This repository is a clone of tbs/linux_media. It contains patches for the following drivers
- stid135: ts6909x and tbs6903x cards (v1 and v2)
- stv091x: tbs5927 tbs6908 tbs6903 tbs6983 tbs6522 tbs6983 tbs6903 tbs6909
- tas2101: tbs5990, tbs6904
- si2183 based cards: tbs6504, tbs5580, tbs6916
- m88rs6060 based cards: tbs6902SE and tbs904SE. On these cards there is not IQ-scan (constellation display) to support blindscan, to fix bugs and to make improvements.
First install the required compilers, git ... You may also need libproc-processtable-perl (e.g., on ubuntu)
mkdir ~/blindscan_kernel
cd ~/blindscan_kernel
Check out the actual drivers. This uses the default branch which is called deepthought
git clone --depth=1 https://github.com/deeptho/linux_media.git ./media
Then check out a copy of DeepThought's media_build (try tbs media_build if it does not work)
git clone https://github.com/deeptho/neumo_media_build
Make sure software for kernel compilation is installed. For instance on fedora:
sudo dnf install -y patchutils
sudo dnf install -y ccache
sudo dnf install -y kernel-devel-`uname -r`
sudo dnf install -y perl-File-Copy #not needed?
sudo dnf install -y perl
sudo dnf install -y perl-Proc-ProcessTable
cd neumo_media_build
git checkout deepthought
git reset --hard
make dir DIR=../media
make distclean
./install.sh
Last but not least, install rsyslog so that kernel debug messages are stored in the file system in /var/log/debug:
sudo dnf install -y rsyslog
sudo vi /etc/rsyslog.conf # add "kern.debug /var/log/debug" line
sudo systemctl enable rsyslog
sudo systemctl start rsyslog #to have log messages in /var/log/debug
Now install the firmware (if needed):
wget http://www.tbsdtv.com/download/document/linux/tbs-tuner-firmwares_v1.0.tar.bz2
sudo tar jxvf tbs-tuner-firmwares_v1.0.tar.bz2 -C /lib/firmware/
If you cannot find the 6909 firmware:
wget http://www.tbsdtv.com/download/document/linux/dvb-fe-mxl5xx.fw
sudo cp dvb-fe-mxl5xx.fw /lib/firmware/
Now load the drivers: either reboot, or try loading the proper module for your card, e.g., tbsecp3 for many cards:
sudo modprobe tbsecp3
Check /var/log/debug for messages. If there are i2c_xfer error messages, try editing the file tbsecp3-cards.c. In that file lcate the entry for your card and change i2c_speed to 9.
If you have this problem then report it. Also report if the solution works,
These drivers were designed for use with neumoDVB to support advanced features provided by some cards:
- Spectrum acquisition.
- Constellation plots.
- Blind scanning.
- Supporting cards with RF mixes, which allow multiple demods to connect to the same tuner
- Stable identification of cards even when they are inserted in different orders (USB device) or placed in different slots.
- Providing advanced information for the stid135 based cards through sysfs and allowing certain parameters to be set through sysfs for those cards.
To make use or optimal use of these features, application programs should adhere to a new extended ``neumo-DVB'' interface, but the drivers were designed to be also backward compatable
neumoDVB detects the presence of these drivers and then will exploit the advanced features; if the drivers are not loaded if falls back to the DVB-apiV5 interface
In principle no changes are needed, and even without changes for stid135 based cards, through the sysfs interface it is possible to obtain more information about the cards and what they are doing. Also it is possible to slightly enhance using existing programs, such as tvheadend.
-
Through /sys/module/stid135/... it is possible to figure out which adapter belongs to which card.
-
Each card has one temperature property per stid135 chip, which contains the current temperature in Celcius.
