Home
Hello and welcome on bId°°'s wiki!!
póUPrè is a 16x sample player. When your sample is loaded via the right click menu the red light becomes green. You have 16 channels to pick sounds in the sample. On each channel you can define the starting point, the length and the speed of the segment picked in the sample. You can choose between 2 types of trig behavior:
- trig : the segment will be played and then stopped when reaching its length
- gate : the segment is read while the trig input is at +10V. If the trig is still activated at +10V when reaching the segment length if loop is enabled the segment will be read again until the trig input is released.
All ports are polyphonic so you can automate every param with CV with the help of vcv merge modules.
To connect the output use a vcv split.
The current version doesn't re-sample the sample when its sample rate is not the same as the engine's one. There is no zero crossing algorithm when setting start and length so you might hear some clicks.
maGma is a póUPrè with a filter on each channel. You can disable the filter or choose between LP, BP and HP.
LP can be useful to remove or attenuate some clicks.
Sequencer.
Multiband distortion.
liMonADe is a wave table oscillator.
Its oscillator can read up to 256 wave cycles (that I call frames) of 2048 samples each.
You can design your own wave cycles by setting their frequencies magnitude and phase or you can import ready to run wave tables.
-
Those three buttons allows you to toggle on/off the 3D display (12), the edited wave cycle display (2) and the played wave cycle display (2).
-
The edited and played wave cycles can be displayed on top of the spectrum management window.
-
The spectrum management window allows you to modify magnitude and phase of each partial of the edited wave cycle. Each time you change a parameter in this window the selected wave cycle is updated accordingly. You can edit high frequencies with the help of the horizontal scroll bar on the bottom of the window.
In the picture above the wave table contains 5 wave cycles, the edited wave cycle is the first one, displayed in green in the 3D view (12) and in the 2D view (2), and the played one is the fourth, displayed in red in (12) and (2). In order to select the edited wave cycle use the green button (4). In order to select the played wave cycle use the red button (13).
-
Edited wave cycle selection button
-
This text box allows you to change the default number of samples per wave cycle used when opening ready made wave tables. Most part of the free wave tables available are made of 2048 samples length wave cycles. If your wave table is made of 1024 samples wave cycles for example you have to change that value before opening the wave table. When reading the file liMonADe will split the file in n x 1024 samples wave cycles and interpolate them on the 2048 samples available per frame. In our example if you don't change the number of samples you will see two wave cycles per frame.
-
In order of appearance, the first button stands for opening wave tables, the second one for opening pictures (png) and the last one for opening a single wave cycle.
Reverb based on Freeverb with a pitch sifter in the feedback loop. Quite unstable but can produce nice textures.
Portage of Gverb.
Image to sound. Load a png via the menu and EMILE reads the picture as a spectrogram. Low frequencies are at the bottom of the picture.
LP filter using FFT.
Diplays the real time spectrum of the incoming signal.
Pitch shifter.
Comparator. If the sum of the 3 weighted inputs is greater than the floor of the output the output sends +10V, if not 0V.
Mid/Side decoder/encoder
Draw the FFT in order to define your cycle waveform.
rabBIT is a bit crusher. The left column let you disable bits and the right one reverse bits. For example if your current sample is 01100101 if you disable the last bit you obtain 01100100. If you reverse the 5th and 6th bits you obtain 01101000. Be careful with your monitors it can produce very distorted sounds.
dTrOY is a single line sequencer but with nice features inspired by Roland 185, DU-SEQ, Metropolis hardware sequencers. dTrOy = Detroit + Toy ...
Features:
- 8 triggers with pitch, number of pulses, slide and skip parameters
- Each trig has its own gate mode :
- closed 0.0V on pulses
- first pulse opened 10.0V then closed
- each pulse opened according to gate time setting
- fully opened
- fully opened passing Gate 1 input (you can send gates or audio :) )
- fully opened passing Gate 2 input
- Up to 16 steps per pattern
- 5 play modes : forward, backward, ping-pong, random, random neighbor
- 2 count modes : steps and pulses
- Scale quantization and root note
- Sync & reset sequencer
- 16 patterns
bordL is based on dTrOY but it is a little bit more powerful. I have removed the sliders to put more controls. So from top to bottom, you have big pitch knobs and little random pitch knobs. Then you have a secondary CV line that is linked to the "V" output with a line of big knobs for value (not quantized .. continuous voltage) and a line with small knobs for randomness. You can use that line to animate an accent or what you want. The pulse controls have small buttons to setup the probability for the gate to be opened at 100% or closed at 0%.
OUAIve is a sample player ...
Features:
- TRIG Mode :
- sample start position CV controlled by POS
- play triggered by TRIG CV
- sample play rate CV controlled x0.5 to x10. No time stretching just vinyl like speed change
- GATE Mode :
- free control on play head by CV on POS
- play opened by GATE CV
- SLICE Mode :
- up to 128 slices CV controlled (I know 128 is a little bit too much but can lead to produce strange sounds)
- 3 slices play modes => forward, backward and repeat. CV controlled
- sample play rate CV controlled x0.5 to bla bla bla ...
