-
Notifications
You must be signed in to change notification settings - Fork 151
management_ha_test
Github Action edited this page May 1, 2024
·
2 revisions
- Test management HA
For each section of configuration below, prepare a gnmi.SetBatch with all the configuration items appended to one SetBatch. Then apply the configuration to the DUT in one gnmi.Set
using the replace option
- Connect DUT port-1, 2 and 3 to ATE port-1, 2 and 3
- Create VRF "mgmt" on DUT
- /network-instances/network-instance[name=mgmt]/config/name = mgmt
- /network-instances/network-instance[name=mgmt]/config/route-distinguisher = 64512:100
- Create an IPv6 networks
ateNetattached to ATE port-1, 2 and 3 - Create a loopback interface "lo1" on DUT and assign it an IPv6 address
- /interfaces/interface[name=lo1]/config/name = lo1
- /interfaces/interface[name=lo1]/config/type = softwareLoopback
- /interfaces/interface[name=lo1]/subinterfaces/subinterface[index=0]/ipv6/addresses/address/config/ip
- /interfaces/interface[name=lo1]/subinterfaces/subinterface[index=0]/ipv6/addresses/address/config/prefix-length
- Configure the loopback interface to participate in the VRF "mgmt"
- /network-instances/network-instance[name=mgmt]/interfaces/interface[name=lo1]/config/interface = lo1
- Configure IPv6 addresses on DUT and ATE ports 1 and 2. Configure them to participate in the VRF "mgmt"
- /interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/ip
- /interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/prefix-length
- /network-instances/network-instance[name=mgmt]/interfaces/interface/config/interface
- Configure IPv6 eBGP between DUT Port-1 <--> ATE Port-1 and DUT Port-2 <--> ATE Port-2 in VRF "mgmt"
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=BGP, name=BGP]/global/config/as = 64512
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=BGP, name=BGP]/global/config/router-id = <router_id>
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=BGP, name=BGP]/neighbor/config/peer-as = 64511
- Set default import and export policy to
ACCEPT_ROUTEfor the eBGP sessions- /network-instances/network-instance[name=mgmt]/protocols/protocol/bgp/neighbors/neighbor/afi-safis/afi-safi/apply-policy/config/default-import-policy
- /network-instances/network-instance[name=mgmt]/protocols/protocol/bgp/neighbors/neighbor/afi-safis/afi-safi/apply-policy/config/default-export-policy
- Advertise a default route from ATE to DUT throught both the BGP sessions
- Redistribute the loopback interface from DUT to ATE through both the BGP sessions
- Set address-family to
IPV6- /network-instances/network-instance/table-connections/table-connection/config/address-family
- Configure source protocol to
CONNECTED- /network-instances/network-instance/table-connections/table-connection/config/src-protocol
- Configure destination protocol to
BGP- /network-instances/network-instance/table-connections/table-connection/config/dst-protocol
- Configure default export policy to
ACCEPT_ROUTE- /network-instances/network-instance/table-connections/table-connection/config/default-export-policy
- Disable metric propogation by setting it to
true- /network-instances/network-instance/table-connections/table-connection/config/disable-metric-propagation
- Configure an IPv6 route-policy definition with the name
route-policy- /routing-policy/policy-definitions/policy-definition/config/name
- For routing-policy
route-policyconfigure a statement with the namestatement- /routing-policy/policy-definitions/policy-definition/statements/statement/config/name
- For routing-policy
route-policystatementstatementset policy-result asACCEPT_ROUTE- /routing-policy/policy-definitions/policy-definition/statements/statement/actions/config/policy-result
