esp8266-example.yaml

substitutions:
  name: apc-ups
  device_description: "Monitor and control a APC UPS via RS232"
  external_components_source: github://samoswall/esphome-apc-ups@main
  tx_pin: GPIO4
  rx_pin: GPIO5

esphome:
  name: ${name}
  comment: ${device_description}
  project:
    name: "samoswall.esphome-apc-ups"
    version: 1.0.0

esp8266:
  board: d1_mini

external_components:
  - source: ${external_components_source}
    refresh: 0s

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

ota:
logger:

# If you don't use Home Assistant please remove this `api` section and uncomment the `mqtt` component!
api:

# mqtt:
#   broker: !secret mqtt_host
#   username: !secret mqtt_username
#   password: !secret mqtt_password
#   id: mqtt_client

uart:
  - id: uart_0
    baud_rate: 2400
    tx_pin: ${tx_pin}
    rx_pin: ${rx_pin}
    debug:
      direction: BOTH
      dummy_receiver: false
      after:
        delimiter: "\n"
      sequence:
        - lambda: UARTDebug::log_string(direction, bytes);

apc_ups:
  - id: ups0
    uart_id: uart_0

binary_sensor:
  - platform: apc_ups
    apc_ups_id: ups1
    runtime_calibration:
      name: "${name} runtime calibration"
    smart_trim:
      name: "${name} smart trim"
    smart_boost:
      name: "${name} smart boost"
    on_line:
      name: "${name} on line"
    on_battery:
      name: "${name} on battery"
    output_overloaded:
      name: "${name} output overloaded"
    battery_low:
      name: "${name} battery low"
    replace_battery:
      name: "${name} replace battery"
    smart_mode:
      name: "${name} smart mode"

switch:
  - platform: apc_ups
    apc_ups_id: ups1
    front_panel_test:
      name: "${name} front panel test"
    simulate_power_failure:
      name: "${name} simulate power failure"
    self_test:
      name: "${name} self test"
    start_runtime_calibration:
      name: "${name} start runtime calibration"
    save_last_battery_change_date:
      name: "${name} save last battery change date"
    shutdown_with_grace_period:
      name: "${name} shutdown with grace period"
    soft_shutdown:
      name: "${name} soft shutdown"
    shutdown_immediately:
      name: "${name} shutdown immediately"
    turn_on:
      name: "${name} turn on"
  - platform: restart
    name: "${devicename} restart"

sensor:
  - platform: apc_ups
    apc_ups_id: ups1
    battery_voltage:
      name: "${name} battery voltage"
    grid_frequency:
      name: "${name} grid frequency"
    grid_voltage:
      name: "${name} grid voltage"
    ac_output_voltage:
      name: "${name} ac output voltage"
    ac_output_load:
      name: "${name} ac output load"
    status_bitmask:
      name: "${name} status bitmask"
    state_of_charge:
      name: "${name} state of charge"
    estimated_runtime:
      name: "${name} estimated runtime"
    internal_temperature:
      name: "${name} internal temperature"
#    ambient_temperature:
#      name: "${name} ambient temperature"
    max_grid_voltage:
      name: "${name} max grid voltage"
    min_grid_voltage:
      name: "${name} min grid voltage"
    nominal_battery_voltage:
      name: "${name} nominal battery voltage"
    nominal_output_voltage:
      name: "${name} nominal output voltage"

  - platform: wifi_signal
    name: "${devicename} wifi signal"
    update_interval: 600s

  - platform: uptime
    name: "${devicename} Uptime in Days"
    id: uptime_sensor_days
    update_interval: 60s


text_sensor:
  - platform: apc_ups
    apc_ups_id: ups1
    cause_of_last_transfer:
      name: "${name} cause of last transfer"
#    protocol_info:
#      name: "${name} protocol info"
    firmware_revision:
      id: "myfirmware"
      name: "${name} firmware revision"
    old_firmware_version:
      id: myoldfirmware
      name: "${name} old firmware version"
    manufacture_date:
      name: "${name} manufacture date"
    last_battery_change_date:
      name: "${name} last battery change date"
    local_identifier:
      name: "${name} local identifier"
    serial_number:
      name: "${name} serial number"
    self_test_results:
      name: "${name} self test results"
    model_name:
      name: "${name} model name"
    last_battery_change_new_date:
      name: "${name} last battery change new date"

  - platform: version
    name: "$devicename Version"

  - platform: wifi_info
    ip_address:
      name: "$devicename IP"
    bssid:
      name: "$devicename BSSID"


time:
  - platform: sntp
    id: sntp_time
    timezone: Europe/Moscow


datetime:
  - platform: template
    id: my_datetime_date
    type: date
    name: Change battery date
    optimistic: yes
    on_value:
      then:
        - lambda: |-
           id(ups1).set_last_battery_change_new_date(x.strftime("%m/%d/%y"));