- slice index selection follows triggers but can be overridden by POS
ChUTE is a space/strange trigger based on the free fall and bouncing of an object. You can change the drop altitude between 1cm and 3m, the gravity in between the Moon's one and Neptune's one. Earth is the default. And you can adjust the C.O.R. meaning the coefficient of restitution. Outputs provide a gate based on downside movements, the relative tension regarding the altitude ALT and TOP which exposes the tops of the rebounds.
dUKe is a simple but very efficient 4 x CV controller. Yo can choose between -5V/+5V or 0V/10V and set the MAX and MIN for each slider. If used CV will add signal on top of the slider. Two nice buttons allow you to jump to both extremities of the 4 sliders at the same time.
ACnE is a very simple and compact patch bay/mixer. 16 in x 8 out. For a faster patching, reset is still the right click on knobs but with ACnE center click set them to their maximum value. You have 16 scenes you can choose from and a copy/paste function that allows you to quickly initialize them. Mute on all outputs, Mute and Solo on all inputs. Main outputs have a dedicated volume control. Ramp param allows smooth transitions between scenes.
Just 16 scenes of 16 CV controllers and a fader to morph between them. All outputs can be switched between -5v/+5v and 0v/10v. Each control can be switched between two modes (click on the little light at the bottom right of each button to toggle, default is Morph):
- Morph = light off -> the value of the control will be rescaled all along fader movements
- Target = light on -> the value of the control will be updated only when the fader reaches the highest value
Takes a clock in input and applies a delay on even ticks to create swing. Reset set the next tick of the incoming clock to odd.
TiARE is a phase distortion oscillator based on VCO1 meaning that you have the same 4 waves but you can modify how they are generated within each cycle. By default the phase is linear meaning that oscillators behave as VCO1 but if you speed up or slow down the phase in a part of the cycle then you will morph the waveform accordingly. You can shape manually the phase curve or automate it by X and Y CVs.
It is a phase distortion oscillator like TiARE but here you have only one output and each cycle is split in 4 parts. You can choose your wave form and phase distortion per part.
ForK is an oscillator based on a particular approach of formant synthesis. It is the first attempt of an adaptation of Paul Sernine and Doc Rochebois's work (http://www.musicdsp.org/pdf/musicdsp.pdf). Warning this model creates DC offset at high frequencies. Vowels sounds are more fun at low and mid frequencies. You can tweak frequency F and gain G on 4 bands. Presets button lets you hear typical french vowels settings.
Is a stereo peak compressor showing 300ms and 100ms RMS of the signal. Nothing really crazy, controls are standards..
Is a mono version of bAR
Is 4th order stereo LP ladder filter. By default the model is linear, in that case GAIN is an output gain to compensate global signal energy loss at high resonance. If you switch to non linear, a non linear tanh() function is applied to the signal in each stage and GAIN becomes the gain factor of that function.
Is simple LP,BP,HP filter.
Is a 16 bands vocoder. A and D stands for the attack and decay of the envelope follower. MOD CAR and OUT are gain stages for each channel.
Clock with triplets and measure management.
Is a live sampler. You can chose between two REC modes, the first one each record replaces the previous, the second mode allows to stack samples. You can delete a slice by right clicking the waveform. You can chose between two inputs for Gate or Trig and 3 slice play modes : one shot, repeat and ping pong. The menu allows you to delete slices and add/remove slice markers. You can load/save samples too. You can split the sample with transient detection via the right click menu and set the sensitivity with the little knob under the EOC (End Of Cycle) output.
mp3/pls/m3u stream player. Put a valid url in the text field and push listen. That's all :)
μ. can be viewed as a step in a sequence. Link some of them and you will build a full sequence path. When moving the cursor over the knobs and ports the display shows a description and the current value of the focused object. As usual black ports are inputs and the red ones outputs. To start experimenting link some units with bpm ports so the first one will become the master tempo for the chain. Link gate and CV at the bottom to create the path for the signal. Link step end ports with step start ones to build the order of steps. At that stage you can use the alternate end of step output port to fork the path and adjust the corresponding probability. Maybe you need that under some circumstances a step is stopped .. use the inhibit port. Once the chain is made set the tempo with the first step (one fast knob and a dedicated one for decimals). Then set the length of each step (two controls too as for bpm) 100% means a quarter for a 4/4 signature, 50% one eighth, 200% an half etc... To introduce swing use decimal values for the step length. Now choose the length of the trigs in percentage of the step length, the CV value, the probability of the trig to be played, the probability of the alternate port to be use instead of the standard end of step port, the trig repeat count and the distance between retrigs. If the trig length is greater than the distance then the trigs will merge. You have two small led buttons between gate and CV in and out ports. They activate the stack mode on those ports. By default a step plays its trigs when active and let the signal pass thru the ports when not active. If you activate the stack mode the incoming signal will be added to the trigs data when the step is active. You can manually launch a step with the left top led button and mute the step with the right one. Modulation ports are available for almost all parameters.
vOId is the ultimate mastering tool for Rack. Once plugged in your Rack you gonna sound FAAAAT. Picture is taken from a very good LP of TERA MELOS.