including additional stm32c0 cpu and board targets

boards/nucleo-c071rb/Kconfig

@@ -0,0 +1,17 @@
+# Copyright (C) 2024 BISSELL Homecare, Inc.
+#
+# This file is subject to the terms and conditions of the GNU Lesser
+# General Public License v2.1. See the file LICENSE in the top level
+# directory for more details.
+#
+
+config BOARD
+    default "nucleo-c071rb" if BOARD_NUCLEO_C031C6
+
+config BOARD_NUCLEO_C071RB
+    bool
+    default y
+    select BOARD_COMMON_NUCLEO64
+    select CPU_MODEL_STM32C071RB
+
+source "$(RIOTBOARD)/common/nucleo64/Kconfig"

boards/nucleo-c071rb/Makefile

@@ -0,0 +1,4 @@
+MODULE = board
+DIRS = $(RIOTBOARD)/common/nucleo
+
+include $(RIOTBASE)/Makefile.base

boards/nucleo-c071rb/Makefile.dep

@@ -0,0 +1 @@
+include $(RIOTBOARD)/common/nucleo64/Makefile.dep

boards/nucleo-c071rb/Makefile.features

@@ -0,0 +1,16 @@
+CPU = stm32
+CPU_MODEL = stm32c071rb
+
+# Put defined MCU peripherals here (in alphabetical order)
+FEATURES_PROVIDED += periph_adc
+FEATURES_PROVIDED += periph_i2c
+FEATURES_PROVIDED += periph_pwm
+FEATURES_PROVIDED += periph_spi
+FEATURES_PROVIDED += periph_timer
+FEATURES_PROVIDED += periph_uart
+
+# Put other features for this board (in alphabetical order)
+FEATURES_PROVIDED += riotboot
+
+# load the common Makefile.features for Nucleo boards
+include $(RIOTBOARD)/common/nucleo64/Makefile.features

boards/nucleo-c071rb/Makefile.include

@@ -0,0 +1,2 @@
+# load the common Makefile.include for Nucleo boards
+include $(RIOTBOARD)/common/nucleo64/Makefile.include

boards/nucleo-c071rb/doc.txt

@@ -0,0 +1,52 @@
+/**
+@defgroup    boards_nucleo-c071rb STM32 Nucleo-c071rb
+@ingroup     boards_common_nucleo64
+@brief       Support for the STM32 Nucleo-c071rb
+
+## Overview
+
+The Nucleo-c071rb is a board from ST's Nucleo family supporting a ARM
+Cortex-M0+ STM32C071RB microcontroller with 24KiB of RAM and 128KiB of Flash.
+
+## Pinout
+
+See Board Manual referenced below, section 7 pages 19-21.
+
+### MCU
+
+| MCU        | STM32c071rb         |
+|:---------- |:------------------- |
+| Family     | ARM Cortex-M0+      |
+| Vendor     | ST Microelectronics |
+| RAM        | 24KiB               |
+| Flash      | 128KiB              |
+| Frequency  | up to 48MHz         |
+| FPU        | no                  |
+| Timers     | 12 (2x watchdog, 1 SysTick, 5x 16-bit) |
+| ADCs       | 1x 12-bit (up to 19 channels) |
+| UARTs      |  2                  |
+| SPIs       |  1                  |
+| I2Cs       |  1                  |
+| RTC        |  1                  |
+| Vcc        |  2.0V - 3.6V        |
+| Datasheet  | [Datasheet](https://www.st.com/resource/en/datasheet/stm32c071rb.pdf) |
+| Reference Manual | [Reference Manual](https://www.st.com/resource/en/reference_manual/rm0490-stm32c0x1-advanced-armbased-32bit-mcus-stmicroelectronics.pdf) |
+| Programming Manual | [Programming Manual](https://www.st.com/resource/en/programming_manual/pm0223-stm32-cortexm0-mcus-programming-manual-stmicroelectronics.pdf) |
+| Board Manual   | [Board Manual](https://www.st.com/resource/en/user_manual/um3353-stm32-nucleo64-board-mb2046-stmicroelectronics.pdf) |
+
+## Flashing the Board Using ST-LINK Removable Media
+
+On-board ST-LINK programmer provides via composite USB device removable media.
+Copying the HEX file causes reprogramming of the board. This task
+could be performed manually; however, the cpy2remed (copy to removable
+media) PROGRAMMER script does this automatically. To program board in
+this manner, use the command:
+
+```
+make BOARD=nucleo-c071rb PROGRAMMER=cpy2remed flash
+```
+
+@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
+could be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
+
+ */