- Configure a prefix-set with the name
prefix-setand modeIPV6- /routing-policy/defined-sets/prefix-sets/prefix-set/config/name
- /routing-policy/defined-sets/prefix-sets/prefix-set/config/mode
- For prefix-set
prefix-setset the ip-prefix toloopback0 IPv6 address/maskand masklength toexact- /routing-policy/defined-sets/prefix-sets/prefix-set/prefixes/prefix/config/ip-prefix
- /routing-policy/defined-sets/prefix-sets/prefix-set/prefixes/prefix/config/masklength-range
- For routing-policy
route-policystatementstatementset match options toANY- /routing-policy/policy-definitions/policy-definition/statements/statement/conditions/match-prefix-set/config/match-set-options
- For routing-policy
route-policystatementstatementset prefix set toprefix-set- /routing-policy/policy-definitions/policy-definition/statements/statement/conditions/match-prefix-set/config/prefix-set
- Apply routing policy
route-policyfor redistribution to BGP- /network-instances/network-instance/table-connections/table-connection/config/export-policy
- Set address-family to
- Configure IPv6 addresses on DUT Port-3 and ATE Port-3
- /interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/ip
- /interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/prefix-length
- Configure DUT Port-3 to participate in the VRF "mgmt"
- /network-instances/network-instance[name=mgmt]/interfaces/interface/config/interface
- Configure a static route on ATE device of Port-3 destined to the DUT loopback with next-hop address of DUT Port-3 with administrative-distance or preference of 220
- Configure a IPv6 default static route on DUT in VRF "mgmt" pointing towards the IPv6 address of ATE Port-3 with Administrative Distance or Preference of 220
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=STATIC, name=static]/static-routes/static/config/prefix = ::/0
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=STATIC, name=static]/static-routes/static/next-hops/next-hop/index = 1
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=STATIC, name=static]/static-routes/static/next-hops/next-hop[index=1]/config/next-hop = ATE Port-3 IP
- /network-instances/network-instance[name=mgmt]/protocols/protocol[identifier=STATIC, name=static]/static-routes/static/next-hops/next-hop/config/preference = 220
- Generate ICMP echo (ping) sourced from the
ateNetnetwork destined towards the DUT loopback1 IPv6 address - Validate ICMP echo-reply is received by the ATE on Port-1 or Port-2
- Shutdown BGP session on Port-1
- Generate ICMP echo (ping) sourced from the
ateNetnetwork destined towards the DUT loopback1 IPv6 address - Validate ICMP echo-reply is received by the ATE on Port-2
- Bring up BGP session on Port-1 and shutdowm BGP on Port-2
- Generate ICMP echo (ping) sourced from the
ateNetnetwork destined towards the DUT loopback1 IPv6 address - Validate ICMP echo-reply is received by the ATE on Port-1
- Shutdown BGP session on Port-1 and Port-2
- Generate ICMP echo (ping) sourced from the
ateNetnetwork destined towards the DUT loopback1 IPv6 address - Validate ICMP echo-reply is received by the ATE on Port-3
- Bring up BGP session on Port-1 and Port-2
- Generate ICMP echo (ping) sourced from the
ateNetnetwork destined towards the DUT loopback1 IPv6 address - Validate ICMP echo-reply is received by the ATE on Port-1 or Port-2
The below yaml defines the OC paths intended to be covered by this test. OC paths used for test setup are not listed here.
paths:
## Config paths
/network-instances/network-instance/config/name:
/network-instances/network-instance/config/route-distinguisher:
