Sump pump basin water depth monitor, logging, and alerts
Copyright(C) 2021, BrucesHobbies, All Rights Reserved
Sump pump basin/well/pit monitoring is important as one tool for preventing basement flooding in homes and buildings. This is a DIY project for the Raspberry Pi or similar system using an inexpensive sensor with a couple of wires. The software is written in Python and runs under Linux. A number of different sensor types are supported.
There are dozens of ultrasonic range finder based sump pump basin/well/pit monitoring programs written and on GitHub for the RPi. One common theme is that Ultrasonic range finders can be difficult to install in the basin due to the confined space since the basin has inside it a primary sump pump, in some cases a secondary pump in case the primary pump fails, pipes, and float switches. The ultrasonic signal will echo off the different objects making it difficult for the ultrasonic range finder to distinguish the intended return echo. Second, the programs that I looked at were not very robust since a simple polling loop could loop endlessly if the return signal was missed. This project takes a different approach with the use of an ultrasonic range finder using events instead of polling.
In addition this program implements a novel alternative approach to measuring water depth using a low-cost Honeywell pressure sensor. The pressure sensor looks at the water pressure at the bottom of the basin. The pressure sensor involves a little bit more work up front but is significantly easier to install and more reliable.
The Raspberry Pi looked like an ideal platform to monitor and log sump basin water depth. This open source project supports two different types of sensors. You may use either or compare both.
- Ultasonic range finder: HC-SR04
- Pressure sensor: Honeywell ABP series
This open source program logs the water depth and will send email alerts if the water depth exceeds an alert level. Options include Comma Separated Variable (CSV) file, MQTT, and/or InfluxDB. It can also send status reports on a periodic interval. The alerts and status messages can be an email or SMS message sent via email. Feel free to contribute with custom alert options. The program is written in Python and can be ported to additional platforms. The program runs from a terminal window or at boot.
plotBasinMaster.py plots the water depth log. You can view the plots and pan/zoom to specific time periods for the measurements. It uses MatPlotLib and is easy to customize to plot what is of interest to you.
Figure 1 shows the installation of the ultrasonic range finder on the sump basin lid and the pressure sensor tube for the recommended alternative approach.
For the two types of sensors, here are the results:
| Trial Results | Ultrasonic | Pressure Sensor |
|---|---|---|
| Standard deviation of readings | 0.62" | 0.14" |
| Minimum reading (delta from average) | -4.28" | -0.29" |
| Maximum reading (delta from average) | +2.57 | +0.39 |
For the ultrasonic sensor, to solve the problems mentioned in the preface with echos from objects inside the basin, I placed the ultrasonic range finder inside an open ended PVC pipe that was put in the the basin. The open source code that I saw used polling which can easily be an endless loop if the echo pulse is not found. Event detection logic instead of polling is more robust which was implemented. We then use the average of 11 readings with a threshold of needing 6 good readings that passed a reasonablness distance test. 11% of the attempts failed to have sufficient measurements to average. We can see that the standard deviation is reasonably small but there are large outliers as evidenced by the large minimum and maximum reading. More sophisticated algorithms could be developed but the pressure sensor was a better choice to build on.
For the pressure sensor, I used a single reading without additional processing. The standard deviation is reasonably small and there are no large outliers as evidenced by the minimum and maximum readings. For the pressure sensor I used standard air supply tubing that is sold for aquariums. Unfortunately after several days, the pressure from the submerged tube leading to the above basin sensor would slowly leak. To solve this, I used an inexpensive aquarium pump to pressurize the system with a relay to turn it on and off.
As an Amazon Associate I earn a small commission from qualifying purchases. It does not in any way change the prices on Amazon. I appreciate your support, if you purchase using the links below.
- HC-SR04 Amazon: HC-SR04
- 1k ohm and 2K ohm resistors to divide 5 volt signal down to 3.3 volts input for RPi
- Wire, heat shrink tubing, soldering iron, and solder
- Honeywell ABPMAND001PG2A3, ABPDRRV001PDSA3 or ABPMRRV060MG2A3 pressure sensor available from Digikey, Mouser, Arrow, Newark, etc. for around $13 USD
- Amazon: Plastic tube 1.6mm ID
- Amazon: Standard Airline Tubing
- Optional Amazon: Air-pump with check valve
- Optional Amazon: Air line adapters including tee
- Optional Amazon: 5Vdc Relay
- Wire, heat shrink tubing, soldering iron, and solder
The ABPMRR060MG2A3 which is a 2-wire I2C bus interface but in a surface mount package which requires soldering. The I2C pull up resistors are not required when used with the RPI. The ABPDRRV001PDSA3 which is a 3-wire SPI bus interface in a DIP package (Dual-Inline Package used with prototype/breadboards). Both are 3.3 Vdc supply voltage.
