Skip to content

Lora-net/picoGW_mcu

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

6 Commits
 
 
 
 
 
 
 
 

Repository files navigation

 / _____)             _              | |    
( (____  _____ ____ _| |_ _____  ____| |__  
 \____ \| ___ |    (_   _) ___ |/ ___)  _ \ 
 _____) ) ____| | | || |_| ____( (___| | | |
(______/|_____)_|_|_| \__)_____)\____)_| |_|
  (C)2017 Semtech-Cycleo

LoRa Pico Cell Gateway project - MCU firmware

1. Components


This directory contains the sources code of the Keil project to build a Picocell Gateway MCU firmware based on the Semtech LoRa Picocell Gateway reference design. The target MCU is a STM32F401CD. The firmware implements either a USB CDC protocol or a UART protocol to bridge commands coming from host to the SX1308 SPI interface. The embedded firmware takes in charge the power management of the SX1308 during the downlink to respect the 500MA max power constraint in the USB plug.

((( Y )))
	|
	|
+- -|- - - - - - - - - - - - -+        xxxxxxxxxxxx          +--------+
|+--+-----------+     +------+|       xxx         xxx        |        |
||              |     |      ||      xx  Internet   xx       |        |
|| Pico Cell GW |<----+ Host |<-----xx     or       xx------>|        |
|| STM32F401CD  | USB/|      ||      xx  Intranet   xx       | Server |
||   Sx1308     | UART+------+|       xxx         xxx        |        |
||  2*SX1257    |      Linux  |        xxxxxxxxxxxx          |        |
|+--------------+             |                              |        |
|                             |                              +--------+
|                             |
+- - - - - - - - - - - - - - -+

1.1. MAIN

The MAIN/ directory contains the main program that runs on the MCU, which launches the USB/UART commands interpreter to communicate with the Host.

1.2. CmdUSB

The CmdUSB/ directory contains the USB/UART command interpreter to handle the communication between the Host and the concentrator. It is a bridge to the HAL which communicates with the SX1308 through SPI.

1.3. usb_cdc

The STM32 USB CDC library modified for this reference design.

1.4. SX1308HAL

The LoRa concentrator Hardware Abstraction Layer C library to configure the hardware, send and receive packets.

2. Precompiled binaries


The bin/ directory contains the precompiled binary files in .hex or .dfu formats, for both USB and UART communication bridges. To load the binary file into the target MCU flash memory, you have to:

2.1. USB

  • Make the MCU enter DFU mode:

    • either press the BOOT0 button of the PicoCell GW while plugging it to the host USB port
    • or use the util_boot tool provided with the picoGW_hal repository.
  • Program the binary into the MCU flash memory:

    ex:

    dfu-util -a 0 -D pgw_fw_usb.dfu
    

    Note: you may have to use sudo depending on your priviledges.

  • Unplug/replug USB PicoCell GW to exit DFU mode.

2.2. UART

  • Make the MCU enter UART bootloader:

    • either press the BOOT0 button of the PicoCell GW while plugging it to the host USB port
    • or use the util_boot tool provided with the picoGW_hal repository.
  • Program the binary into the MCU flash memory:

    ex:

    stm32flash -b 115200 /dev/ttyS0 -v -w pgw_fw_uart.hex -g 0x0
    

3. Build the project


In order to compile the whole project, a Keil project is provided in the src/ directory. Open the pgw.uvproj file in Keil and rebuild all.

By default, it builds the project for using USB communication bridge. In order to use the UART instead, uncomment the following line in src/MAIN/board.h before building all the project.

#define USE_UART 1

After the compilation as succeeded, a Pgw.hex file is created in the bin/ directory. It is the file to be programmed in the MCU flash memory. Refer to section 2 of this document to get information for flashing. A DFU file can be created from this .hex file using the "Dfu file manager" tool provided by STmicroelectronics. www.st.com/resource/en/user_manual/cd00155676.pdf

4. User Guide


A detailed PicoCell GW user guide is available here

5. Changelog


v0.2.1

  • Added a delay in the MCU init procedure to ensure that HSE (32MHz external clock) input is selected before starting USB enumeration.
  • Reset the SX1257 radios to fix a potential bad POR (Power-On Reset) condition when there are no Schottky diodes placed on the SX1257 radios reset line.
  • Unify the USB VID/PID values between the Linux version and Windows (picoGW_UI tool) version.

v0.2.0

  • Reverted AGC firmware from version 5 back to version 4.
  • Updated MCU FW version to match with picoGW_hal

v0.1.1

  • Disabled USB vbus sensing
  • Moved delay to wait for COM bridge to be initialized in CMDMANAGER::Init().

v0.1.0

  • Code clean-up, refactoring
  • Support both USB and UART communication with host

v0.0.1

  • Initial release

6. Legal notice


The information presented in this project documentation does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified range.

SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER'S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise.

EOF

About

MCU driver/HAL for the Picocell Gateway concentrator board.

Resources

Stars

Watchers

Forks

Packages

No packages published

Languages