octeon: n821: sysupgrade for Cisco vEdge 1000

This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.

The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.

In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.

Tested on a Cisco vEdge 1000.

Signed-off-by: Christian Svensson <[email protected]>
Link: openwrt/openwrt#16140
Signed-off-by: Robert Marko <[email protected]>

target/linux/octeon/base-files/lib/preinit/79_move_config

@@ -4,29 +4,46 @@ move_config() {
 	. /lib/upgrade/common.sh
 
 	local device="$1"
+	local fstype="$2"
 	[ -n "$device" ] && [ -b "$device" ] && {
-		mount -t vfat "$device" /mnt
+		mount -t "${fstype}" "$device" /mnt
 		[ -f "/mnt/$BACKUP_FILE" ] && mv -f "/mnt/$BACKUP_FILE" /
 		umount /mnt
 	}
 }
 
+octeon_get_n821_disk() {
+	local partnum=$1
+	local MAJOR MINOR DEVNAME DEVTYPE
+	while read line; do
+		export -n "${line}"
+	done < $(find /sys/bus/platform/devices/16f0000000000.ehci/ -path \*block/sd[a-z]/uevent)
+	echo "/dev/${DEVNAME}${partnum}"
+}
+
 octeon_move_config() {
 	. /lib/functions.sh
 
 	case "$(board_name)" in
 		erlite|\
 		ubnt,usg)
-			move_config "/dev/sda1"
+			move_config "/dev/sda1" "vfat"
 			;;
 		itus,shield-router)
-			move_config "/dev/mmcblk1p1"
+			move_config "/dev/mmcblk1p1" "vfat"
 			;;
 		er|\
 		ubnt,edgerouter-4|\
 		ubnt,edgerouter-6p)
-			move_config "/dev/mmcblk0p1"
+			move_config "/dev/mmcblk0p1" "vfat"
 			;;
+		cisco,vedge1000)
+			# Copy from the internal USB disk's first partition.
+			# It is resolved from the device path to not be dependent on which
+			# /dev/sd? path it is at, nor which UUID it happens to have.
+			move_config "$(octeon_get_n821_disk 1)" "ext2"
+			;;
+
 	esac
 }
 

target/linux/octeon/base-files/lib/upgrade/platform.sh

@@ -2,11 +2,21 @@
 # Copyright (C) 2021 OpenWrt.org
 #
 
+if [ -x /usr/sbin/blkid ]; then
+  RAMFS_COPY_BIN="/usr/sbin/blkid"
+fi
+
 platform_get_rootfs() {
 	local rootfsdev
+	local rootpartuuid
 
 	if read cmdline < /proc/cmdline; then
 		case "$cmdline" in
+			*root=PARTUUID=*)
+				rootpartuuid="${cmdline##*root=PARTUUID=}"
+				rootpartuuid="${rootpartuuid%% *}"
+				rootfsdev="$(blkid -o device -t PARTUUID="${rootpartuuid}")"
+			;;
 			*root=*)
 				rootfsdev="${cmdline##*root=}"
 				rootfsdev="${rootfsdev%% *}"
@@ -17,10 +27,20 @@ platform_get_rootfs() {
 	fi
 }
 
+platform_get_n821_disk() {
+	local partnum=$1
+	local DEVNAME
+	while read line; do
+		export -n "${line}"
+	done < $(find /sys/bus/platform/devices/16f0000000000.ehci/ -path \*block/sd[a-z]/uevent)
+	echo "/dev/${DEVNAME}${partnum}"
+}
+
 platform_copy_config_helper() {
 	local device=$1
+	local fstype=$2
 
