forked from openwrt/openwrt
-
Notifications
You must be signed in to change notification settings - Fork 1
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <[email protected]>
(cherry picked from commit b800e3d)- Loading branch information
1 parent
df3f500
commit 2acff7f
Showing
7 changed files
with
315 additions
and
9 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,263 @@ | ||
| // SPDX-License-Identifier: (GPL-2.0 OR MIT) | ||
|
|
||
| /dts-v1/; | ||
| #include <dt-bindings/input/input.h> | ||
| #include <dt-bindings/gpio/gpio.h> | ||
| #include <dt-bindings/leds/common.h> | ||
|
|
||
| #include "mt7986a.dtsi" | ||
|
|
||
| / { | ||
|
|
||
| model = "ASUS RT-AX59U"; | ||
| compatible = "asus,rt-ax59u", "mediatek,mt7986a"; | ||
|
|
||
| aliases { | ||
| serial0 = &uart0; | ||
| led-boot = &led_status_green; | ||
| led-failsafe = &led_status_red; | ||
| led-running = &led_status_green; | ||
| led-upgrade = &led_status_blue; | ||
| }; | ||
|
|
||
| chosen { | ||
| stdout-path = "serial0:115200n8"; | ||
| bootargs-override = "ubi.mtd=UBI_DEV"; | ||
| }; | ||
|
|
||
| memory { | ||
| reg = <0 0x40000000 0 0x20000000>; | ||
| }; | ||
|
|
||
| keys { | ||
| compatible = "gpio-keys"; | ||
|
|
||
| button-0 { | ||
| label = "wps"; | ||
| gpios = <&pio 9 GPIO_ACTIVE_LOW>; | ||
| linux,code = <KEY_WPS_BUTTON>; | ||
| }; | ||
|
|
||
| button-1 { | ||
| label = "reset"; | ||
| gpios = <&pio 10 GPIO_ACTIVE_LOW>; | ||
| linux,code = <KEY_RESTART>; | ||
| }; | ||
| }; | ||
|
|
||
| leds { | ||
| compatible = "gpio-leds"; | ||
|
|
||
| led_status_green: led-0 { | ||
| color = <LED_COLOR_ID_GREEN>; | ||
| function = LED_FUNCTION_STATUS; | ||
| gpios = <&pio 11 GPIO_ACTIVE_LOW>; | ||
| }; | ||
|
|
||
| led_status_red: led-1 { | ||
| color = <LED_COLOR_ID_RED>; | ||
| function = LED_FUNCTION_STATUS; | ||
| gpios = <&pio 12 GPIO_ACTIVE_LOW>; | ||
| }; | ||
|
|
||
| led_status_blue: led-2 { | ||
| color = <LED_COLOR_ID_BLUE>; | ||
| function = LED_FUNCTION_STATUS; | ||
| gpios = <&pio 13 GPIO_ACTIVE_LOW>; | ||
| }; | ||
| }; | ||
|
|
||
| gpio-export { | ||
| compatible = "gpio-export"; | ||
|
|
||
| out { | ||
| gpio-export,name = "led-light"; | ||
| gpio-export,output = <0>; | ||
| gpios = <&pio 22 GPIO_ACTIVE_LOW>; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &crypto { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| ð { | ||
| status = "okay"; | ||
|
|
||
| gmac0: mac@0 { | ||
| /* LAN */ | ||
| compatible = "mediatek,eth-mac"; | ||
| reg = <0>; | ||
| phy-mode = "2500base-x"; | ||
|
|
||
| fixed-link { | ||
| speed = <2500>; | ||
| full-duplex; | ||
| pause; | ||
| }; | ||
| }; | ||
|
|
||
| mdio: mdio-bus { | ||
| #address-cells = <1>; | ||
| #size-cells = <0>; | ||
|
|
||
| switch@1f { | ||
| compatible = "mediatek,mt7531"; | ||
| reg = <31>; | ||
| reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; | ||
|
|
||
| ports { | ||
| #address-cells = <1>; | ||
| #size-cells = <0>; | ||
|
|
||
| port@1 { | ||
| reg = <1>; | ||
| label = "wan"; | ||
| }; | ||
|
|
||
| port@2 { | ||
| reg = <2>; | ||
| label = "lan1"; | ||
| }; | ||
|
|
||
| port@3 { | ||
| reg = <3>; | ||
| label = "lan2"; | ||
| }; | ||
|
|
||
| port@4 { | ||
| reg = <4>; | ||
| label = "lan3"; | ||
| }; | ||
|
|
||
