Skip to content

Sample Bootlogs

Jump to bottom
gtxaspec edited this page Jan 31, 2024 · 4 revisions

ETH PHY

OpenIPC U-Boot SPL 2013.07-g218031e-dirty (Jan 22 2024 - 06:42:04)
Timer init
CLK stop
PLL init
pll_init:366
pll_cfg.pdiv = 10, pll_cfg.h2div = 5, pll_cfg.h0div = 5, pll_cfg.cdiv = 1, pll_cfg.l2div = 2
nf=118 nr = 1 od0 = 1 od1 = 2
cppcr is 07605100
CPM_CPAPCR 0750510d
nf=84 nr = 1 od0 = 1 od1 = 2
cppcr is 05405100
CPM_CPMPCR 07d0590d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPVPCR 0640510d
cppcr 0x9a773310
apll_freq 1404000000 
mpll_freq 1000000000 
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 500000000
cclk  1404000000
l2clk 702000000
h0clk 200000000
h2clk 200000000
pclk  100000000
CLK init
SDRAM init
sdram init start
DDR clk rate 500000000
SDRAM init ok
board_init_r
image entry point: 0x80100000


OpenIPC U-Boot 2013.07-g218031e-dirty (Jan 22 2024 - 06:42:04)

Platform: ISVP (Ingenic XBurst)
Built profile: T31N
SOC Name: T31N
DRAM:  64 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 686k for U-Boot at: 83f54000
Reserving 32832k for malloc() at: 81f44000
Reserving 32 Bytes for Board Info at: 81f43fe0
Reserving 124 Bytes for Global Data at: 81f43f64
Reserving 256k for boot params() at: 81f03f64
Stack Pointer at: 81f03f48
Now running in RAM - U-Boot at: 83f54000
MMC:   msc: 0
SF:    Vendor: 20
SF:    Detected XM25QH64C
Net:   HW Ethernet address exists
In:    serial
Out:   serial
Err:   serial
GPIO:  Setting gpio_default
GPIO:  62 set to output high
GPIO:  Setting gpio_default_ircut
GPIO:  25 set to input
GPIO:  26 set to input
GPIO:  52 set to input
GPIO:  53 set to input
GPIO:  49 set to input
GPIO:  50 set to input
ETH:   Searching for valid PHY
ETH:   Found PHY 0:0x0-0x128
ETH:   SPEED:2, DUPLEX:2
GPIO:  gpio_user: No GPIO env settings provided
GPIO:  gpio_motor_v: No GPIO env settings provided
GPIO:  gpio_motor_h: No GPIO env settings provided
MMC:   SD card disabled
KEY:   ###### Press Ctrl-C now to interrupt boot... loading in 1s ######
SF:    Vendor: 20
SF:    Detected XM25QH64C
SF:    probe command completed in 4 ms
SQ:    SquashFS found at 0x220000
SF:    1900544 bytes @ 0x50000 Read: OK
SF:    read command completed in 612 ms
###### Booting kernel from Legacy Image at 0x80600000 ######

WiFi + MMC

OpenIPC U-Boot SPL 2013.07-g218031e-dirty (Jan 22 2024 - 06:38:48)
Timer init
CLK stop
PLL init
pll_init:366
pll_cfg.pdiv = 10, pll_cfg.h2div = 5, pll_cfg.h0div = 5, pll_cfg.cdiv = 1, pll_cfg.l2div = 2
nf=116 nr = 1 od0 = 1 od1 = 2
cppcr is 07405100
CPM_CPAPCR 0740510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPMPCR 0640510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPVPCR 0640510d
cppcr 0x9a7b5510
apll_freq 1392000000 
mpll_freq 1200000000 
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 600000000
cclk  1392000000
l2clk 696000000
h0clk 240000000
h2clk 240000000
pclk  120000000
CLK init
SDRAM init
sdram init start
DDR clk rate 600000000
SDRAM init ok
board_init_r
image entry point: 0x80100000


OpenIPC U-Boot 2013.07-g218031e-dirty (Jan 22 2024 - 06:38:48)

Platform: ISVP (Ingenic XBurst)
Built profile: T31X
SOC Name: T31X
DRAM:  128 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 686k for U-Boot at: 83f54000
Reserving 32832k for malloc() at: 81f44000
Reserving 32 Bytes for Board Info at: 81f43fe0
Reserving 124 Bytes for Global Data at: 81f43f64
Reserving 256k for boot params() at: 81f03f64
Stack Pointer at: 81f03f48
Now running in RAM - U-Boot at: 83f54000
MMC:   msc: 0
SF:    Vendor: 1c
SF:    Detected EN25QH128A
Net:   HW Ethernet address exists
In:    serial
Out:   serial
Err:   serial
GPIO:  Setting gpio_default
GPIO:  62 set to output high
GPIO:  Setting gpio_default_ircut
GPIO:  25 set to input
GPIO:  26 set to input
GPIO:  52 set to input
GPIO:  53 set to input
GPIO:  49 set to input
GPIO:  50 set to input
Net:   Network disabled
GPIO:  Setting gpio_default_net
GPIO:  61 set to output low
GPIO:  48 set to output low
GPIO:  gpio_user: No GPIO env settings provided
GPIO:  Setting gpio_motor_v
GPIO:  59 set to input
GPIO:  61 set to input
GPIO:  62 set to input
GPIO:  63 set to input
GPIO:  Setting gpio_motor_h
GPIO:  52 set to input
GPIO:  53 set to input
GPIO:  57 set to input
GPIO:  51 set to input
MMC:   SD card disabled
KEY:   ###### Press Ctrl-C now to interrupt boot... loading in 1s ######
SF:    Vendor: 1c
SF:    Detected EN25QH128A
SF:    probe command completed in 4 ms
SQ:    SquashFS found at 0x220000
SF:    1900544 bytes @ 0x50000 Read: OK
SF:    read command completed in 612 ms
###### Booting kernel from Legacy Image at 0x80600000 ######
Clone this wiki locally