-
Each card has a blindscan_always property. By setting '/sys/module/stid135/card0/blindscan_always' to 1, the stid135 driver will blindscan muxes on that card (card0). For instance if TvHeadend thinks that a mux is QPSK and has a symbolrate of 20kS/s, but in reality it has PSK8 modulation and a symbolrate of 30kS/s, tuning will fail without this setting, but will succeed with it. The downside is that the web interface of TvHeadend will still show the erroneous parameters. The upside is that scanning becomes easier.
Note that the proper way to set a sysfs parameter is (as an example)
echo 1 | sudo tee /sys/module/stid135/card0/blindscan_always -
Each adapter (or rather: demodulator) has a default_rf_in property. The value of this is a number indicating the physical input to which the adapter will be connected by default, if applications do not use the neumo-DVB api. For example, on tbs6909X, the default value for /sys/module/stid135/card0/chip0/demodX/default_rf_in will be X modulo 8, which means that two demodulators are connected to each of the four RF inputs.
In case you only have one cable connected to RF input 0, you can set all of the default_rf_in values to 0 and then configure TvHeadend to treat adapters 1...7 as slave adapters connected to master adapter 0. This then will allow simulatenous viewing or recording of channels spread over 8 different muxes in the same satellite band (e.g., horizontal Ku-low).
Note that TvHeadend will probably have difficulties coping with that much data, so it is best to stick with a smaller number of slave tuners.
This API has been kept mostly compatible with the existing DVB-V5 api, both internally in the kernel and externally towards user applications. However, the kernel-side API is not binary compatile (yet) with DVB-apiV5 and requires recompilation of all DVB modules that the user wants to use, even those not supporting neumoDVB.
User space applications should proceed as follows
-
First check for the presence of /sys/module/dvb_core/info/version. If this entry exists, it means that the neumoDVB drivers have been loaded, otherwise the application should fall back to DVB-apiV5. The version number in that sysfs file can also be used to distinghuish between different versions of the drivers. Note that the neumoDVB api is not yet frozen.
-
Using the FE_GET_EXTENDED_INFO ioctl, get information about the installed cards and adapters, specificaly their names (for use in GUI and in log files) and their MAC address. The latter is a unique id, which can be used to associate configuration information. For instance, the adapter number of a specific adapter may differ from one boot to the next when a card has been removed, or a new one has been inserted. However, the MAC address will always remain the same.
-
When tuning to a specific mux, first call the FE_SET_RF_INPUT ioctl. This is used to connect a demodulator to a specific RF_INPUT, but also to synchronize secondary device (LNBs and switches) configuration when multiple demodulators connect to the same tuner and thus to the same LNB and switches.
Being able to select a specific RF_INPUTs means that card operation becomes much more flexible. For instance, it is possible to connect more than 2 demodulators to the same input cable temporarily and as needed. In case each input is connected to a different LNB for a different satellite, it is possible to receive up to 8 different muxes on TBS6909V2 or up to 16 muxes on TBS6916 on the same satellite. With the standard DVB-v5 api drivers only 2 would be possible, because of the choice to pair 2 tuners to each RF_INPUT in a fixed manner.
Another problem not handled by the standard drivers is that a slave adapter should wait with tuning until it is certain that secondary equipment has been configured. For instance many programs are multi threaded. If the thread for the master tuner is delayed for some reason, it may happen that the master tuner has not yet finished sending DiSeqC commands when the slave tuner starts tuning and then slave tuning will fail. Of course it is possible to prevent this at the application level, but neumoDVB handles it in the drivers. This allows multiple applications to synchronize such access.
Concretely, when calling FE_SET_RF_INPUT, the application can specificy whether the demodulator will become master or slave. Typically an application will specify 'master' for the first tune, and 'slave' for subsequent tune's using the same RF_INPUT. An application can also specify 'master or slave'. In this case the drivers will make the adapter that makes the first ioctl the master and the other ones slaves. In all cases, when the drivers receive the ioctl, they will enforce proper execution of master requests before related slave requests can start.
The ioctl FE_SET_RF_INPUT caller should specifify
** rf_input: the desired tuner and cable to connect to
** mode: whether the tuner wants to become master (and agrees to configure LNB and switches), slave (agrees to not configure LNB and switches), or both.