| port@6 { | ||
| reg = <6>; | ||
| label = "cpu"; | ||
| ethernet = <&gmac0>; | ||
| phy-mode = "2500base-x"; | ||
|
|
||
| fixed-link { | ||
| speed = <2500>; | ||
| full-duplex; | ||
| pause; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &pio { | ||
| spi_flash_pins: spi-flash-pins-33-to-38 { | ||
| mux { | ||
| function = "spi"; | ||
| groups = "spi0", "spi0_wp_hold"; | ||
| }; | ||
| conf-pu { | ||
| pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; | ||
| drive-strength = <8>; | ||
| mediatek,pull-up-adv = <0>; /* bias-disable */ | ||
| }; | ||
| conf-pd { | ||
| pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; | ||
| drive-strength = <8>; | ||
| mediatek,pull-down-adv = <0>; /* bias-disable */ | ||
| }; | ||
| }; | ||
|
|
||
| wf_2g_5g_pins: wf_2g_5g-pins { | ||
| mux { | ||
| function = "wifi"; | ||
| groups = "wf_2g", "wf_5g"; | ||
| }; | ||
| conf { | ||
| pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", | ||
| "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", | ||
| "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", | ||
| "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", | ||
| "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", | ||
| "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", | ||
| "WF1_TOP_CLK", "WF1_TOP_DATA"; | ||
| drive-strength = <4>; | ||
| }; | ||
| }; | ||
|
|
||
| wf_dbdc_pins: wf-dbdc-pins { | ||
| mux { | ||
| function = "wifi"; | ||
| groups = "wf_dbdc"; | ||
| }; | ||
| conf { | ||
| pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", | ||
| "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", | ||
| "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", | ||
| "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", | ||
| "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", | ||
| "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", | ||
| "WF1_TOP_CLK", "WF1_TOP_DATA"; | ||
| drive-strength = <4>; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &spi0 { | ||
| pinctrl-names = "default"; | ||
| pinctrl-0 = <&spi_flash_pins>; | ||
| status = "okay"; | ||
|
|
||
| spi_nand: spi_nand@0 { | ||
| compatible = "spi-nand"; | ||
| #address-cells = <1>; | ||
| #size-cells = <1>; | ||
| reg = <0>; | ||
|
|
||
| spi-max-frequency = <20000000>; | ||
| spi-tx-buswidth = <4>; | ||
| spi-rx-buswidth = <4>; | ||
|
|
||
| partitions: partitions { | ||
| compatible = "fixed-partitions"; | ||
| #address-cells = <1>; | ||
| #size-cells = <1>; | ||
|
|
||
| partition@0 { | ||
| label = "u-boot"; | ||
| reg = <0x0 0x400000>; | ||
| read-only; | ||
| }; | ||
|
|
||
| partition@400000 { | ||
| label = "UBI_DEV"; | ||
| reg = <0x400000 0x7c00000>; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &watchdog { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &wifi { | ||
| status = "okay"; | ||
| pinctrl-names = "default", "dbdc"; | ||
| pinctrl-0 = <&wf_2g_5g_pins>; | ||
| pinctrl-1 = <&wf_dbdc_pins>; | ||
| }; | ||
|
|
||
| &trng { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &uart0 { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &ssusb { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &usb_phy { | ||
| status = "okay"; | ||
| }; |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters