SYNOPSIS
    px2_configure.pl COMMAND [ARGUMENTS]

DESCRIPTION
    PX2 deployment and configuration utility.

COMMANDS
    configure LIST IPS
        Configure some or all devices (network settings, unit name and SNMP
        settings).

        The behavior of this command is different depending on whether
        concrete IP addresses or the 'all' keyword is specified:

        * If IP addresses are specified the program will contact each
          device, read its serial number and search for a matching entry in
          the device list. It will then change the device's network settings
          to the values from the device list. The initial IP addresses do
          not have to match the values from the device list, they might as
          well be dynamically assigned by a DHCP server.

        * If the 'all' keyword is specified the IP addresses are taken from
          the device list. The devices' network settings are expected to be
          properly configured at this point, so the network configuration
          part will be skipped.

    verify LIST IPS
        Verify device settings and SNMP access.

    identify LIST IPS
        Identify some or all devices (show a distinctive string for two
        seconds in each unit's display).

    reboot LIST IPS
        Reboot some or all devices.

    fetch_fitness LIST OUTFILE IPS
        Fetch fitness data from some or all devices and write them to a file
        in CSV format.

    update LIST IMAGE IPS
        Device firmware update. The firmware image will be sequentially
        uploaded to each device, then all devices will be instructed to
        perform the firmware update in parallel.

    print_timezones IP
        Print list of supported timezones with its IDs.

    set_timezone LIST TZID IPS
        Set the timezone of all devices.

ARGUMENTS
    LIST
        Device list in CSV format.

    IPS Device IP addresses; use 'all' to run on all IPs in the CSV file.

    IP  Device IP address.

    OUTFILE
        Output file name.

    IMAGE
        Firmware image file.

    TZID
        Timezone ID as printed by the "print_timezones" command.

EXAMPLES
    px2_configure.pl configure devices.csv 192.168.2.3
        Connect to the device at 192.168.2.3, read its serial number and
        look it up in the device list file named devices.csv. Configure the
        device's network, PDU name and SNMP settings.

    px2_configure.pl verify devices.csv all
        Verify the network settings, PDU name and SNMP access for all
        devices in the list file.

    px2_configure.pl update devices.csv pdu-px2-020106-26030.bin all
        Update all devices to firmware version 2.1.6.

DEVICE LIST FORMAT
    The device list file contains a list of PX2 devices in CSV format. It
    could e.g. be exported from an inventory spreadsheet. Each device line
    contains five or six fields, seperated by commas:

    1. Unit Serial Number
    2. PDU Name
    3. IP Address
    4. Gateway IP Address
    5. Netmask
    6. Optional comment; the line is ignored if "ignore" is included here

    Lines with less than five fields are silently ignored. Likewise, lines
    that do not contain a valid serial number (i.e. a string starting with
    'P') are disregarded.

REQUIREMENTS
    The following Perl modules are required to run this script:

    * Raritan PX2 RPC bindings (distributed along with this script)

    * libwww-perl <http://search.cpan.org/dist/libwww-perl/>

    * LWP::Protocol::https <http://search.cpan.org/dist/LWP-Protocol-https/>

    * JSON <http://search.cpan.org/dist/JSON/>

    * JSON-RPC-Common <http://search.cpan.org/dist/JSON-RPC-Common/>

    * perl-Error <http://search.cpan.org/dist/Error/>

    * Test-Simple <http://search.cpan.org/dist/Test-Simple/>

    Additionally, the verify command uses the *snmpget* utility to verify
    SNMP access.