the `plo` serial interface is connected to
+using the following command:
+
+```bash
+ls -l /dev/serial/by-id
+```
+
+The output of this command depends on what interfaces are used. (Easiest way to determinate which one are correct is
+run this command, unplug one of them and again using same command check what device disappears).
+
+To provide the disk image to the bootloader, `phoenixd` has to be launched with the following arguments
+(choose suitable ttys device, in this case, USB-UART converter is connected to pins `3 & 5`):
+
+`-s` option to `phoenixd` determines from where program will upload files to the device. To simplify this process,
+we can just move to the desired folder and use `.` to point to the current directory.
+To do that simply type:
+
+```bash
+cd _boot/sparcv8leon3-gr716-mimas
+```
+
+then
+
+```bash
+sudo ./phoenixd -p /dev/ttyUSB[X] -b 115200 -s .
+```
+
+In a second terminal start `picocom` using the following command:
+
+```bash
+picocom --imap lfcrlf -b 115200 -r -l /dev/ttyUSB[X] --send-cmd cat
+```
+
+After resetting the board using the `BTN0` button, you should see `Bootloader` message in the terminal. To load the
+bootloader (`plo`) to the RAM, send the image using `picocom --send-cmd`. Type `Ctrl+a` followed by `Ctrl+s`,
+enter the path to the `plo.img` file and press `Enter`. The file is located in the `_boot/sparcv8leon3-gr716-mimas`
+directory. Refer to the image below:
+
+![Image](_images/gr716-mimas-picocom-send.png)
+
+If the image has been loaded correctly, you should see system startup logs.
+
+![Image](_images/gr716-mimas-loading.png)
+
+## Using the Phoenix-RTOS
+
+After loading, Phoenix-RTOS will be launched and the `psh` shell command prompt will appear in the terminal.
+
+![Image](_images/gr716-mimas-start.png)
+
+To get the available command list type:
+
+```console
+help
+```
+
+![Image](_images/gr716-mimas-help.png)
+
+To get the list of working processes type:
+
+```bash
+ps
+```
+
+![Image](_images/gr716-mimas-ps.png)
+
+## See also
+
+1. [Running system on targets](index.md)
+2. [Table of Contents](../index.md)