binc is a BINary Calculator with REPL user interface.
User can set a number to binc's inner buffer via REPL interpreter or command line arguments to perform arithmetic operations on that number. Been launched in interactive mode binc prints the number stored in buffer in binary format and reads commands from standard input to be executed upon whole buffer or particular bits of buffer.
Or it reads commands from command line argument and prints the result.
There is binc's output with 42 assigned to buffer.
$ binc # shell's prompt and command line
#
0x2a 0d42 0o52 # number representation in different radixes
31 24 23 16 15 8 7 0 # bit indexes
+ 0000 0000 0000 0000 0000 0000 0010 1010 # the number in binary radix written to the buffer
0 28 27 20 19 12 11 4 3 # bit indexes
(binc) # binc's prompt for commands
"bit indexes" intended to help user to understand what index each bit has. "the number in binary radix" is split into bytes and half-bytes sequences of bits.
On the line called "the number in binary radix" there is a '+' at the beginning,
it represents that the number is positive, - represents a negative number.
The ' 0' under the '+' is value of "carry bit". Carry bit indicates whether an overflow occurred after arithmetic operation.
To run binc in non-interactive mode run it with key -e and pass a list of binc's commands separated by ;, see examples.
Command syntax is:
- X operator Y
- operator X
- command
, where X is lvalue, it must be only a range; Y is rvalue operand, it can be a number or range;
operator is some arithmetic operation, like >> or +; command is one of reserved words.
While paring commands all spaces are ignored like in Fortran
number is a numeric literal with prefixes 0x, 0d, 0b, 0h(0x) to specify corresponding radix.
It can be prefixed with minus to make it negative.
First operand X may be omitted, by default it is range [] - the whole buffer,
range [i:j] - bits from j to i, j <= i, range [n] operates on exactly nth bit.
Half-range [i:] means from ith bit inclusive to the lowest bit, [:i] means from the
highest bit to the ith bit inclusive. The Y operand also can be a character surrounded by single quotes,
like 'x', unicode is supported, but emoji aren't. To input ' type '''.
If operator is omitted, binc do assignment = operation by default. To omit an operator,
X also must be omitted. Only Y operand is necessary. If one typed just 123 without specifying an operator,
the number 123 will be set to the buffer.
Empty command line performs repetition of the last command.
binc knows help command with no arguments, which will print all possible commands, operators and syntax tips.
To quit binc press [CTRL+C], [CTRL+D] or [CTRL+Q].
| operator | description | operator | description |
|---|---|---|---|
= |
assignment | == |
comparison, only prints result |
+ |
add | >> |
signed shift right, 1000 >> 1 is 1100 |
- |
subtract | >>> |
unsigned shift right (1000 >>> 1 == 0100 |
* |
multiply | << |
shift left |
/ |
divide | > |
greater, only prints result |
% |
remainder | < |
less, only prints result |
^ |
bitwise xor | ~>> |
signed cyclic shift right |
& |
bitwise and | <<~ |
cyclic shift left |
| | | bitwise or | pow |
exponentiation |
<> |
exchange | root |
square root |
| operator | description | operator | description |
|---|---|---|---|
~ |
bitwise not | ! |
arithmetic negation |
shf |
shuffle bits | rnd |
randomize |
rev |
reverse |
| command | action |
|---|---|
help |
prints all operators, commands and syntactic tips |
undo |
undo last operation |
reduo |
redo operation, that was "undo"ed |
intX |
treat buffer as an integer, X - bits: 8, 16, 32, 64, 128. |
floatX |
treat buffer as a floating point one, X - bits. (not ready) |
fixedX |
treat buffer as a fixed point one, X - bits. (not ready) |
printf |
prints buffer in a specified format. (not ready) |
signed |
treat buffer as singed int (bit width does not change) |
unsigned |
treat buffer as unsigned int (bit width does not change) |
(binc) 42 sets number 42 to the buffer.
(binc) +1 add 1 to the value of buffer.
(binc) -1 set all bits to 1 if number was 0. Actually subtracts -1.
(binc) &0 bitwise conjunction of bits of the buffer and 0, set all bits to 0.
(binc) /2;>>1 divides buffer's value by 2 and shifts right one bit.
(binc) [31]=1 set 31st bit of the buffer to 1, the number in buffer becomes negative.
(binc) [31:24] cnt 0 count zero bits in range from 24th bit to 31st bit inclusive.
(binc) [15:4] printf x prints bits from 4 to 15 inclusive as hexadecimal (not ready).
(binc) [15:0] <> [31:16] swap values of lower and higher bits of the buffer.
(binc) '愛' set a kanji code to the buffer.
(binc) ! do arithmetic negation on the buffer. X becomes -X.
$ binc -e '-1;[7:0]&0' sets negative number (all bits become 1), than zeroes first byte, prints.
$ binc -e '123' -fx initialize with 123, print as hexadecimal.
$ binc -e '123' -p initialize with 123, print as binary with 32 digits, padded from left with zeroes.
Install Rust, compile and run:
cargo build --release
cargo run- binc is colored
- It is possible to make binc to print logs by passing flag -v in command line.
To report a bug please do
binc -vvvv -e '...'with commands which caused a bug, and copy output to the issues of the repo. - Set history size by passing --history=X in command line, where X is a desired history length.
- An attempt to set a negative number to the buffer with command
$ binc -e -- '-1'won't work.
