Sync docs

docgen/device_page_notes.js

@@ -4,6 +4,36 @@ const notes = [
         note: `
 ### Pairing
 Press and hold the button on the device until the blue light starts blinking, release it and and the device will automatically join.
+`,
+    },
+    {
+        model: ['AV2010/29A'],
+        deviceTypeSpecificConfiguration: true,
+        note: `
+### Controlling
+Trigger the siren sound and lights, duration can be indicated in seconds. The strobe parameter must always be false
+\`\`\`json
+topic: 'zigbee2mqtt/friendly name/set'
+payload: '{"warning": {"duration": 3, "strobe": false}}'
+\`\`\`
+
+5 short beeps. If the alarm is on, it stops:
+\`\`\`json
+topic: 'zigbee2mqtt/friendly name/set'
+payload: '{"warning": {"level": "medium"}}'
+\`\`\`
+5 long beeps. If the alarm is on, it stops:
+\`\`\`json
+topic: 'zigbee2mqtt/friendly name/set'
+payload:
+'{"warning": {"level": "high"}}'
+\`\`\`
+
+1 short beeps. If the alarm is on, it stops:
+\`\`\`json
+topic: 'zigbee2mqtt/friendly name/set'
+payload: '{"warning": {"level": "very_high"}}'
+\`\`\`
 `,
     },
     {
@@ -18,6 +48,65 @@ The \`triple\`, \`quadruple\`, \`hold\` and \`release\` is not supported by all
         note: `
 ### Firmware
 This is a Texas Instruments CC1352P-2, CC2652RB or CC2652R flashed with the following firmware: https://github.com/Koenkk/Z-Stack-firmware/tree/master/router/Z-Stack_3.x.0/bin
+`,
+    },
+    {
+        model: ['L122FF63H11A5.0W', 'L122CB63H11A9.0W', 'L122AA63H11A6.5W', 'C422AC14D41H140.0W', 'C422AC11D41H140.0W'],
+        note: `
+### Pairing
+Factory reset the light.
+After resetting the light it will automatically connect.
+
+The light should be turned off for at least 10 seconds. After that, the on- and off-phases should last around 2 to 5 seconds.
+Start with light on, then off, and then 3 “on’s”, wait in the 3rd ON state.
+`,
+    },
+    {
+        model: ['F122SB62H22A4.5W'],
+        note: `
+### Pairing
+Factory reset the light bulb.
+After resetting the bulb will automatically connect.
+
+The bulb should be turned off for at least 10 seconds. After that, the on- and off-phases should last around 2 to 5 seconds.
+Start with bulb on, then off, and then 3 “on’s”, wait in the 3rd ON state.
+`,
+    },
+    {
+        model: ['RL460WHZHA69'],
+        note: `
+### Pairing
+The bulb automatically pairs after coming out of the box.
+
+To factory reset the bulb; turn on and off the power 6 times within a few seconds. After resetting the bulb will automatically connect.
+`,
+    },
+    {
+        model: ['TI0001-switch', 'TI0001-switch-2gang', 'TI0001-socket', 'TI0001-dimmer'],
+        note: `
+After pairing device will be shown as "TI0001" device. Need to manually trigger a re-configure of the device either using web-frontend
+of Zigbee2MQTT or using [MQTT message](../information/mqtt_topics_and_message_structure.html#zigbee2mqttbridgerequestdeviceconfigure) right after pairing.
+In case of problems it's recommended to remove device and than retry pairing and re-configuring device.
+
+### Important
+These devices can only be used on channel 26.
+These devices are locked to the manufacturer's network key (ext_pan_id).
+Your configuration file [data/configuration.yaml](../information/configuration) must contain the following:
+
+\`\`\`yaml
+advanced:
+  ext_pan_id: [33,117,141,25,0,75,18,0]
+  channel: 26
+\`\`\`
+
+Therefore these devices may not co-existence with other Zigbee devices.
+Maybe, you need to add a dedicated coordinator and create a new network for Livolo.
+If you decided to create a new network, you should specify another 'pan_id'.
+
+\`\`\`yaml
+advanced:
+  pan_id: 6756
+\`\`\`
 `,
     },
     {
@@ -1163,6 +1252,13 @@ The E1745 can be bound to groups using [binding](../information/binding).
 ## Detection cooldown (E1745 version)
 This device will pause detection of presence for approximately 1 min 37 sec after detection. In other words; with continuous detection, every 1:37 a new publish (occupancy: true) will be done.
 Cooldown of detection is 3 min. In other words; 3 min after last published detection (and trigger no longer present) occupancy will be published as false.
+
+The cooldown detection timeout can be overriden by using the following device config option:
+* \`occupancy_timeout\`: Timeout (in seconds) after which the \`occupancy: false\` message is sent.
+
+Please note that setting \`occupancy_timeout\` lower than the device re-trigger time (around 1m30s) means \`occupancy: true\` will only be sent again when motion is detected after the re-trigger time.
+This allows an external automation system to observe the detection cycles (detection -> idle -> detection -> idle) and implement more complex automation flows.
+For simple automations, setting \`occupancy_timeout\` greater than the re-trigger time is probably desired.
 `,
     },
     {