/network-instances/network-instance/interfaces/interface/config/interface:
/interfaces/interface/config/name:
/interfaces/interface/config/type:
/interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/ip:
/interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/prefix-length:
/network-instances/network-instance/protocols/protocol/bgp/global/config/as:
/network-instances/network-instance/protocols/protocol/bgp/global/config/router-id:
/network-instances/network-instance/protocols/protocol/bgp/neighbors/neighbor/config/peer-as:
/network-instances/network-instance/protocols/protocol/bgp/neighbors/neighbor/afi-safis/afi-safi/apply-policy/config/default-import-policy:
/network-instances/network-instance/protocols/protocol/bgp/neighbors/neighbor/afi-safis/afi-safi/apply-policy/config/default-export-policy:
/network-instances/network-instance/table-connections/table-connection/config/address-family:
/network-instances/network-instance/table-connections/table-connection/config/src-protocol:
/network-instances/network-instance/table-connections/table-connection/config/dst-protocol:
/network-instances/network-instance/table-connections/table-connection/config/default-import-policy:
/network-instances/network-instance/table-connections/table-connection/config/disable-metric-propagation:
/routing-policy/policy-definitions/policy-definition/config/name:
/routing-policy/policy-definitions/policy-definition/statements/statement/config/name:
/routing-policy/policy-definitions/policy-definition/statements/statement/actions/config/policy-result:
/routing-policy/defined-sets/prefix-sets/prefix-set/config/name:
/routing-policy/defined-sets/prefix-sets/prefix-set/config/mode:
/routing-policy/defined-sets/prefix-sets/prefix-set/prefixes/prefix/config/ip-prefix:
/routing-policy/defined-sets/prefix-sets/prefix-set/prefixes/prefix/config/masklength-range:
/routing-policy/policy-definitions/policy-definition/statements/statement/conditions/match-prefix-set/config/match-set-options:
/routing-policy/policy-definitions/policy-definition/statements/statement/conditions/match-prefix-set/config/prefix-set:
/network-instances/network-instance/protocols/protocol/static-routes/static/config/prefix:
/network-instances/network-instance/protocols/protocol/static-routes/static/next-hops/next-hop/index:
/network-instances/network-instance/protocols/protocol/static-routes/static/next-hops/next-hop/config/next-hop:
/network-instances/network-instance/protocols/protocol/static-routes/static/next-hops/next-hop/config/preference:
## State paths: N/A
rpcs:
gnmi:
gNMI.Set:
Replace:- FFF
-
Home
- Test Plans
- ACCTZ-1.1: Record Subscribe Full
- ACCTZ-2.1: Record Subscribe Partial
- ACCTZ-3.1: Record Subscribe Non-gRPC
- ACCTZ-4.1: Record History Truncation
- ACCTZ-4.2: Record Payload Truncation
- Authz: General Authz (1-4) tests
- CNTR-1: Basic container lifecycle via
gnoi.Containerz. - CNTR-2: Container network connectivity tests
- Credentialz-1: Password console login
- Credentialz-2: SSH Password Login Disallowed
- Credentialz-3: Host Certificates
- Credentialz-4: SSH Public Key Authentication
- Credentialz-5: Hiba Authentication
- DP-1.2: QoS policy feature config
- DP-1.3: QoS ECN feature config
- DP-1.4: QoS Interface Output Queue Counters
- DP-1.7: One strict priority queue traffic test
- DP-1.8: Two strict priority queue traffic test
- DP-1.9: WRR traffic test
- DP-1.10: Mixed strict priority and WRR traffic test
- DP-1.11: Bursty traffic test
- DP-1.14: QoS basic test
- example-0.1: Topology Test
- FP-1.1: Power admin DOWN/UP Test
- gNMI-1.1: cli Origin
- gNMI-1.2: Benchmarking: Full Configuration Replace
- gNMI-1.3: Benchmarking: Drained Configuration Convergence Time