** owner: a unique identifier for the calling application. Applications can only use resources (tuners, demodulators) if they are not in use by another application. Typically this should be the process id.
** config_id: a number which is incremented each time the application will reconfigure an RF_INPUT, which means: select a different LNB, or a different satellite band.
Whenever the driver notices an update in config_id, it will wait for all demodulators to release resources reserved with an older config_id value before allowing FE_SET_RF_INPUT ioctl's (including the one using the new config_id for the first time) to succeed. This loosens the synchronisation requirements on the application. For instance the application can call FE_SET_RF_INPUT for a master and slave demodulator in parallel on two threads. If for some reason the master ioctl call is delayed until after the slave ioctl call, the driver will do the right thing: fail one or both of the calls and inform the calling threads (through the ioctl return value) that this failure is only temporary and that they should retry the call after waiting for a brief period.
The ioctl's return value indicates
** a result: master or slave. If the result is 'master', the adapter should proceed with setting voltages, tones, sending diseqc commands, and then finally perform a tune. If the result is 'slave', then the caller can be certain that secondary equipment is now ready and the caller can start tuning its adapter.
** or permanent failure (e.g., requesting a non-existing RF_INPUT)
** or temporary failure: it is not yet possible to select the RF_INPUT, either because a master demodulator has not yet finished configuring secondary equipment (which the drivers can tell, see below), or because some other demodulators still need to release the tuner but have not done so. The calling thread can simply retry after sleeping e.g., 10 milliseconds, or the application can provide a locking mechanism to prevent this from happening (warning: this tends to be slower)
If the calling thread receives a 'slave' result, it should proceed directly with tuning. If it receives a 'master result', it should make FE_SET_VOLTAGE, FE_SET_TONE and FE_DISEQC_SEND_MASTER_CMD commands as needed, and also respect any delays needed by the secondary equipment to correctly power up. At this stage the calling thread should tune the adapter, using FE_SET_PROPERTY, and include a DTV_SET_SEC_CONFIGURED property. This informs the drivers that the secondary equipment is ready for use. From this stage on FE_SET_RF_INPUT ioctls for the same RF_INPUT will succeed, provided they use the current config_id value.
-
Ther remainder of the tuning process is similar as with the standard DVB-v5 api, except that additional tuning properties have been added to indicate blind scanning and that additional properties are returned to indicate discovered modulation parameters.
- Added sysfs entries in /sys/modules/stid135/
- Allow setting the default rf input for each demod, for use with tvheadend. This allows more than one slave tuner to use the same rf input connector on the card.
- Incorporated changes from the official tbs drivers up to July 11 2024.
- Improved determination of card mac addresses and generating fake mac addresses should the card not have one set.
- Support for the tbs6916 card.
- Bug: stid135 based cards sends out 21kHz tone and diseqc base frequency instead of 22kHz and this causes some diseqc switcches to sometimes ignore commands.
- Provide additional ioctls to support "syncrhonized" calls, where one adapter can wait on another adapter to finish setting voltages, tones and sending diseqc commands
- Protection against drivers which blindly assume name to be of size 128.
- Bug: fe_read_status should not return -1 on timeout.
- stv091x: fix isi scan.
- Bug: tuning loop runs to early when diseqc is sent but no tuning info is present yet.
- Update for linux 6.2 - 6.6 kernels
- compiles also on ubuntu 23.0
- Integrated latest changes from tbs linux_media
- Avoid out of bounds array indexing
- Improved voltage setting and related internal state management
- si2157 double free bug
- si2158 integrates some tns code
##Kernel support
- Update for linux 6 kernel
- compiles 6.1
- Improved logging.
- Avoid null pointer dereference when short_name not sent for 2nd frontend
- tbsecp3: set default mode to 1
- Do not send diseqc in mode=0; remove dead code
- Experimental fix for cards without short name; short name for tbs6908
- Bug: incorrect tone and voltage returned when tone and voltage are set via ioctl
- Bug: bbframe mode not reset in some cases
- Set rf_in=0 for non neumodvb cards
- Different way to initialize rf_inputs.
- rename tuner_active to rf_in_selected.
- Improved debug logging: add demod number; use numbering starting at 0
- Enable bbframes for GSE
- ts_nosync (code not yet active
- wideband support (untested)
- matype not set in some cases.
- select_min_isi sometimes fails, resulting in no tune
- Bug: after pls_seacrch fails, restore default pls
- Redefine FE_HAS_TIMING_LOCK to be different from FE_OUT_OF_RESOURCES, which confuses dvblast
- cx231xx correct MAC extraction after power cycle
- BUG: incorrect reporting of FE_OUT_OF_RESOURCES when lock fails
- Temporary fix to avoid crash on module unload
- Bug: when auto-selecting a stream_id, ensure that selected stream_id is returned to driver, rather than -1
- Introduce state_sleep; release mutex during sleep, to avoid delays in parallel operation of multiple demods
- Introduce base_lock, base_unlock, base_trylock
- Increase number of events in event queue
- Bug: slow closing of frontend because of needless locking
- Disallow turning off voltage when tuner is still in use
- Defaults for rf_inputs property; More stable faking of missing mac_address
- Possible module unload bug for tbs6590
- Incorrect processing of DVB_STOP ioctl. Fix includes workaround for bad user space code containing the same bug
- Bug: interrupting fft spectrum sometimes causes crash
- Bug: need to lock mutex during spectrum scan sweep.
- Adapter name retrieval; add short names for adapters.
- Add FE_SET_RF_INPUT ioctl; add rf_inputs fields to extended frontend info;
- Add card_short_name
- Bug: memory access beyond end of array causing kernel crash
- Do not apply center frequency shift for low symbol rates. Improves locking of low symbol rate muxes?
- Bug: voltage remains on after frontend is released
- Bug: crash on module onload (chip_proc_close)
- Always use "local" value for faked mac addresses.
- distinghuish between mac address of card and adapter
- Suppress some compiler warnings
- Expose default rf_in for each dvb adapter
- Fixes for tbs6983 (UNTESTED; may break other stv091x cards)
- Bug: tone not set on high band with stv091x
- Bug: stv091x needs mutex protection when called from dvb_frontend;
- tbs5927 - set correct frequency limits
- tbs5927: add card_address
- tbs5927 add "usb" to bus address
- set_voltage call accidentally removed from tbs5927
- Proper mac address and card name for tbs5927
- tbs6903x: Reduce overclocking to avoid i2c nack errors at startup
- tbs6903x_V2 has only 2 rf inputs.
- tbs6903x: allow both tuners to connect to both rf inputs
- Allow exposing registers of multiple stid135 cards in /proc
- Updated spectral scan algorithm (algo 5)
- debug logging
- Bug: force frame and continous mode not reset
- Add more error detection
- Add dummy plf detection
- simplify fe_stid135_get_signal_info
- stid135 Bug: Add code which ran in get_frontend into read_status because get_frontend is no longer called
- Remove stid135-fe.h; make some functions static
- Improved debug logging: add demod number; use numbering starting at 0
- stid135: improved lock status reporting
- stid135: deadlock in spectrum_scan
- In stid135_fft, assume all functions are called with base_lock held.
- stid135: correctly handle low rolloff factors indicated by alternating matype
- stid135: disable get_frontend
- Handle out of llr condition
- stid135: allow writing registers
- Overclock i2c bus on stid135 based cards.
- Rename spectrum scan related enum; allow rf_input selection on stid135;
- stid135: report that only 4 out of 8 tuners support fft scan.
- Bug: stid135 22kHz still on when device not in use
- Bug: incorrect docs for stid135-fe module parameter
- Bug: accidentally disabled fe_stid135_init_fft
- Re-add tbs6916 (16 tuner optical card)
- em28xx crash on usb disconnect.
- em28xx crash on module unload
- m88rs6060: remove uneeeded reads
- tbs6904se: increase i2c speed (experimental)
- m88rs6060: faster spectrum scan (psyborg55)
- shortname for tbs6522
- tas2101: pause after activating demod, to return correct SNR
- tas2101: set proper lock flags
- tas2101: set timing lock status
- tas2101: increase constellation size
- tbs5990: set proper card_mac_address and rf_input.
- tbs5990: add bus address
- tbs5990: incorrect mac address read.
- si2183 patch
- si2183: report timing lock to avoid problems in user apps.
- Bug: si2183 sets incorrect frequency limits
- Bug: si2183 sets incorrect frequency limits
- tbs6504: ensure all frontends on the same adapter have same faked macaddress
- Workaround for tbs6504 not detecting stream_type correctly
- Blindscan and spectrum upport for montage m88rs60606 based cards: tbs6902SE and tbs2904SE.
- Support m883s6060 module unloading
- stid135: BER is now reported properly othrough the PRE instead of POST error counters
- Improved correction of discontinuities in spectrum due to small errors in RF level
- stid135: detected multi-stream IDs are now accumalated internally
- Added DTV_BIT_RATE readout via dvbapi
- stid135: improper estimation of required llr rate, causing rai multistream on 5.0W to not tune sometimes (green blocks in picture)
- stid135: changed default spectral resolution: slightly slower scan, but more narrow-band muxes found
- Add support for timing lock flag
- stv091x: return more correct data about currently tuned mux (instead of returning what user requested)
- si2183 based cards: blindscan cannot discover stream_ids in multistreams, unless it is given one of them when starting the blindscan. In that case, it will find the other ones
User space tools for using blindscan can be found at https://github.com/deeptho/blindscan
First install the required compilers, git ... You may also need libproc-processtable-perl (e.g., on ubuntu)
mkdir ~/blindscan_kernel
cd ~/blindscan_kernel
Check out the actual drivers. This uses the default branch which is called deepthought
git clone --depth=1 https://github.com/deeptho/linux_media.git ./media
Then check out a copy of DeepThought's media_build (try tbs media_build if it does not work)
git clone https://github.com/deeptho/media_build
Make sure software for kernel compilation is installed. For instance on fedora, with MYKERNEL the exact kernel version you are running:
sudo dnf install -y patchutils
sudo dnf install -y ccache
sudo dnf install -y kernel-devel-MYKERNEL
sudo dnf install -y perl-File-Copy #not needed?
sudo dnf install -y perl
sudo dnf install -y perl-Proc-ProcessTable
cd media_build
git checkout deepthought
git reset --hard
make dir DIR=../media
make distclean
./install.sh
Last but not least, install rsyslog so that kernel debug messages are stored in the file system in /var/log/debug:
sudo dnf install -y rsyslog
sudo vi /etc/rsyslog.conf # add "kern.debug /var/log/debug" line
sudo systemctl enable rsyslog
sudo systemctl start rsyslog #to have log messages in /var/log/debug
Now install the firmware (if needed):
wget http://www.tbsdtv.com/download/document/linux/tbs-tuner-firmwares_v1.0.tar.bz2
sudo tar jxvf tbs-tuner-firmwares_v1.0.tar.bz2 -C /lib/firmware/
If you cannot find the 6909 firmware:
wget http://www.tbsdtv.com/download/document/linux/dvb-fe-mxl5xx.fw
sudo cp dvb-fe-mxl5xx.fw /lib/firmware/
Now load the drivers: either reboot, or try loading the proper module for your card, e.g., tbsecp3 for many cards:
sudo modprobe tbsecp3
Check /var/log/debug for messages. If there are i2c_xfer error messages, try editing the file tbsecp3-cards.c. In that file lcate the entry for your card and change i2c_speed to 9.
If you have this problem then report it. Also report if the solution works,