boards/nucleo-c071rb/include/periph_conf.h

@@ -0,0 +1,181 @@
+/*
+ * Copyright (C) 2024 BISSELL Homecare, Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License v2.1. See the file LICENSE in the top level
+ * directory for more details.
+ */
+
+/**
+ * @ingroup     boards_nucleo-c071rb
+ * @{
+ *
+ * @file
+ * @brief       Peripheral MCU configuration for the nucleo-c031c6 board
+ *
+ * @author      Jason Parker <[email protected]>
+ */
+
+#ifndef PERIPH_CONF_H
+#define PERIPH_CONF_H
+
+/* Add specific clock configuration (HSE, LSE) for this board here */
+#ifndef CONFIG_BOARD_HAS_LSE
+#define CONFIG_BOARD_HAS_LSE            1
+#endif
+
+#include "clk_conf.h"
+#include "cfg_i2c1_pb8_pb9.h"
+#include "cfg_rtt_default.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @name    Timer configuration
+ * @{
+ */
+static const timer_conf_t timer_config[] = {
+    {
+        .dev      = TIM3,
+        .max      = 0x0000ffff,
+        .rcc_mask = RCC_APBENR1_TIM3EN,
+        .bus      = APB1,
+        .irqn     = TIM3_IRQn
+    }
+};
+
+#define TIMER_0_ISR         isr_tim3
+
+#define TIMER_NUMOF         ARRAY_SIZE(timer_config)
+/** @} */
+
+/**
+ * @name    UART configuration
+ * @{
+ */
+static const uart_conf_t uart_config[] = {
+    {
+        .dev        = USART2,
+        .rcc_mask   = RCC_APBENR1_USART2EN,
+        .rx_pin     = GPIO_PIN(PORT_A, 3),
+        .tx_pin     = GPIO_PIN(PORT_A, 2),
+        .rx_af      = GPIO_AF1,
+        .tx_af      = GPIO_AF1,
+        .bus        = APB1,
+        .irqn       = USART2_IRQn,
+    },
+    {   /* Arduino pinout on D0/D1 */
+        .dev        = USART1,
+        .rcc_mask   = RCC_APBENR2_USART1EN,
+        .rx_pin     = GPIO_PIN(PORT_B, 7),
+        .tx_pin     = GPIO_PIN(PORT_B, 6),
+        .rx_af      = GPIO_AF0,
+        .tx_af      = GPIO_AF0,
+        .bus        = APB12, //?
+        .irqn       = USART1_IRQn,
+    },
+};
+
+#define UART_0_ISR          (isr_usart2)
+#define UART_1_ISR          (isr_usart1)
+
+#define UART_NUMOF          ARRAY_SIZE(uart_config)
+/** @} */
+
+/**
+ * @name    ADC configuration
+ *
+ * Note that we do not configure all ADC channels,
+ * and not in the STM32C071 order. Instead, we
+ * just define 6 ADC channels, for the Nucleo
+ * Arduino header pins A0-A5.
+ *
+ * To find appropriate device and channel find in the
+ * board manual, table showing pin assignments and
+ * information about ADC - a text similar to ARD_A[N]_IN[X],
+ * where:
+ * [N] - describes analog pin number,
+ * [X] - describes used channel - indexed from 1,
+ * for example ARD_A5_IN16 is channel 16
+ *
