Updated extruder tuning, max brightness on messages and more (#982)

bigtreetech · Aug 19, 2020 · 47bcaee · 47bcaee
1 parent 420d631
commit 47bcaee
Show file tree

Hide file tree

Showing 32 changed files with 636 additions and 29 deletions.
diff --git a/.gitignore b/.gitignore
@@ -119,4 +119,4 @@ cmake-build-*
 .cproject
 .pydevproject
 .settings
-.classpath
+.classpath
diff --git a/TFT/src/User/API/Language/Language.c b/TFT/src/User/API/Language/Language.c
@@ -143,7 +143,7 @@ const char *const tc_pack[LABEL_NUM] = {
   #undef  X_WORD
 };
 
-uint8_t *textSelect(uint8_t sel)
+uint8_t *textSelect(uint16_t sel)
 {
   switch(infoSettings.language)
   {

diff --git a/TFT/src/User/API/Language/Language.h b/TFT/src/User/API/Language/Language.h
@@ -44,6 +44,6 @@ enum {
   LABEL_CUSTOM_VALUE,
 };
 
-uint8_t * textSelect(uint8_t sel);
+uint8_t * textSelect(uint16_t sel);
 
 #endif
diff --git a/TFT/src/User/API/Language/Language.inc b/TFT/src/User/API/Language/Language.inc
@@ -252,5 +252,16 @@ X_WORD (PID_TITLE)
 X_WORD (PID_START_INFO)
 X_WORD (PID_START_INFO_2)
 X_WORD (PID_START_INFO_3)
-X_WORD (EXTRUDE_100)
+X_WORD (TUNE_EXTRUDER)
+X_WORD (TUNE_EXT_EXTRUDE_100)
+X_WORD (TUNE_EXT_TEMP)
+X_WORD (TUNE_EXT_TEMPLOW)
+X_WORD (TUNE_EXT_DESIREDVAL)
+X_WORD (TUNE_EXT_MARK120MM)
+X_WORD (TUNE_EXT_HEATOFF)
+X_WORD (TUNE_EXT_ADJ_ESTEPS)
+X_WORD (TUNE_EXT_ESTEPS_SAVED)
+X_WORD (TUNE_EXT_MEASURED)
+X_WORD (TUNE_EXT_OLD_ESTEP)
+X_WORD (TUNE_EXT_NEW_ESTEP)
 X_WORD (CONNECTION_SETTINGS)
diff --git a/TFT/src/User/API/Language/language_am.h b/TFT/src/User/API/Language/language_am.h
@@ -247,7 +247,18 @@
     #define AM_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define AM_PID_START_INFO_2       "PID autotune in progress!"
     #define AM_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define AM_EXTRUDE_100            "Ext. 100mm"
+    #define AM_TUNE_EXTRUDER          "Tune steps"
+    #define AM_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define AM_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define AM_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define AM_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define AM_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define AM_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define AM_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define AM_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define AM_TUNE_EXT_MEASURED      "Length remaining:"
+    #define AM_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define AM_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define AM_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_ca.h b/TFT/src/User/API/Language/language_ca.h
@@ -247,7 +247,18 @@
     #define CA_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define CA_PID_START_INFO_2       "PID autotune in progress!"
     #define CA_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define CA_EXTRUDE_100            "Ext. 100mm"
+    #define CA_TUNE_EXTRUDER          "Tune steps"
+    #define CA_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define CA_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define CA_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define CA_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define CA_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define CA_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define CA_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define CA_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define CA_TUNE_EXT_MEASURED      "Length remaining:"
+    #define CA_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define CA_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define CA_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_cn.h b/TFT/src/User/API/Language/language_cn.h
@@ -247,7 +247,18 @@
     #define CN_PID_START_INFO         "开始PID自动整定,需要几分钟来完成,是否继续?"
     #define CN_PID_START_INFO_2       "PID 正在自动整定中!"
     #define CN_PID_START_INFO_3       "不要操作触控屏直到整定完成!"
-    #define CN_EXTRUDE_100            "挤出100mm"
+    #define CN_TUNE_EXTRUDER          "Tune steps"
+    #define CN_TUNE_EXT_EXTRUDE_100   "挤出100mm"
+    #define CN_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define CN_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define CN_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define CN_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define CN_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define CN_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define CN_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define CN_TUNE_EXT_MEASURED      "Length remaining:"
+    #define CN_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define CN_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define CN_CONNECTION_SETTINGS    "连接"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_cz.h b/TFT/src/User/API/Language/language_cz.h
@@ -247,7 +247,18 @@
     #define CZ_PID_START_INFO         "PID autokalibrace bude spuštěna.\n Bude to cvíli trvat. Pokračovat?"
     #define CZ_PID_START_INFO_2       "PID autokalibrace probíhá!"
     #define CZ_PID_START_INFO_3       "NEDOTÝKEJ se displeje dokud není dokončeno\n (Zelená LED svítí)!"
-    #define CZ_EXTRUDE_100            "100mm Vysunutí"
+    #define CZ_TUNE_EXTRUDER          "Tune steps"
+    #define CZ_TUNE_EXT_EXTRUDE_100   "100mm Vysunutí"
+    #define CZ_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define CZ_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define CZ_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define CZ_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define CZ_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define CZ_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define CZ_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define CZ_TUNE_EXT_MEASURED      "Length remaining:"
+    #define CZ_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define CZ_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define CZ_CONNECTION_SETTINGS    "Připojení"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_de.h b/TFT/src/User/API/Language/language_de.h
@@ -247,7 +247,18 @@
     #define DE_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define DE_PID_START_INFO_2       "PID autotune in progress!"
     #define DE_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define DE_EXTRUDE_100            "Ext. 100mm"
+    #define DE_TUNE_EXTRUDER          "Tune steps"
+    #define DE_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define DE_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define DE_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define DE_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define DE_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define DE_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define DE_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define DE_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define DE_TUNE_EXT_MEASURED      "Length remaining:"
+    #define DE_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define DE_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define DE_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_du.h b/TFT/src/User/API/Language/language_du.h
@@ -247,7 +247,18 @@
     #define DU_PID_START_INFO         "PID autotune zal starten.\nDit kan een paar minuten duren.\nDoorgaan?"
     #define DU_PID_START_INFO_2       "PID autotune is bezig!"
     #define DU_PID_START_INFO_3       "Raak het scherm NIET aan totdat deze klaar is (groene LED aan)!"
-    #define DU_EXTRUDE_100            "Ext. 100mm"
+    #define DU_TUNE_EXTRUDER          "Tune steps"
+    #define DU_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define DU_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define DU_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define DU_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define DU_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define DU_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define DU_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define DU_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define DU_TUNE_EXT_MEASURED      "Length remaining:"