- gNMI-1.4: Telemetry: Inventory
- gNMI-1.5: Telemetry: Port Speed Test
- gNMI-1.8: Configuration Metadata-only Retrieve and Replace
- gNMI-1.9: Get requests
- gNMI-1.10: Telemetry: Basic Check
- gNMI-1.11: Telemetry: Interface Packet Counters
- gNMI-1.12: Mixed OpenConfig/CLI Origin
- gNMI-1.13: Optics Telemetry, Instant, threshold, and miscellaneous static info
- gNMI-1.14: OpenConfig metadata consistency during large config push
- gNMI-1.15: Set Requests
- gNMI-1.16: fabric redundancy test
- gNMI-1.17: Controller Card redundancy test
- gNMI-1.18: gNMI subscribe with sample mode for backplane capacity counters
- gNMI-1.19: ConfigPush after Control Card switchover
- gNMI-1.20: Telemetry: Optics Thresholds
- gNMI-1.21: Integrated Circuit Hardware Resource Utilization Test
- gNMI-1.22: Controller card port attributes
- gNMI-1.27: gNMI Sample Mode Test
- GNMI-2: gnmi_subscriptionlist_test
- gNOI-2.1: Packet-based Link Qualification
- gNOI-3.1: Complete Chassis Reboot
- gNOI-3.2: Per-Component Reboot
- gNOI-3.3: Supervisor Switchover
- gNOI-3.4: Chassis Reboot Status and Reboot Cancellation
- gNOI-4.1: Software Upgrade
- gNOI-5.1: Ping Test
- gNOI-5.2: Traceroute Test
- gNOI-5.3: Copying Debug Files
- gNOI-6.1: Factory Reset
- Health-1.1: Generic Health Check
- Health-1.2: Healthz component status paths
- MGT-1: Management HA solution test
- MTU-1.3: Large IP Packet Transmission
- OC-1.2: Default Address Families
- OC-26.1: Network Time Protocol (NTP)
- P4RT-1.1: Base P4RT Functionality
- P4RT-1.2: P4RT Daemon Failure
- P4RT-2.1: P4RT Election
- P4RT-2.2: P4RT Metadata Validation
- P4RT-3.1: Google Discovery Protocol: PacketIn
- P4RT-3.2: Google Discovery Protocol: PacketOut
- P4RT-3.21: Google Discovery Protocol: PacketOut with LAG
- P4RT-5.1: Traceroute: PacketIn
- P4RT-5.2: Traceroute Packetout
- P4RT-5.3: Traceroute: PacketIn With VRF Selection
- P4RT-6.1: Required Packet I/O rate: Performance
- P4RT-7.1: LLDP: PacketIn
- P4RT-7.2: LLDP: PacketOut
- Replay-1.0: Record/replay presession test
- Replay-1.1: Record/replay diff command trees test
- Replay-1.2: P4RT Replay Test
- RT-1.1: Base BGP Session Parameters
- RT-1.2: BGP Policy & Route Installation
- RT-1.3: BGP Route Propagation
- RT-1.4: BGP Graceful Restart
- RT-1.5: BGP Prefix Limit
- RT-1.7: Local BGP Test
- RT-1.10: BGP Keepalive and HoldTimer Configuration Test
- RT-1.11: BGP remove private AS
- RT-1.12: BGP always compare MED
- RT-1.14: BGP Long-Lived Graceful Restart
- RT-1.19: BGP 2-Byte and 4-Byte ASN support
- RT-1.21: BGP TCP MSS and PMTUD
- RT-1.23: BGP AFI SAFI OC DEFAULTS
- RT-1.24: BGP 2-Byte and 4-Byte ASN support with policy
- RT-1.25: Management network-instance default static route
- RT-1.26: Basic static route support
- RT-1.27: Static route to BGP redistribution
- RT-1.28: BGP to IS-IS redistribution
- RT-1.29: BGP chained import/export policy attachment
- RT-1.30: BGP nested import/export policy attachment
- RT-1.32: BGP policy actions - MED, LocPref, prepend, flow-control
- RT-1.33: BGP Policy with prefix-set matching
- RT-1.34: BGP route-distance configuration
- RT-1.51: BGP multipath ECMP
- RT-1.52: BGP multipath UCMP support with Link Bandwidth Community
- RT-1.53: prefix-list test
- RT-1.54: BGP Override AS-path split-horizon
- RT-1.55: BGP session mode (active/passive)
- RT-2.1: Base IS-IS Process and Adjacencies
- RT-2.2: IS-IS LSP Updates
- RT-2.6: IS-IS Hello-Padding enabled at interface level
- RT-2.7: IS-IS Passive is enabled at interface level
- RT-2.8: IS-IS metric style wide not enabled
- RT-2.9: IS-IS metric style wide enabled
- RT-2.10: IS-IS change LSP lifetime
- RT-2.11: IS-IS Passive is enabled at the area level