+ * For Nucleo-C071RB this information is in board manual
+ *
+ * STM32C031C6 do not have internal channel for VBAT, more details provided
+ * in the MCU datasheet - section 3.14, page 20.
+ *
+ * @{
+ */
+static const adc_conf_t adc_config[] = {
+    { .pin = GPIO_PIN(PORT_A,  0), .dev = 0, .chan =  0 }, /* ARD_A0_IN0  */
+    { .pin = GPIO_PIN(PORT_A,  1), .dev = 0, .chan =  1 }, /* ARD_A1_IN1  */
+    { .pin = GPIO_PIN(PORT_A,  4), .dev = 0, .chan =  4 }, /* ARD_A2_IN4  */
+    { .pin = GPIO_PIN(PORT_B,  1), .dev = 0, .chan = 18 }, /* ARD_A3_IN18 */
+    { .pin = GPIO_PIN(PORT_A, 11), .dev = 0, .chan = 11 }, /* ARD_A4_IN11 */
+    { .pin = GPIO_PIN(PORT_A, 12), .dev = 0, .chan = 12 }, /* ARD_A5_IN12 */
+};
+
+#define ADC_NUMOF           ARRAY_SIZE(adc_config)
+/** @} */
+
+/**
+ * @name    PWM configuration
+ * @{
+ *
+ * To find appriopate device and channel find in the MCU datasheet table
+ * concerning "Alternate function AF0 to AF7" a text similar to TIM[X]_CH[Y],
+ * where:
+ * TIM[X] - is device,
+ * [Y] - describes used channel (indexed from 0), for example TIM2_CH1 is
+ * channel 0 in configuration structure (cc_chan - field),
+ * Port column in the table describes connected port.
+ *
+ * For Nucleo-c071rb this information is in the MCU datasheet, Table 13, page 35.
+ *
+ */
+static const pwm_conf_t pwm_config[] = {
+    {
+        .dev      = TIM3,
+        .rcc_mask = RCC_APBENR1_TIM3EN,
+        .chan     = { { .pin = GPIO_PIN(PORT_B, 5) /*CN9  D6 */, .cc_chan = 1 },
+                      { .pin = GPIO_PIN(PORT_B, 0) /*CN5 D10 */, .cc_chan = 2 },
+                      { .pin = GPIO_PIN(PORT_B, 1) /*CN8  A3 */, .cc_chan = 3 },
+                      { .pin = GPIO_UNDEF,                       .cc_chan = 0 } },
+        .af       = GPIO_AF1,
+        .bus      = APB1
+    },
+};
+
+#define PWM_NUMOF           ARRAY_SIZE(pwm_config)
+/** @} */
+
+/**
+ * @name   SPI configuration
+ * @{
+ */
+static const spi_conf_t spi_config[] = {
+    {
+        .dev            = SPI1,
+        .mosi_pin       = GPIO_PIN(PORT_A, 7),  /* Arduino D11 */
+        .miso_pin       = GPIO_PIN(PORT_A, 6),  /* Arduino D12 */
+        .sclk_pin       = GPIO_PIN(PORT_A, 5),  /* Arduino D13 */
+        .cs_pin         = GPIO_UNDEF,
+        .mosi_af        = GPIO_AF0,
+        .miso_af        = GPIO_AF0,
+        .sclk_af        = GPIO_AF0,
+        .cs_af          = GPIO_AF0,
+        .rccmask        = RCC_APBENR2_SPI1EN,
+        .apbbus         = APB12,
+    },
+};
+
+#define SPI_NUMOF           ARRAY_SIZE(spi_config)
+/** @} */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* PERIPH_CONF_H */
+/** @} */