- Raspberry Pi (any of the following)
- Power adapter for your Raspberry Pi
- Heatsinks (optional)
- SD-Card
For installing the Raspberry Pi operating system, you may want a USB keyboard and USB mouse along with an HDMI cable and monitor. If using the RPI4, a Micro-HDMI to HDMI adapter may be needed. It is possible to install the operating system without a keyboard, mouse, and monitor, but simpler is sometimes better. Once installed and configured you may want to switch to SSH or remote desktop so that you can remove the monitor, mouse, and keyboard.
| RPI | HC-SR04 |
|---|---|
| Pin 2 (5Vdc) | Vcc |
| Pin 6 (GND) | GND |
| Pin 16 (GPIO23) | TRIG |
RPi inputs cannot be exposed to voltages less than 0 or greater than 3.3 volts. For ECHO out of the sensor the voltage is 5 volts. One approach of converting it to 3.3 volts is to feed the ECHO out to a voltage divider. This can be made from 1K ohm and 2K ohm resistors in series with the 1K ohm to the ECHO and the 2K ohm to ground. The RPi pin 18 (GPIO24) goes to the 1K and 2K ohm center tap as shown below.
ECHO >--+
|
1K ohm
|
+---> RPi p18
|
2K ohm
|
GND ----+---- RPi GND
Figure 2: Ulrasonic Range Sensor Wiring
Each Honeywell pressure sensor is either i2c or SPI, but not both. The ABPDRRV001PDSA3 which is a 3-wire SPI bus interface is recommended as it is a DIP package.
RASPBERRY PI SPI PINS to ABP PRESSURE SENSOR (5-wires total):
| RPI 40-pin | SPI ABP (From Table 8 in Honeywell Data Sheet) |
|---|---|
| Pin 17 (+3.3 VDC) = | Pin 2 (+3.3 Vsupply) |
| Pin 21 (SPI_MISO) = | Pin 5 (MISO) |
| Pin 23 (SPI_CLK) = | Pin 6 (SCLK) |
| Pin 24 (SPI_CE0_N) = | Pin 3 (SS) |
| Pin 25 (GND) = | Pin 1 (GND) |
RASPBERRY PI PINS to ABP I2C PRESSURE SENSOR (4-wires total):
| RPI 40-pin | I2C ABP (From Table 8 in Honeywell Data Sheet) |
|---|---|
| Pin 1 (+3.3 VDC) = | Pin 2 (Vsupply) |
| Pin 3 (SDA1) = | Pin 5 (SDA) |
| Pin 5 (SCL1) = | Pin 6 (SCL) |
| Pin 6 (GND) = | Pin 1 (GND) |
The 3.3 VDC pressure sensors are recommended but, if you purchased a 5.0 VDC pressure sensor then the 5 VDC supply on the pressure sensor pin 2 would go to the RPI Pin 2 (+5.0 VDC). You will need to convert the ABP’s 5 volt bus signals to the RPI bus 3.3 volt levels so this is not as straight forward as using the 3.3 VDC pressure sensor.
| RPI | Pump relay driver |
|---|---|
| Pin 12 (GPIO18) | Trigger |
| Pin 14 (GND) | Driver- / Gnd |
| Pin 4 (5Vdc) | Driver+ / Power |
You will purchase either an SPI or I2C pressure sensor, not both. The SPI version is recommended but both sets of
photos are included to provide choices.
Figure 3: SPI Pressure Sensor
Figure 4: SPI Wiring on RPI
Figure 5: Alternative I2C Pressure Sensor Power Pins
Figure 6: Alternative Pressure Sensor I2C Bus
Figure 7: Alternative I2C Wiring on RPI
If your standard airline tubing has a slow leak like mine, consider buying an aquarium bubbler. Connect the air supply hose to an aquarium bubbler pump, then the one-way check valve that is included with the bubbler, then a "tee" with one side going to the ABP pressure sensor and the other side into the sump basin. The relay can be used to turn the pump on and off, but the pump draws only 2 watts (less than half the power of a nightlite).
Figure 8: Pressure Sensor Installation
Here are the instructions to install the Raspberry Pi Operating System. Raspberry Software Install Procedure
Before continuing make sure your operating system has been updated with the latest updates.
sudo apt-get update
sudo apt-get upgrade
sudo reboot now
If using a Honeywell I2C pressure sensor you will need this library. I would recommend installing it as you may want to use I2C in this project or others. If you don’t install python3-smbus, you will need to comment out the appropriate lines in the program code.
sudo apt-get install python3-smbus
sudo raspi-config
Under interface options, enable either or both the SPI and I2C interfaces depending on the Honeywell ABP pressure sensor that you purchased. In general it is better to enable both so that the interfaces are available for use with projects.
To verify i2c operation, if you have an i2c Honeywell pressure sensor type the following command which should result in the i2c device address 0x28 being displayed:
sudo i2cdetect –y 1
To verify SPI operation, type the following command which should result in the SPI bus being listed:
ls /dev/*spi*
There are several python source files: basinMaster, sensorHnyAbp, hc_sr04_range, sendEmail, and cfgData. To get a copy of the source files type in the following git command assuming you have already installed git:
git clone https://github.com/BrucesHobbies/basinMaster
If you desire, you may edit basinMaster.py and change the user configuration section at the beginning of the file.