+    #define DU_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define DU_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define DU_CONNECTION_SETTINGS    "Connecties"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_en.h b/TFT/src/User/API/Language/language_en.h
@@ -247,7 +247,18 @@
     #define EN_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define EN_PID_START_INFO_2       "PID autotune in progress!"
     #define EN_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define EN_EXTRUDE_100            "Ext. 100mm"
+    #define EN_TUNE_EXTRUDER          "Tune steps"
+    #define EN_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define EN_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define EN_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define EN_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define EN_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define EN_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define EN_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define EN_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define EN_TUNE_EXT_MEASURED      "Length remaining:"
+    #define EN_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define EN_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define EN_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_es.h b/TFT/src/User/API/Language/language_es.h
@@ -247,7 +247,18 @@
     #define ES_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define ES_PID_START_INFO_2       "PID autotune in progress!"
     #define ES_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define ES_EXTRUDE_100            "Ext. 100mm"
+    #define ES_TUNE_EXTRUDER          "Tune steps"
+    #define ES_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define ES_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define ES_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define ES_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define ES_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define ES_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define ES_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define ES_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define ES_TUNE_EXT_MEASURED      "Length remaining:"
+    #define ES_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define ES_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define ES_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_fr.h b/TFT/src/User/API/Language/language_fr.h
@@ -247,7 +247,18 @@
     #define FR_PID_START_INFO         "L'autocalibrage PID va être\nlancé. Cela peut prendre\nquelques minutes. Continuer ?"
     #define FR_PID_START_INFO_2       "Autocalibrage PID en cours !"
     #define FR_PID_START_INFO_3       "Ne touchez pas l'écran avant la fin (LED verte allumée) !"
-    #define FR_EXTRUDE_100            "Ext. 100mm"
+    #define FR_TUNE_EXTRUDER          "Tune steps"
+    #define FR_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define FR_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define FR_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define FR_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define FR_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define FR_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define FR_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define FR_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define FR_TUNE_EXT_MEASURED      "Length remaining:"
+    #define FR_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define FR_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define FR_CONNECTION_SETTINGS    "Connexion"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_gr.h b/TFT/src/User/API/Language/language_gr.h
@@ -247,7 +247,18 @@
     #define GR_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define GR_PID_START_INFO_2       "PID autotune in progress!"
     #define GR_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define GR_EXTRUDE_100            "Ext. 100mm"
+    #define GR_TUNE_EXTRUDER          "Tune steps"
+    #define GR_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define GR_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define GR_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define GR_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define GR_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define GR_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define GR_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define GR_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define GR_TUNE_EXT_MEASURED      "Length remaining:"
+    #define GR_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define GR_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define GR_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_hu.h b/TFT/src/User/API/Language/language_hu.h
@@ -247,7 +247,18 @@
     #define HU_PID_START_INFO         "A PID önhangolása elindul.\nPercekig is eltarthat.\nFolytatod?"
     #define HU_PID_START_INFO_2       "PID Automatikus hangolása zajlik!"
     #define HU_PID_START_INFO_3       "NE ÉRINTSD meg a kijelzőt míg nincs kész! (zöld LED jelzi)!"
-    #define HU_EXTRUDE_100            "Kiad 100mm"
+    #define HU_TUNE_EXTRUDER          "Tune steps"
+    #define HU_TUNE_EXT_EXTRUDE_100   "Kiad 100mm"
+    #define HU_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define HU_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define HU_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define HU_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define HU_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define HU_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define HU_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define HU_TUNE_EXT_MEASURED      "Length remaining:"
+    #define HU_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define HU_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define HU_CONNECTION_SETTINGS    "Kapcsolat"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_it.h b/TFT/src/User/API/Language/language_it.h
@@ -247,7 +247,18 @@
     #define IT_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define IT_PID_START_INFO_2       "PID autotune in progress!"
     #define IT_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define IT_EXTRUDE_100            "Ext. 100mm"
+    #define IT_TUNE_EXTRUDER          "Tune steps"
+    #define IT_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define IT_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define IT_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define IT_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define IT_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define IT_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define IT_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define IT_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define IT_TUNE_EXT_MEASURED      "Length remaining:"
+    #define IT_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define IT_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define IT_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_jp.h b/TFT/src/User/API/Language/language_jp.h
@@ -247,7 +247,18 @@
     #define JP_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define JP_PID_START_INFO_2       "PID autotune in progress!"
     #define JP_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define JP_EXTRUDE_100            "Ext. 100mm"
+    #define JP_TUNE_EXTRUDER          "Tune steps"
+    #define JP_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define JP_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define JP_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define JP_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define JP_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define JP_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define JP_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define JP_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define JP_TUNE_EXT_MEASURED      "Length remaining:"
+    #define JP_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define JP_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define JP_CONNECTION_SETTINGS    "Connection"
 