boards/stm32c0116-dk/Kconfig

@@ -0,0 +1,14 @@
+# Copyright (C) 2024 BISSELL Homecare, Inc.
+#
+# This file is subject to the terms and conditions of the GNU Lesser
+# General Public License v2.1. See the file LICENSE in the top level
+# directory for more details.
+#
+
+config BOARD
+    default "stm32c0116-dk" if BOARD_STM32C0116_DK
+
+config  BOARD_STM32C0116_DK
+    bool
+    default y
+    select CPU_MODEL_STM32C011F6

boards/stm32c0116-dk/Makefile

@@ -0,0 +1,3 @@
+MODULE = board
+
+include $(RIOTBASE)/Makefile.base

boards/stm32c0116-dk/Makefile.features

@@ -0,0 +1,9 @@
+CPU = stm32
+CPU_MODEL = stm32c011f6
+
+# Put defined MCU peripherals here (in alphabetical order)
+FEATURES_PROVIDED += periph_gpio
+FEATURES_PROVIDED += periph_rtc
+FEATURES_PROVIDED += periph_rtt
+FEATURES_PROVIDED += periph_timer
+FEATURES_PROVIDED += periph_uart

boards/stm32c0116-dk/Makefile.include

@@ -0,0 +1,18 @@
+# we use shared STM32 configuration snippets
+INCLUDES += -I$(RIOTBASE)/boards/common/stm32/include
+
+# define the default port depending on the host OS
+PORT_LINUX ?= /dev/ttyACM0
+PORT_DARWIN ?= $(firstword $(sort $(wildcard /dev/tty.SLAB_USBtoUART*)))
+
+# setup serial terminal
+include $(RIOTMAKE)/tools/serial.inc.mk
+
+PROGRAMMER ?= openocd
+OPENOCD_DEBUG_ADAPTER ?= stlink
+
+# openocd programmer is supported
+PROGRAMMERS_SUPPORTED += openocd
+
+# this board uses openocd
+include $(RIOTMAKE)/tools/openocd.inc.mk

boards/stm32c0116-dk/dist/openocd.cfg

@@ -0,0 +1,7 @@
+set WORKAREASIZE 0x2000
+source [find interface/stlink-v2.cfg]
+source [find target/stm32c0x.cfg]
+
+#reset_config srst_only
+
+#$_TARGETNAME configure -rtos auto

boards/stm32c0116-dk/doc.txt

@@ -0,0 +1,35 @@
+/**
+ * @defgroup    boards_stm32c0116-dk STM32C0116-DK
+ * @ingroup     boards
+ * @brief       Support for the STM32C0116-DK board.
+ *
+ * ### General information
+ *
+ * The ST [STM32C0116-DK](https://www.st.com/en/evaluation-tools/stm32c0116-dk.html)
+ * is an evaluation board supporting a ARM Cortex-M0 STM32C011F6 microcontroller
+ * with 8KB of RAM and 32KB of ROM Flash.
+ *
+ * ### Pinout
+ *
+ * See [this application note as reference](https://www.st.com/resource/en/application_note/an5673-getting-started-with-stm32c0-mcu-hardware-development-stmicroelectronics.pdf).
+ * This means the responsibility is on the firmware configurer to take special care when configured IO, ensuring that
+ * ports are not conflicting on each pin.
+ *
+ * ### Flash the board
+ *
+ * The STM32C0116-DK board includes an on-board ST-LINK programmer and can be
+ * flashed using OpenOCD.
+ *
+ * To flash this board, just use the following command:
+ *
+ * ```
+ * make BOARD=stm32c0116-dk flash -C examples/hello-world
+ * ```
+ *
+ * ### UART Terminal Interaction
+ *
+ * Due to the limited number of pins, to get stdio UART traffic, use a USB->UART adapter
+ * like the CP2104 from Adafruit (http://adafru.it/954).  Connect the adapter's TX line
+ * to the MCU RX pin (PB6, Pin 8) and the adapter's RX line to the MCU's TX pin -
+ * (PB7, pin 1)
+ */