Edit the basinMaster.py program file if you used a different sensor than the ABPDRRV001PDSA3. Then change the statement to match the variable range, units, and output type of the sensor you purchased. For example if you purchased the ABPMRRV060MG2A3 change from “001PDS” to “060MG2”. Again, this statement is in the basinMaster.py file. More complete details are found in “sensorHnyAbp.py”.
sensor = sensorHnyAbp.SensorHnyAbp("001PDS")
If alerts are enabled (statusMsgEnabled=1) and you have entered valid email information you can choose to have a status message sent for a RPI well-being check. To change the time of day for the status message from noon local time, edit the hour and minute. Entering values outside the expected values will allow you to disable status messages. Range for HH is 0 -23 and for MM is 0 – 59.
If using the ultrasonic sensor, set the basin/well/pit depth.
Set the WATER_DEPTH_ALERT level to the water depth at which to send alert messages. If alerts are enabled, you can choose to throttle the alerts. The interval can be as short or long as you like. Default is 24*3600 seconds which is one day.
#
# --- User Email Alerts Configuration ---
#
# First time program starts, it will ask you for the sender's email
# this should be an email that you have established for sending alerts from this program
# gmail is suggested with "Less Secure App Access" turned on. This is required for Python on the RPI.
# If you change passwords, you will need to delete cfgData.json so that this program will again ask for the password.
#
statusMsgEnabled = 1 # non zero enables sending of email / SMS text messages
statusMsgHHMM = [12, 10] # Status message time to send [hh, mm]
alertMsgEnabled = 0 # non zero enables sending of email / SMS text messages
WATER_DEPTH_ALERT = 9 # Send alert when water depth greater than this many inches
WATER_DEPTH_ALERT_ENABLE = 1 # Enable sending alerts
minIntervalBtwWaterEmails = 24*3600 # seconds
You can use Google Gmail to send status and alert emails. Others have also used Microsoft Live/Outlook/Hotmail, Yahoo, Comcast, ATT, Verizon, and other email servers. Currently, status and alert messages are sent by email which can also be sent as an SMS text to your cell phone. Gmail works with Python on the Raspberry Pi if you set the Gmail security settings to low. As such, you can create a separate Gmail account to send messages from. Under your Gmail account settings you will need to make the following change to allow “Less secure app access”.
Then click on “Turn on access (not recommended)” by moving the slider to ON. Then click the back arrow.
When your first email is sent at program startup, Google will ask you to confirm that it is you. You will need to sign into the device email account that you created and go to the critical security email that Google sent you and confirm you originated the email before Google will allow emails to be sent from your Python program.
Once you have created an account, start the basinMaster™ program. Type:
python3 basinMaster.py
The first time the program starts up it will ask you for your gmail user id and password for the account that you just created to work with this program. The password will be saved to a file called cfgData.json. Please be careful to not send that file to others. If you ever change your password you will need to delete cfgData.json so that the program will ask you for your password again.
Enter sender’s device email userid ([email protected]):
[email protected]
Enter password:
password
Next the program will ask you for the recipient email address. This can either be the same email address, your primary email address or your SMS cell number carrier’s gateway. To email an SMS to your cell phone construct the recipient email depending on your cell phone carrier:
| Carrier | Format |
|---|---|
| AT&T | [email protected] |
| Verizon | [email protected] |
| Sprint PCS | [email protected] |
| T-Mobile | [email protected] |
| VirginMobile | [email protected] |
Enter recipient’s device email userid ([email protected]):
[email protected]
Please feel free to fork and contribute or provide feedback on priorities and features. Edit pubScribe and uncomment the ENABLE options for your selections.
- Email: supported
- Comma Separated Variable (CSV) file: supported
- Relay / buzzer
- MQTT: supported
- OpenHab
- Home Assistant
- Domoticz
- IFTT
- PubNub
- Twilio
- Cellular
- APRS
On the first time basinMaster™ program starts, it will ask you for your email userid and password for the email account that you created to use for the alerts and status messages. Once you have entered a password the program will send an email message indicating the program has started up. basinMaster™ will then display the first readings according to the type of sensor you selected. To test the status feature, wait for the status time and verify that you received a status message.
Simply open a new terminal window. Switch to the directory.
python3 plotBasinMaster.py
Use the buttons on the bottom of the plot windows to zoom and pan to the specific months, weeks, days, or hours of interest.
Type the following command:
sudo crontab –e
Select the type of editor you are familiar with. I used nano. Add the following line at the end of the file and then press ctrl+O to write the file and ctrl+X to exit the nano editor.
@reboot sleep 60 && cd basinMaster && python3 basinMaster.py
Let us know what you think of this project and any suggestions for improvements. Feel free to contribute to this open source project.