docs/devices/014G2461.md

@@ -12,7 +12,7 @@ description: "Integrate your Danfoss 014G2461 via Zigbee2MQTT with whatever smar
 | Model | 014G2461  |
 | Vendor  | Danfoss  |
 | Description | Ally thermostat |
-| Exposes | battery, lock (state), climate (occupied_heating_setpoint, local_temperature, pi_heating_demand), linkquality |
+| Exposes | battery, lock (state), mounted_mode, heat_required, window_open_internal, setpoint_change_source, climate (occupied_heating_setpoint, local_temperature, pi_heating_demand), linkquality |
 | Picture | ![Danfoss 014G2461](../images/devices/014G2461.jpg) |
 
 ## Notes
@@ -52,6 +52,30 @@ The current state of this lock is in the published state under the `keypad_locko
 To control this lock publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"keypad_lockout": "1"}` or `{"keypad_lockout": "0"}`.
 To read the current state of this lock publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"keypad_lockout": ""}`.
 
+### Mounted_mode (binary)
+Mode in which the unit is mounted. This is set to `false` for normal mounting or `true` for vertical mounting.
+Value can be found in the published state on the `mounted_mode` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+If value equals `true` mounted_mode is ON, if `false` OFF.
+
+### Heat_required (binary)
+Wether or not the unit needs warm water.
+Value can be found in the published state on the `heat_required` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+If value equals `true` heat_required is ON, if `false` OFF.
+
+### Window_open_internal (binary)
+Most likely related to the option to set Window Detection mode.
+Value can be found in the published state on the `window_open_internal` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+If value equals `1` window_open_internal is ON, if `0` OFF.
+
+### Setpoint_change_source (binary)
+Values observed are `0` (set locally) or `2` (set via Zigbee).
+Value can be found in the published state on the `setpoint_change_source` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+If value equals `0` setpoint_change_source is ON, if `1` OFF.
+
 ### Climate 
 This climate device supports the following features: `occupied_heating_setpoint`, `local_temperature`, `pi_heating_demand`.
 - `occupied_heating_setpoint`: Temperature setpoint. To control publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"occupied_heating_setpoint": VALUE}` where `VALUE` is the °C between `6` and `28`. To read send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"occupied_heating_setpoint": ""}`.
@@ -75,8 +99,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 lock:
@@ -89,6 +113,38 @@ lock:
     payload_unlock: "0"
     command_topic_postfix: "keypad_lockout"
 
+binary_sensor:
+  - platform: "mqtt"
+    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
+    availability_topic: "zigbee2mqtt/bridge/state"
+    value_template: "{{ value_json.mounted_mode }}"
+    payload_on: true
+    payload_off: false
+
+binary_sensor:
+  - platform: "mqtt"
+    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
+    availability_topic: "zigbee2mqtt/bridge/state"
+    value_template: "{{ value_json.heat_required }}"
+    payload_on: true
+    payload_off: false
+
+binary_sensor:
+  - platform: "mqtt"
+    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
+    availability_topic: "zigbee2mqtt/bridge/state"
+    value_template: "{{ value_json.window_open_internal }}"
+    payload_on: 1
+    payload_off: 0
+
+binary_sensor:
+  - platform: "mqtt"
+    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
+    availability_topic: "zigbee2mqtt/bridge/state"
+    value_template: "{{ value_json.setpoint_change_source }}"
+    payload_on: 0
+    payload_off: 1
+
 climate:
   - platform: "mqtt"
     availability_topic: "zigbee2mqtt/bridge/state"
@@ -106,8 +162,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 
 sensor:

docs/devices/046677476816.md

@@ -158,8 +158,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 
 sensor:

docs/devices/046677551780.md

@@ -158,8 +158,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 
 sensor:

docs/devices/046677552343.md

@@ -86,8 +86,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 
 sensor:

docs/devices/064873.md

@@ -53,8 +53,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 sensor:
@@ -68,8 +68,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/064888.md

@@ -54,8 +54,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/067646.md

@@ -53,8 +53,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 sensor:
@@ -68,8 +68,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/067694.md

@@ -56,8 +56,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 sensor:
@@ -71,8 +71,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/067771.md

@@ -158,8 +158,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/067773.md

@@ -80,8 +80,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 sensor:
@@ -95,8 +95,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}

docs/devices/067774.md

@@ -74,8 +74,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "%"
     value_template: "{{ value_json.battery }}"
+    unit_of_measurement: "%"
     device_class: "battery"
 
 sensor:
@@ -89,8 +89,8 @@ sensor:
   - platform: "mqtt"
     state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
     availability_topic: "zigbee2mqtt/bridge/state"
-    unit_of_measurement: "lqi"
     value_template: "{{ value_json.linkquality }}"
+    unit_of_measurement: "lqi"
     icon: "mdi:signal"
 ```
 {% endraw %}