 #endif
diff --git a/TFT/src/User/API/Language/language_pl.h b/TFT/src/User/API/Language/language_pl.h
@@ -247,7 +247,18 @@
     #define PL_PID_START_INFO         "PID autotune may take\nsome time to complete.\nContinue?"
     #define PL_PID_START_INFO_2       "PID autotune in progress!"
     #define PL_PID_START_INFO_3       "Do not touch the screen until completed (green LED ON)!"
-    #define PL_EXTRUDE_100            "Ext. 100mm"
+    #define PL_TUNE_EXTRUDER          "Tune steps"
+    #define PL_TUNE_EXT_EXTRUDE_100   "Ext. 100mm"
+    #define PL_TUNE_EXT_TEMP          "Extruder tuning | Heat"
+    #define PL_TUNE_EXT_TEMPLOW       "Desired temperature too low!\nMinimum temperature: %d C"
+    #define PL_TUNE_EXT_DESIREDVAL    "Temperature is not yet at the desired value"
+    #define PL_TUNE_EXT_MARK120MM     "Mark 120 mm on your fillament\nPress '%s' when ready\nMeasure remaining length\nafter extruding"
+    #define PL_TUNE_EXT_HEATOFF       "Turn the heater off?"
+    #define PL_TUNE_EXT_ADJ_ESTEPS    "Adjust E-Steps"
+    #define PL_TUNE_EXT_ESTEPS_SAVED  "New E-steps saved!\nDon't forget to\nsave it in EEPROM\nNew value: %0.2f"
+    #define PL_TUNE_EXT_MEASURED      "Length remaining:"
+    #define PL_TUNE_EXT_OLD_ESTEP     "Old e-steps: %0.2f"
+    #define PL_TUNE_EXT_NEW_ESTEP     "New e-steps: %0.2f"
     #define PL_CONNECTION_SETTINGS    "Connection"
 
 #endif