- RT-2.12: Static route to IS-IS redistribution
- RT-2.13: Weighted-ECMP for IS-IS
- RT-2.14: IS-IS Drain Test
- RT-2.15: IS-IS Graceful Restart Helper
- RT-3.1: Policy based VRF selection
- RT-3.2: Multiple <Protocol, DSCP> Rules for VRF Selection
- RT-4.10: AFTs Route Summary
- RT-4.11: AFTs Route Summary
- RT-5.1: Singleton Interface
- RT-5.2: Aggregate Interfaces
- RT-5.3: Aggregate Balancing
- RT-5.4: Aggregate Forwarding Viable
- RT-5.5: Interface hold-time
- RT-5.6: Interface Loopback mode
- RT-5.7: Aggregate Not Viable All
- RT-5.8: IPv6 Link Local
- RT-5.9: Disable IPv6 ND Router Arvetisment
- RT-5.10: IPv6 Link Local generated by SLAAC
- RT-6.1: Core LLDP TLV Population
- RT-7.1: BGP default policies
- RT-7.2: BGP Policy Community Set
- RT-7.3: BGP Policy AS Path Set
- RT-7.4: BGP Policy AS Path Set and Community Set
- RT-7.5: BGP Policy - Match and Set Link Bandwidth Community
- RT-7.8: BGP Policy Match Standard Community and Add Community Import/Export Policy
- RT-7.11: BGP Policy - Import/Export Policy Action Using Multiple Criteria
- RT-14.2: GRIBI Route Test
- SEC-3.1: Authentication
- SFLOW-1: sFlow Configuration and Sampling
- System-1: System testing
- TE-1.1: Static ARP
- TE-1.2: My Station MAC
- TE-2.1: gRIBI IPv4 Entry
- TE-2.2: gRIBI IPv4 Entry With Aggregate Ports
- TE-3.1: Base Hierarchical Route Installation
- TE-3.2: Traffic Balancing According to Weights
- TE-3.3: Hierarchical weight resolution
- TE-3.5: Ordering: ACK Received
- TE-3.6: ACK in the Presence of Other Routes
- TE-3.7: Base Hierarchical NHG Update
- TE-3.31: Hierarchical weight resolution with PBF
- TE-4.1: Base Leader Election
- TE-4.2: Persistence Mode
- TE-5.1: gRIBI Get RPC
- TE-6.1: Route Removal via Flush
- TE-6.2: Route Removal In Non Default VRF
- TE-8.1: DUT Daemon Failure
- TE-8.2: Supervisor Failure
- TE-9.2: MPLS based forwarding Static LSP
- TE-9.3: FIB FAILURE DUE TO HARDWARE RESOURCE EXHAUST
- TE-9: gRIBI MPLS Compliance
- TE-10: gRIBI MPLS Forwarding
- TE-11.1: Backup NHG: Single NH
- TE-11.2: Backup NHG: Multiple NH
- TE-11.3: Backup NHG: Actions
- TE-11.21: Backup NHG: Multiple NH with PBF
- TE-11.31: Backup NHG: Actions with PBF
- TE-13.1: gRIBI route ADD during Failover
- TE-13.2: gRIBI route DELETE during Failover
- TE-14.1: gRIBI Scaling
- TE-14.2: encap and decap scale
- TE-15.1: gRIBI Compliance
- TE-16.1: basic encapsulation tests
- TE-16.2: encapsulation FRR scenarios
- TE-16.3: encapsulation FRR scenarios
- TE-17.1: VRF selection policy driven TE
- TR-6.1: Remote Syslog feature config
- TRANSCEIVER-1: Telemetry: 400ZR Chromatic Dispersion(CD) telemetry values streaming
- TRANSCEIVER-3: Telemetry: 400ZR Optics firmware version streaming
- TRANSCEIVER-4: Telemetry: 400ZR RX input and TX output power telemetry values streaming.
- TRANSCEIVER-5: Configuration: 400ZR channel frequency, output TX launch power and operational mode setting.
- TRANSCEIVER-6: Telemetry: 400ZR Optics performance metrics (pm) streaming.
- TRANSCEIVER-7: Telemetry: 400ZR Optics inventory info streaming
- TRANSCEIVER-8: Telemetry: 400ZR Optics module temperature streaming.
- TRANSCEIVER-9: Telemetry: 400ZR TX laser bias current telemetry values streaming.
- TRANSCEIVER-10: Telemetry: 400ZR Optics FEC(Forward Error Correction) Uncorrectable Frames Streaming.
- TRANSCEIVER-11: Telemetry: 400ZR Optics logical channels provisioning and related telemetry.
- TRANSCEIVER-12: Telemetry: 400ZR Transceiver Supply Voltage streaming.
- TRANSCEIVER-13: Configuration: 400ZR Transceiver Low Power Mode Setting.
- TUN-1.4: Interface based IPv6 GRE Encapsulation
- TUN-1.9: GRE inner packet DSCP
- Test Plans