Skip to content

AvalonMiner error code

Mikeqin edited this page May 8, 2017 · 1 revision
CODE NAME TYPE MEMO What to do
1 CODE_IDLE WARN Idle Check if the network is ok or AUC work normally
2 CODE_MMCRCFAILED WARN IIC rx irc mismatch was found Ignore it please, If CGMiner is restart, It will be ok.
4 CODE_NOFAN FATAL Fan cann't be found Check the fan connection
8 CODE_LOCK WARN Reserved Ask for unlock service
16 CODE_APIFIFOOVERFLOW WARN API fifo overflow flag It's just a notice on api fifo
32 CODE_RBOVERFLOW WARN Nonce ringbuffer overflow Ignore it please, If CGMiner is restart, It will be ok.
64 CODE_TOOHOT FATAL The modular or mm board is too hot Check the fan or replace the too hot module
128 CODE_HOTBEFORE WARN Toohot was found on MM It's just a notice for too hot modular
256 CODE_LOOPFAILED FATAL loopback test failed The led will turn to red. Ignore it if hashrate is not so bad.
512 CODE_CORETESTFAILED WARN Core test failed Ignore it if hashrate is not so bad
1024 CODE_INVALIDPMU FATAL Invalid pmu firmware version or pmu is broken Replace a new pmu
2048 CODE_PGFAILED FATAL Power not good Check the PMU
4096 CODE_NTC_ERR FATAL Temperature sensor check failed Replace the module which the code was found on.
8192 CODE_VOL_ERR FATAL Voltage input sensor check failed Replace the module which the code was found on.
16384 CODE_VCORE_ERR FATAL Voltage output sensor check failed Replace the module which the code was found on.
32768 CODE_PMUCRCFAILED WARN It's just a notice Ignore it please
65536 CODE_INVALID_PLL_VALUE WARN PLL configration check failed Reboot the modular, if not good then try to replace the module.
131072 CODE_HUFAILED WARN HU configration check failed Reboot the modular, if not good then try to replace the HU.
TYPE meaning:
  '''WARN'''-It designates potentially harmful situations, but you can ignore it.
  '''FATAL'''-It designates very severe error events that will presumably lead the Avalon7 to crash.
错误码 名称 类型 问题 如何处理
1 CODE_IDLE 提示 空闲 检查网络连接,检查AUC3,检查AUC3数据线是否正常以及正确连接
2 CODE_MMCRCFAILED 提示 MM数据通信中有CRC错误 忽略
4 CODE_NOFAN 警告 没有检测到风扇 检查风扇连接线是否松动,最后尝试更换风扇
8 CODE_LOCK 提示 保留 忽略
16 CODE_APIFIFOOVERFLOW 提示 API缓冲区溢出标示 忽略
32 CODE_RBOVERFLOW 提示 NONCE缓冲区溢出标示 忽略
64 CODE_TOOHOT 警告 MM、PMU或者算力板过热 检查风扇,检查进气口温度,检查环境温度
128 CODE_HOTBEFORE 提示 曾经出现过过热保护的情况 忽略
256 CODE_LOOPFAILED 提示 回环测试提示 忽略
512 CODE_CORETESTFAILED 提示 芯片测试提示 忽略
1024 CODE_INVALIDPMU 警告 PMU没有检测到 更新PMU固件,如果不能修复需更换PMU
2048 CODE_PGFAILED 警告 供电异常 检查电源,检查电源连接线,最后检查PMU是否损坏
4096 CODE_NTC_ERR 警告 PMU上温度传感器检查失败 更换相应模块,保存PMU模块用于北京工厂返修
8192 CODE_VOL_ERR 警告 模组电压输入检测失败 检查电源, 检查电源连接线,更换PMU
16384 CODE_VCORE_ERR 警告 模组电压输出检测失败 检查电源, 检查电源连接线,更换PMU
32768 CODE_PMUCRCFAILED 提示 PMU通信中有CRC错误 忽略
65536 CODE_INVALID_PLL_VALUE 提示 PLL配置检测失败 重启模组
131072 CODE_HUFAILED 提示 HU配置检测失败 重启模组, 如果此HU配置检测仍失败,则更换此HU