-
Notifications
You must be signed in to change notification settings - Fork 0
/
board.h
141 lines (122 loc) · 4.07 KB
/
board.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
/*
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
2011 Giovanni Di Sirio.
This file is part of ChibiOS/RT.
ChibiOS/RT is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/RT is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the R2P DC motor module.
*/
/*
* Board identifier.
*/
#define BOARD_R2P_DCM_MODULE
#define BOARD_NAME "R2P Demo module"
/*
* Board frequencies.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 8000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F10X_MD
/*
* IO pins assignments.
*/
#define LED_GPIO GPIOA
#define LED1 0
#define LED2 1
#define LED3 2
#define LED4 3
#define BUTTON_GPIO GPIOB
#define BUTTON1 1
#define BUTTON2 0
#define TEST_GPIO GPIOA
#define TESTOUT 4
#define TESTIN 5
#define TESTOD 6
#define SERIAL_DRIVER SD1
#define CAN_DRIVER CAND1
#define PWM_DRIVER PWMD3
#define ICU_DRIVER ICUD4
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
* PA0 - Push Pull output (LED1).
* PA1 - Push Pull output (LED2).
* PA2 - Push Pull output (LED3).
* PA3 - Push Pull output (LED4).
* PA4 - Push Pull output (test signal).
* PA5 - Normal Input (test signal).
* PA6 - Open Drain output (test signal).
* PA7 - Alternate output (PWM3 CH2).
* PA9 - Alternate output (USART2 TX).
* PA10 - Normal input (USART2 RX).
*/
#define VAL_GPIOACRL 0xB7433333 /* PA7...PA0 */
#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup.
* Everything input with pull-up except:
* PB0 - Normal input with pull-up (BUTTON2).
* PB1 - Normal input with pull-up (BUTTON1).
* PB1 - Normal input (ICU4 CH1).
* PB8 - Normal input (CAN1 RX).
* PB9 - Alternate output (CAN1 TX).
*/
#define VAL_GPIOBCRL 0x88888848 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x888888B4 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */