forked from openwrt/openwrt
-
Notifications
You must be signed in to change notification settings - Fork 1
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
qualcommax: ipq807x: add support for Netgear WAX630
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi [email protected]:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <[email protected]>
Signed-off-by: Kristian Skramstad <[email protected]>- Loading branch information
Showing
7 changed files
with
290 additions
and
2 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
253 changes: 253 additions & 0 deletions
253
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,253 @@ | ||
| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT | ||
|
|
||
| /dts-v1/; | ||
|
|
||
| #include "ipq8074.dtsi" | ||
| #include "ipq8074-hk-cpu.dtsi" | ||
| #include "ipq8074-ess.dtsi" | ||
| #include <dt-bindings/input/input.h> | ||
| #include <dt-bindings/gpio/gpio.h> | ||
| #include <dt-bindings/leds/common.h> | ||
|
|
||
| / { | ||
| model = "Netgear WAX630"; | ||
| compatible = "netgear,wax630", "qcom,ipq8074"; | ||
|
|
||
| aliases { | ||
| serial0 = &blsp1_uart5; | ||
|
|
||
| ethernet0 = &dp6_syn; | ||
| ethernet1 = &dp4; | ||
| label-mac-device = &dp6_syn; | ||
|
|
||
| led-boot = &led_system_blue; | ||
| led-failsafe = &led_system_red; | ||
| led-running = &led_system_green; | ||
| led-upgrade = &led_system_blue; | ||
| }; | ||
|
|
||
| chosen { | ||
| stdout-path = "serial0:115200n8"; | ||
| bootargs-append = " root=/dev/ubiblock0_1"; | ||
| }; | ||
|
|
||
| keys { | ||
| compatible = "gpio-keys"; | ||
|
|
||
| reset { | ||
| label = "reset"; | ||
| gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; | ||
| linux,code = <KEY_RESTART>; | ||
| }; | ||
| }; | ||
|
|
||
| led-spi { | ||
| compatible = "spi-gpio"; | ||
| #address-cells = <1>; | ||
| #size-cells = <0>; | ||
|
|
||
| sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>; | ||
| mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>; | ||
|
|
||
| led_gpio: led-gpio@0 { | ||
| compatible = "fairchild,74hc595"; | ||
| reg = <0>; | ||
| gpio-controller; | ||
| #gpio-cells = <2>; | ||
| registers-number = <1>; | ||
| enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; | ||
| spi-max-frequency = <1000000>; | ||
| }; | ||
| }; | ||
|
|
||
| leds { | ||
| compatible = "gpio-leds"; | ||
|
|
||
| led_system_red: system-red { | ||
| label = "system:red"; | ||
| gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| led_system_green: system-green { | ||
| label = "system:green"; | ||
| gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| led_system_blue: system-blue { | ||
| label = "system:blue"; | ||
| gpios = <&tlmm 21 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| lan1-green { | ||
| label = "lan1:green"; | ||
| gpios = <&tlmm 26 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| lan1-orange { | ||
| label = "lan1:orange"; | ||
| gpios = <&tlmm 27 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| lan2-green { | ||
| label = "lan2:green"; | ||
| gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| lan2-orange { | ||
| label = "lan2:orange"; | ||
| gpios = <&tlmm 60 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 2g-blue { | ||
| label = "wlan2g:blue"; | ||
| gpios = <&tlmm 29 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 2g-green { | ||
| label = "wlan2g:green"; | ||
| gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 5g-low-blue { | ||
| label = "wlan5g_low:blue"; | ||
| gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 5g-low-green { | ||
| label = "wlan5g_low:green"; | ||
| gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 5g-high-blue { | ||
| label = "wlan5g_high:blue"; | ||
| gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| 5g-high-green { | ||
| label = "wlan5g_high:green"; | ||
| gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; | ||
| default-state = "off"; | ||
| }; | ||
|
|
||
| }; | ||
| }; | ||
|
|
||
| &edma { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &switch { | ||
| status = "okay"; | ||
|
|
||
| switch_cpu_bmp = <0x01>; | ||
| switch_lan_bmp = <0x3e>; | ||
| switch_wan_bmp = <0x40>; | ||
| switch_mac_mode = <0x00>; | ||
| switch_mac_mode1 = <0xff>; | ||
| switch_mac_mode2 = <0x0d>; | ||
| bm_tick_mode = <0x00>; | ||
| tm_tick_mode = <0x00>; | ||
|
|
||
| qcom,port_phyinfo { | ||
| port@3 { | ||
| port_id = <4>; | ||
| phy_address = <3>; | ||
| }; | ||
|
|
||
| port@5 { | ||
| port_id = <6>; | ||
| phy_address = <28>; | ||
| port_mac_sel = "QGMAC_PORT"; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &tlmm { | ||
| mdio_pins: mdio-pins { | ||
| mdc { | ||
| pins = "gpio68"; | ||
| function = "mdc"; | ||
| drive-strength = <8>; | ||
| bias-pull-up; | ||
| }; | ||
|
|
||
| mdio { | ||
| pins = "gpio69"; | ||
| function = "mdio"; | ||
| drive-strength = <8>; | ||
| bias-pull-up; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &mdio { | ||
| status = "okay"; | ||
|
|
||
| pinctrl-0 = <&mdio_pins>; | ||
| pinctrl-names = "default"; | ||
| reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; | ||
|
|
||
| qca8075: ethernet-phy@3 { | ||
| compatible = "ethernet-phy-ieee802.3-c22"; | ||
| reg = <3>; | ||
| }; | ||
|
|
||
| qca8081: ethernet-phy@28 { | ||
| compatible = "ethernet-phy-id004d.d101"; | ||
| reg = <28>; | ||
| reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>; | ||
| }; | ||
| }; | ||
|
|
||
| &dp4 { | ||
| status = "okay"; | ||
| phy-handle = <&qca8075>; | ||
| label = "lan2"; | ||
| }; | ||
|
|
||
| &dp6_syn { | ||
| status = "okay"; | ||
| phy-handle = <&qca8081>; | ||
| label = "lan1"; | ||
| }; | ||
|
|
||
| &qpic_bam { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &qpic_nand { | ||
| status = "okay"; | ||
|
|
||
| nand@0 { | ||
| reg = <0>; | ||
| nand-ecc-strength = <4>; | ||
| nand-ecc-step-size = <512>; | ||
| nand-bus-width = <8>; | ||
|
|
||
| partitions { | ||
| compatible = "qcom,smem-part"; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &blsp1_uart5 { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &wifi { | ||
| status = "okay"; | ||
|
|
||
| qcom,ath11k-calibration-variant = "Netgear-WAX630"; | ||
| }; |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters