Skip to content

Interfaces

Hemerson Farias edited this page Aug 18, 2018 · 15 revisions

The EPS module is connected to the other modules using the PC104 connector. The solar panels, the kill-switches, the remove before flight, the RTDs, the heater, the batteries charger connector and the JTAG pins are connected using Molex Picoblade connectors. The EPS module also has a jumper that connects the MCU VCC to the JTAG VCC and a header to debug the board via UART protocol. In the following sections each connector is detailed, with a picture showing the location on the EPS PCB and a table explaining each pin function.

Solar Panels Connectors

Number Name Description
1 PGND Power Ground
2 PGND Power Ground
3 Panel+ Solar panel positive terminal
4 Panel+ Solar panel positive terminal

Kill-Switches Connectors

Number Name Description
1 Common Kill-Switch Mosfet Gate Connection
2 Common Kill-Switch Mosfet Gate Connection
3 NO Kill-Switch +Vbat connection
4 NO Kill-Switch +Vbat connection
5 NC Kill-Switch PGND pull-down connection
6 NC Kill-Switch PGND pull-down connection

External Batteries Charger Connector

Number Name Description
1 Vcharging_batteries Batteries positive charging pin
2 Vcharging_batteries Batteries positive charging pin
3 PGND Power Ground
4 PGND Power Ground

Remove Before Flight Connector

Number Name Description
1 +RBF Connected to +Vbat
2 +RBF Connected to +Vbat
3 -RBF Connected to mosfet gate
4 -RBF Connected to mosfet gate

RTD1 Connector

Number Name Description
1 RTD6 RTD6 positive
connection
2 RTD common RTD negative
connection
3 RTD2 RTD2 positive
connection
4 RTD common RTD negative
connection
5 RTD3 RTD3 positive
connection
6 RTD common RTD negative
connection
7 NTC Batteries charger
NTC connection
8 RTD common RTD negative
connection

RTD2 Connector

Number Name Description
1 RTD0 RTD0 positive
connection
2 RTD common RTD negative
connection
3 RTD1 RTD1 positive
connection
4 RTD common RTD negative
connection
5 RTD4 RTD4 positive
connection
6 RTD common RTD negative
connection
7 RTD5 RTD5 positive
connection
8 RTD common RTD negative
connection

External Batteries PCB Connector

Number Name Description
1 +Vbat Batteries positive pin
2 +Vbat Batteries positive pin
3 +Vbat Batteries positive pin
4 +Vbat Batteries positive pin
5 -Vbat Batteries negative pin
6 -Vbat Batteries negative pin
7 -Vbat Batteries negative pin
8 -Vbat Batteries negative pin
9 Vbat_common Batteries middle connection
10 Vbat_common Batteries middle connection

Batteries Heaters Connector

Number Name Description
1 Vmain_power Heater 1 positive connection
2 Vmain_power Heater 1 positive connection
3 -Heater1 Heater 1 negative connection
4 -Heater1 Heater 1 negative connection
5 Vmain_power Heater 2 positive connection
6 Vmain_power Heater 2 positive connection
7 -Heater2 Heater 2 negative connection
8 -Heater2 Heater 2 negative connection

PC104

H1 (internal) H2 (external)
Pin Nº Pin Name Pin Nº Pin Name Pin Nº Pin Name Pin Nº Pin Name
1 GND 2 GND 1 GND 2 GND
3 GND 4 GND 3 GND 4 GND
5 6 5 BUS6 6
7 8 7 8
9 10 Beacon PA regulator enable 9 10
11 12 Main Radio PA regulator enable 11 12
13 14 13 14
15 16 15 16
17 18 17 18
19 20 19 20
21 22 21 22
23 24 23 24
25 26 25 Payload regulator output 26 Payload regulator output
27 28 27 EPS-Beacon regulator output 28 EPS-Beacon regulator output
29 GND 30 GND 29 GND 30 GND
31 GND 32 GND 31 GND 32 GND
33 34 33 34
35 36 35 Antenna regulator output 36 Antenna regulator output
37 38 37 38
39 40 39 40
41 BUS0 SDA 42 41 42
43 BUS0 SCL 44 43 44
45 OBDH regulator output 46 OBDH regulator output 45 Main power bus 46 Main power bus
47 Payload regulator output 48 Payload regulator output 47 48
49 Main radio PA regulator output 50 Main radio PA regulator output 49 50
51 Beacon PA regulator output 52 Beacon PA regulator output 51 52