-	mount -t vfat "$device" /mnt
+	mount -t "${fstype}" "$device" /mnt
 	cp -af "$UPGRADE_BACKUP" "/mnt/$BACKUP_FILE"
 	umount /mnt
 }
@@ -29,15 +49,18 @@ platform_copy_config() {
 	case "$(board_name)" in
 	erlite|\
 	ubnt,usg)
-		platform_copy_config_helper /dev/sda1
+		platform_copy_config_helper /dev/sda1 vfat
 		;;
 	itus,shield-router)
-		platform_copy_config_helper /dev/mmcblk1p1
+		platform_copy_config_helper /dev/mmcblk1p1 vfat
 		;;
 	er|\
 	ubnt,edgerouter-4|\
 	ubnt,edgerouter-6p)
-		platform_copy_config_helper /dev/mmcblk0p1
+		platform_copy_config_helper /dev/mmcblk0p1 vfat
+		;;
+	cisco,vedge1000)
+		platform_copy_config_helper "$(platform_get_n821_disk 1)" ext2
 		;;
 	esac
 }
@@ -61,14 +84,26 @@ platform_do_flash() {
 		echo "flashing Itus Kernel to /boot/$kernel (/dev/mmblk1p1)"
 		tar -Oxf $tar_file "$board_dir/kernel" > /boot/$kernel
 	else
-		mount -t vfat /dev/$kernel /boot
+		if [ "${board}" = "cisco,vedge1000" ]; then
+			local rootpartuuid
+			rootpartuuid="$(/usr/sbin/blkid -o value -s PARTUUID "${rootfs}")"
+			if [ -n "${rootpartuuid}" ]; then
+				echo "setting root partition to PARTUUID=${rootpartuuid}"
+				fw_setenv bootcmd 'usb start; ext2load usb 0:1 $loadaddr vmlinux.64; bootoctlinux $loadaddr coremask=f endbootargs rootfstype=squashfs rootwait root=PARTUUID='"${rootpartuuid}"
+			else
+				echo "WARNING: unable to figure out root partition UUID, leaving bootcmd unchanged"
+			fi
+			mount -t ext2 "${kernel}" /boot
+		else
+			mount -t vfat "${kernel}" /boot
+		fi
 
 		[ -f /boot/vmlinux.64 -a ! -L /boot/vmlinux.64 ] && {
 			mv /boot/vmlinux.64 /boot/vmlinux.64.previous
 			mv /boot/vmlinux.64.md5 /boot/vmlinux.64.md5.previous
 		}
 
-		echo "flashing kernel to /dev/$kernel"
+		echo "flashing kernel to $(awk '/\/boot/ {print $1}' /proc/mounts)"
 		tar xf $tar_file $board_dir/kernel -O > /boot/vmlinux.64
 		md5sum /boot/vmlinux.64 | cut -f1 -d " " > /boot/vmlinux.64.md5
 	fi
@@ -86,20 +121,27 @@ platform_do_upgrade() {
 	local rootfs="$(platform_get_rootfs)"
 	local kernel=
 
+	if [ ! -b "${rootfs}" ] && [ "${board}" = "cisco,vedge1000" ]; then
+		# Default to the built-in USB disk for N821
+		rootfs="$(platform_get_n821_disk 2)"
+	fi
 	[ -b "${rootfs}" ] || return 1
 	case "$board" in
 	er | \
 	ubnt,edgerouter-4 | \
 	ubnt,edgerouter-6p)
-		kernel=mmcblk0p1
+		kernel=/dev/mmcblk0p1
 		;;
 	erlite|\
 	ubnt,usg)
-		kernel=sda1
+		kernel=/dev/sda1
 		;;
 	itus,shield-router)
 		kernel=ItusrouterImage
 		;;
+	cisco,vedge1000)
+		kernel="$(platform_get_n821_disk 1)"
+		;;
 	*)
 		return 1
 	esac
@@ -123,7 +165,8 @@ platform_check_image() {
 	itus,shield-router | \
 	ubnt,edgerouter-4 | \
 	ubnt,edgerouter-6p | \
-	ubnt,usg)
+	ubnt,usg | \
+	cisco,vedge1000)
 		local kernel_length=$(tar xf $tar_file $board_dir/kernel -O | wc -c 2> /dev/null)
 		local rootfs_length=$(tar xf $tar_file $board_dir/root -O | wc -c 2> /dev/null)
 		[ "$kernel_length" = 0 -o "$rootfs_length" = 0 ] && {

target/linux/octeon/image/Makefile

@@ -100,13 +100,16 @@ define Device/cisco_vedge1000
   DEVICE_MODEL := vEdge 1000
   BOARD_NAME := cisco,vedge1000
   DEVICE_PACKAGES += \
+	blkid \
 	kmod-hwmon-jc42 \
 	kmod-hwmon-max6697 \
 	kmod-of-mdio \
 	kmod-rtc-ds1307 \
 	kmod-usb-dwc3 \
 	kmod-usb-storage-uas \
-	kmod-usb3
+	kmod-usb3 \
+	sfdisk \
+	uboot-envtools
   KERNEL := kernel-bin | append-dtb-elf
   KERNEL_DEPENDS := $$(wildcard $(DTS_DIR)/$(DEVICE_DTS).dts)
   DEVICE_DTS := cn6130_cisco_vedge1000